R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands.Which of the following is true in this case?（）A. The show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.B. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.C. The show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.D. T he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.E. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands.Which of the following is true in this case?（）
A. The show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.
B. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.
C. The show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.
D. T he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.
E. The show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
相关考题：
若有以下程序段: int r=8; print("%d\n",r1): 输出结果是( )。 A.16B.8S 若有以下程序段： int r=8； print("％d\n"，r1)： 输出结果是（ ）。A.16B.8C.4D.2
Router R1 has eBGP connections to I1 and I 2, routers at the same ISP. The company that owns R1 can use public address range 130.1.16.0/20. The following output lists all the IP routes in R1‘s routing table within this rangE. Which of the following answers would cause R1 to advertise the 130.1.1 6.0/20 prefix to its eBGP peers?（）R1 show ip route 130.1.16.0 255.255.240.0 longer - prefixes! lines omitteD...O 130.1.16.0/24 [110/3] via 10.5.1.1, 00:14:36, FastE thernet0/1O 130.1.17.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1O 130.1.18.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1A. Configure R1 with the network 130.1.16.0 mask 255.255.240.0 command.B. Configure R1 with the network 130.1.16 .0 mask 255.255.240.0 summaryonly command.C. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed.D. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed, and create a BGP summary for 130.1.16.0/20.
Which BGP option i s required when load sharing over multiple equal － bandwidth parallel links from a single CE router to a single ISP router over eBGP?() A. eBGP MultipathB. eBGP MultihopC. BGP SynchronizationD. Public AS numbers
Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? () A. Router R2 will be preferred because it has the higher neighbor IP address.B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.C. Router R1 will be preferred because it has a lower local preference.D. Router R2 will be preferred because it has a higher local preference.E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.F. Router R1 will be preferred because it has the lower neighbor IP address.
Examine the above configuration. What does the route map named test accomplish?() A. permits only the 10.0.0.0/8 prefix to be advertised to the 10.1.1.1 neighborB. marks all prefixes received fro m the 10.1.1.1 neighbor with a MED of 200C. marks the 10.0.0.0/8 prefix advertised to the 10.1.1.1 neighbor with a MED of 200D. permits only the 10.0.0.0/8 prefix to be received from the 10.1.1.1 neighborE. marks all prefixes advertised to the 10.1.1 .1 neighbor with a MED of 200F. marks the 10.0.0.0/8 prefix received from the 10.1.1.1 neighbor with a MED of 200
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）A. debug eigrp packetB. show key chainC. show ip eigrp neighbor failureD. show clock
Which of these best identifies the types of prefixes a router running BGP will advertise to an EBGP peer？ （）A、 prefixes received from any other BGP peer and prefixes locally originated via networkstatements or redistributed to BGPB、 all prefixes in its IP routing tableC、 only prefixes received from EBGP peers and prefixes locally originated via network statements or redistributedD、 only prefixes received from EBGP peers and prefixes received from route reflectorsE、 all prefixes in its routing table except the prefixes received from other EBGP peersF、 all prefixes in its routing table except the prefixes received from other IBGP peers
Which BGP option i s required when load sharing over multiple equal - bandwidth parallel links from a single CE router to a single ISP router over eBGP?（）A、eBGP MultipathB、eBGP MultihopC、BGP SynchronizationD、Public AS numbers
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is not configured as a route reflector？（）A、prefixes received from any other BGP peer and prefixes locally originated via networkstatements or redistributedB、all prefixes in its routing tableC、prefixes received from EBGP peers and prefixes locally originated via network statements or redistributedD、prefixes received from EBGP peers and prefixes received from route reflectorsE、prefixes received from other IBGP peers， prefixes received from EBGP peers，and prefixes redistributed to BGPF、prefixes received from other IBGP peers and prefixes received from route reflectors
Which of these best identifies the types of prefixes a router running BGP will advertise to an EBGP peer？（）A、prefixes received from any other BGP peer and prefixes locally originated via network statements or redistributed to BGPB、all prefixes in its IP routing tableC、only prefixes received from EBGP peers and prefixes locally originated via network statements or redistributedD、only prefixes received from EBGP peers and prefixes received from route reflectorsE、all prefixes in its routing table except the prefixes received from other EBGP peersF、all prefixes in its routing table except the prefixes received from other IBGP peers
