You use OSPF as your network routing protocol. You use the command show ip route and you see several routes described as O,O IA,O E1,and O E2. What routes are in your area?()A、O IAB、O E1C、O E2D、O

You use OSPF as your network routing protocol. You use the command show ip route and you see several routes described as O,O IA,O E1,and O E2. What routes are in your area?()

  • A、O IA
  • B、O E1
  • C、O E2
  • D、O

相关考题:

Which three route filtering statements are true?() A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface

You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?()A. OSPF authentication errors between some of the routersB. Two routers have the same OSPF router IDC. Issues with mistuned OSPF timersD. OSPF LSA pacing issues between some of the routersE. OSPF neighbor adjacency problems between some of the routers

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?()A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

Which IOS command would you use to find out which networks are routed by a particular OSPF process() A.show ip ospfB.show ip routeC.show ip protocolsD.show ip ospf databaseE.None of the other alternatives apply

Which command should you use to verify what networks are being routed by a given OSPF process() A.show ip ospfB.show ip routeC.show ip protocolD.show ip ospfdatabaseE.None of the other alternatives apply

Your MPLS implementation is currently using internal backdoor links. What can you do to minimize the impact of having these links?() A. use BGP as the CE-PE routing protocolB. use OSPF as the CE-PE routing protocolC. use EIGRP as the CE-PE routing protocolD. use the SP to redistribute routes as external routes for OSPF and EIGRPE. use route redistribution at each location to ensure external routes are imported into the IGP

A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network()。A、The router will use the static route.B、The router will use the OSPF route.C、The router will use the EIGRP route.D、The router will load balance and use all three routes.

You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?()A、OSPF authentication errors between some of the routersB、Two routers have the same OSPF router IDC、Issues with mistuned OSPF timersD、OSPF LSA pacing issues between some of the routersE、OSPF neighbor adjacency problems between some of the routers

Which two items should you know when configuring OSPF to dynamically learn routes? ()(Choose two.)A、OSPF area IDB、OSPF neighbor addressC、OSPF loopback addressD、OSPF authentication type

A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?()A、The router will use the static route.B、The router will use the OSPF route.C、The route will use the EIGRP route.D、The router will load balance and use all three routes.

Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? ()A、 Never use passive interfaces.B、 Use NSSA areas from the core down.C、 Use totally stub areas to stop type 3 LSAs.D、 Use the lowest Ethernet interface IP address as the router ID.E、 Tune OSPF timers to enable OSPF to achieve quicker convergence

Which command should you use to verify what networks are being routed by a given OSPFprocess?()A、show ip ospfB、show ip routeC、show ip protocolD、show ip ospf databaseE、None of the other alternatives apply

Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? ()A、Never use passive interfaces.B、Use NSSA areas from the core down.C、Use totally stub areas to stop type 3 LSAs.D、Use the lowest Ethernet interface IP address as the router ID.E、Tune OSPF timers to enable OSPF to achieve quicker convergence.

when you use LSA type 4 in OSPF environment?

Your MPLS implementation is currently using internal backdoor links. What can you do to minimize the impact of having these links?()A、 use BGP as the CE-PE routing protocolB、 use OSPF as the CE-PE routing protocolC、 use EIGRP as the CE-PE routing protocolD、 use the SP to redistribute routes as external routes for OSPF and EIGRPE、 use route redistribution at each location to ensure external routes are imported into the IGP

Which three route filtering statements are true?()A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface

Which IOS command would you use to find out which networks are routed by a particular OSPF process()A、show ip ospfB、show ip routeC、show ip protocolsD、show ip ospf databaseE、None of the other alternatives apply

Which mechanism can you use to achieve sub-second failover for link failure detection when a switched Ethernet media is used and loss of signal is not supported by the link provider?()A、OSPF standard hellosB、Cisco Discovery Protocol link detectionC、Bidirectional Forwarding DetectionD、Fast Link PulseE、autonegotiation

问答题when you use LSA type 4 in OSPF environment?

单选题You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?()AOSPF authentication errors between some of the routersBTwo routers have the same OSPF router IDCIssues with mistuned OSPF timersDOSPF LSA pacing issues between some of the routersEOSPF neighbor adjacency problems between some of the routers

多选题You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriate ARB. Which two commands should you use from the [edit] hierarchy level within the JUNOS software configuration mode?()Aset protocols ospf area-range network/mask-lengthBset protocols ospf area area-id nssa area-range network/mask-lengthCset protocols ospf area area-id area-range network/mask-length restrictDset protocols ospf area area-id nssa area-range network/mask-length restrict

多选题Which two commands would you use to view OSPF routes?()Ashow ip route ospfBshow ospf routesCshow route protocol ospfDshow route

单选题A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?()AThe router will use the static route.BThe router will use the OSPF route.CThe route will use the EIGRP route.DThe router will load balance and use all three routes.

单选题You use OSPF as your network routing protocol. You use the command show ip route and you see several routes described as O, O IA, O E1, and O E2. What routes are in your area? ()A O IAB O E1C O E2D O

单选题Which IOS command would you use to find out which networks are routed by a particular OSPFprocess?()Ashow ospfBshow ip routeCshow ip protocolsDshow ip ospf databaseENone of the other alternatives apply

多选题You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriateABR. Which two commands should you use from the [edit] hierarchy level within JUNOS configuration mode?()Aset protocols ospf area-range network/mask-lengthBset protocols ospf area area-id nssa area-range network/mask-lengthCset protocols ospf area area-id area-range network/mask-length restrictDset protocols ospf area area-id nssa area-range network/mask-length restrict

单选题Which IOS command would you use to find out which networks are routed by a particular OSPF process()Ashow ip ospfBshow ip routeCshow ip protocolsDshow ip ospf databaseENone of the other alternatives apply