单选题OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）AOnly the router A loopback interface is parti cipating in the OSPF routing processBNone of the router A interfaces are participating in the OSPF routing processCRouter A is using the loopback interface IP address as its OSPF router IDDRouter A does not have any reachable OSPF neighbors
单选题
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）
A
Only the router A loopback interface is parti cipating in the OSPF routing process
B
None of the router A interfaces are participating in the OSPF routing process
C
Router A is using the loopback interface IP address as its OSPF router ID
D
Router A does not have any reachable OSPF neighbors
参考解析
解析：
暂无解析
相关考题：
You execute the following PL／SQL:Which two statements are true?() A. Fine-Grained Auditing (FGA) is enabled for the PRICE column in the PRODUCTS table for SELECT statements only when a row with PRICE 10000 is accessed.B. FGA is enabled for the PRODUCTS.PRICE column and an audit record is written whenever a row with PRICE 10000 is accessed.C. FGA is enabled for all DML operations by JIM on the PRODUCTS.PRICE column.D. FGA is enabled for the PRICE column of the PRODUCTS table and the SQL statements is captured in the FGA audit trial.
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E. None of the other answers is correct.
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterAping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.What can you conclude about router A?（）A. Only the router A loopback interface is parti cipating in the OSPF routing processB. None of the router A interfaces are participating in the OSPF routing processC. Router A is using the loopback interface IP address as its OSPF router IDD. Router A does not have any reachable OSPF neighbors
You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes.Which two things should you verify to troubleshoot this problem?（）A. The border router is using a proper seed metric for OSPFB. The border ro uter is using a proper seed metric for EIGRPC. The administrative distance is set for OSPF and EIGRPD. The missing EIGRP routes are present in the routing table of the border routerE. The subnet keyword on the border router in the redistribute EIG RP command
You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes.What should you verify to troubleshoot this problem?（）A. The border router is using a proper seed metric for OSPFB. The border router is using a proper seed metric for EIGRPC. The administrative distance is set for OSPF and EIGRPD. The missing OSPF routes are present in the routing table of the border routerE. The subnet keyword on the border router in the redistribute OSPF command
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）A. OSPF authentication errors between some of the routersB. Two routers have the same OSPF router IDC. Issues with mistuned OSPF timersD. OSPF LSA pacing issues between some of the routersE. OSPF neighbor adjacency problems between some of the routers
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
You are troubleshooting a WAN connection for TestKing, and on the router you execute the, debug ppp authentication command, and view the following output:What kind of handshake was used for the PPP authentication?（）A. one-wayB. two-wayC. three-wayD. No handshakes required during authenticationE. None of the above
You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way:Router(config) router ospf 99Router(config-if) network 10.0.0.0 255.0.0.0 area 0Based on this information, what is the most likely problem?（）A. The process id is configured improperly.B. The OSPF area is configured improperly.C. The network wildcard mask is configured improperly.D. The network number is configured improperly.E. The AS is configured improperly.F. The network subnet mask is configured improperly.G. All of the above are likely problems.
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:TK1(config) router ospf 1TK1(config-router) network 10.10.10.0 255.255.255.0 area 0After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A. The AS is not correctly configuredB. The network subnet mask is incorrectly configuredC. The network wildcard mask is configured incorrectlyD. The network number is not correctly configuredE. The process id is configured incorrectlyF. None of the above
Which of the following OSPF commands, when used together, will put the network 192.168.10.0／24 into OSPF area 0?() A. Router(config-router)# network 192.168.10.0 0.0.0.255 0B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D. Router(config)# router ospf 0E. Router(config)# router ospf 1
Which of the following describe the process identifier that is used to run OSPF on a router?() A. It is locally significant.B. It is globally significant.C. It is needed to identify a unique instance of an OSPF database.D. It is an optional parameter required only if multiple OSPF processes are running on the router.E. All routers in the same OSPF area must have the same process ID if they are to exchange routing information.