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails. Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）A、debug eigrp packetB、show key chainC、show ip eigrp neighbor failureD、show clock
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands. Which of the following is true in this case?（）A、The show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.B、The show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.C、The show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.D、T he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.E、The show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
多选题Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（） interface f0/0 ipv6 address 2345:0:0:8::1/64A2345:0:0:8::1B2345:0:0:8:0:FF:FE11:1111CFE80::8:0:FF:FE11:1111DFE80:0:0:8::1
单选题Which of these best identifies the types of prefixes a router running BGP will advertise to an EBGP peer？（）Aprefixes received from any other BGP peer and prefixes locally originated via network statements or redistributed to BGPBall prefixes in its IP routing tableConly prefixes received from EBGP peers and prefixes locally originated via network statements or redistributedDonly prefixes received from EBGP peers and prefixes received from route reflectorsEall prefixes in its routing table except the prefixes received from other EBGP peersFall prefixes in its routing table except the prefixes received from other IBGP peers
单选题Router R1 has eBGP connections to I1 and I 2, routers at the same ISP. The company that owns R1 can use public address range 130.1.16.0/20. The following output lists all the IP routes in R1's routing table within this rangE. Which of the following answers would cause R1 to advertise the 130.1.1 6.0/20 prefix to its eBGP peers?（） R1# show ip route 130.1.16.0 255.255.240.0 longer - prefixes ! lines omitteD... O 130.1.16.0/24 [110/3] via 10.5.1.1, 00:14:36, FastE thernet0/1 O 130.1.17.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1 O 130.1.18.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1AConfigure R1 with the network 130.1.16.0 mask 255.255.240.0 command.BConfigure R1 with the network 130.1.16 .0 mask 255.255.240.0 summaryonly command.CRedistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed.DRedistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed, and create a BGP summary for 130.1.16.0/20.
单选题R1 is currently advertising prefixes 1.0.0.0/8, 2.0.0.0/8, and 3.0.0.0/8 over its eBGP connection to neighbor 2.2.2.2 (R2). An engineer configures a prefix list (fred) on R1 that permits only 2.0.0.0/8 and then enables the filter with the neighbor R2 prefix- list fred out command. Upon exiting configuration mode, the engineer uses some show commands on R1, but no other commands. Which of the following is true in this case?（）AThe show ip bgp neighbor 2 .2.2.2 received -routes command lists the three original prefixes.BThe show ip bgp neighbor 2.2.2.2 advertised - routes command lists the three original prefixes.CThe show ip bgp neighbor 2.2.2.2 routes command lists the three original prefixes.DT he show ip bgp neighbor 2.2.2.2 routes command lists only 2.0.0.0/8.EThe show ip bgp neighbor 2.2.2.2 advertised - routes command lists only 2.0.0.0/8.
单选题Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is not configured as a route reflector？（）Aprefixes received from any other BGP peer and prefixes locally originated via networkstatements or redistributedBall prefixes in its routing tableCprefixes received from EBGP peers and prefixes locally originated via network statements or redistributedDprefixes received from EBGP peers and prefixes received from route reflectorsEprefixes received from other IBGP peers， prefixes received from EBGP peers，and prefixes redistributed to BGPFprefixes received from other IBGP peers and prefixes received from route reflectors
单选题Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is not configured as a route reflector？ （）A prefixes received from any other BGP peer and prefixes locally originated via network statements or redistributedB all prefixes in its routing tableC prefixes received from EBGP peers and prefixes locally originated via network statements or redistributedD prefixes received from EBGP peers and prefixes received from route reflectorsE prefixes received from other IBGP peers， prefixes received from EBGP peers， and prefixes redistributed to BGPF prefixes received from other IBGP peers and prefixes received from route reflectors
单选题Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）AR1 has been configured with an ip default- network 2.0.0.0 command.BR1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.CR1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.DAnother router has been configured with an ip default - network 2.0.0.0 command.EAnother router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.