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A、The AS is not correctly configuredB、The network subnet mask is incorrectly configuredC、The network wildcard mask is configured incorrectlyD、The network number is not correctly configuredE、The process id is configured incorrectlyF、None of the above
Which of the following data structures exist on a router for the OSPF routing protocol？（）A、OSPF topology tableB、OSPF interface tableC、OSPF routing information baseD、OSPF link-state databaseE、OSPF adjacency tableF、OSPF neighbor table
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?（）A、OSPF authentication errors between some of the routersB、Two routers have the same OSPF router IDC、Issues with mistuned OSPF timersD、OSPF LSA pacing issues between some of the routersE、OSPF neighbor adjacency problems between some of the routers
You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes. What should you verify to troubleshoot this problem?（）A、The border router is using a proper seed metric for OSPFB、The border router is using a proper seed metric for EIGRPC、The administrative distance is set for OSPF and EIGRPD、The missing OSPF routes are present in the routing table of the border routerE、The subnet keyword on the border router in the redistribute OSPF command
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）A、Router(config-router)# network 192.168.10.0 0.0.0.255 0B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D、Router(config)# router ospf 0E、Router(config)# router ospf 1
Which two of the following actions must an OSPF NSF-capable router execute after a supervisor engine switchover?（） (Choose two.)A、Re-learn the available OSPF neighbors with neighbor relationship restartB、Send the graceful restart messageC、Re-acquire the link state database content for the networkD、Re-learn the available OSPF neighbors without neighbor relationship restart
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）A、Only the router A loopback interface is parti cipating in the OSPF routing processB、None of the router A interfaces are participating in the OSPF routing processC、Router A is using the loopback interface IP address as its OSPF router IDD、Router A does not have any reachable OSPF neighbors
You issued the following statement： SQLALTER DATABASE ENABLE RESUMABLE TIMEOUT n； What will be the result of issuing the above statement？（）A、The command will not execute successfully because TIMEOUT is an invalid clause with the ALTER DATABASE ENABLE RESUMABLE command.B、 The command will not execute successfully because resumable space allocation is enabled at the session level.C、 The command will execute successfully and resumable space will be allocated at the session level.D、 The command will execute successfully and resumable space will be allocated at the instance level.
多选题Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）ARouter(config-router)# network 192.168.10.0 0.0.0.255 0BRouter(config-router)# network 192.168.10.0 0.0.0.255 area 0CRouter(config-router)# network 192.168.10.0 255.255.255.0 area 0DRouter(config)# router ospf 0ERouter(config)# router ospf 1
单选题You issued the following statement： SQLALTER DATABASE ENABLE RESUMABLE TIMEOUT n； What will be the result of issuing the above statement？（）AThe command will not execute successfully because TIMEOUT is an invalid clause with the ALTER DATABASE ENABLE RESUMABLE command.B The command will not execute successfully because resumable space allocation is enabled at the session level.C The command will execute successfully and resumable space will be allocated at the session level.D The command will execute successfully and resumable space will be allocated at the instance level.
单选题You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes. What should you verify to troubleshoot this problem?（）AThe border router is using a proper seed metric for OSPFBThe border router is using a proper seed metric for EIGRPCThe administrative distance is set for OSPF and EIGRPDThe missing OSPF routes are present in the routing table of the border routerEThe subnet keyword on the border router in the redistribute OSPF command
单选题You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way: Router(config)# router ospf 99 Router(config-if)# network 10.0.0.0 255.0.0.0 area 0 Based on this information, what is the most likely problem?（）AThe process id is configured improperly.BThe OSPF area is configured improperly.CThe network wildcard mask is configured improperly.DThe network number is configured improperly.EThe AS is configured improperly.FThe network subnet mask is configured improperly.GAll of the above are likely problems.
单选题A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）AThe AS is not correctly configuredBThe network subnet mask is incorrectly configuredCThe network wildcard mask is configured incorrectlyDThe network number is not correctly configuredEThe process id is configured incorrectlyFNone of the above