OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）A、Only the router A loopback interface is parti cipating in the OSPF routing processB、None of the router A interfaces are participating in the OSPF routing processC、Router A is using the loopback interface IP address as its OSPF router IDD、Router A does not have any reachable OSPF neighbors
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）
- A、Only the router A loopback interface is parti cipating in the OSPF routing process
- B、None of the router A interfaces are participating in the OSPF routing process
- C、Router A is using the loopback interface IP address as its OSPF router ID
- D、Router A does not have any reachable OSPF neighbors
相关考题：
Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?() A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18A. This router has set the Weight of this route to 10.B. This router‘s BGP table lists this route as an iBGP route.C. This router‘s MED has been set to 10.D. This router‘s BGP table lists an AS_Path length of 10 for this route.
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（）External data:Originating router is 10.1.1.1AS number of route is 1External protocol is OSPF, external metric is 64Administrator tag is 0 (0x00000000)A. R1 is the router that redistributed the routeB. R1‘s metric to reach subnet 10.2.2.0/24 is 64C. The route was redistributed on a router that has a router ospf 1 command configuredD. R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
Which of the following answers can be verified as true based on the following command output from Router R1?（）R1show ip ospf virtual - linksVirtual Link OSPF_VL0 to router 4.4.4.4 is upRun as demand circuitDoNotAge LSA alloweD.Transit area 1, via interface FastEthernet0/1, Cost of using 3A. R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.B. The ping 4.4.4.4 command on R1 must currently be successful.C. R1‘s Fa0/0 OSPF cost is 3.D. 4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
The following output exists on Router R1, a router internal to area 1. What can you d etermine as true from the output of the show ip ospf database summary command?() A. The LSA was created by an ABR due to an area range command.B. The LSA was created by an ASBR due to a summary - address command.C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.D. None of the other answers is correct.
The following output was taken from Router R3. A scan of R3‘s configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（）R3show ip ospf interface briefInterface PID Area IP Address/Mask Cost State Nbrs F/CSe0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A. An a uto - cost reference - bandwidth 1000 command in router ospf modeB. An auto - cost reference - bandwidth 2000 command in router ospf modeC. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD. An auto - cost reference - bandwidth 64700 command i n router ospf mode
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E. None of the other answers is correct.
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: Gateway of last resort is 1.1.1.1 to network 2.0.0.0.Whic h of the following is most likely to have caused this output to occur on R1?（）A. R1 has been configured with an ip default- network 2.0.0.0 command.B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D. Another router has been configured with an ip default - network 2.0.0.0 command.E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterAping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.What can you conclude about router A?（）A. Only the router A loopback interface is parti cipating in the OSPF routing processB. None of the router A interfaces are participating in the OSPF routing processC. Router A is using the loopback interface IP address as its OSPF router IDD. Router A does not have any reachable OSPF neighbors
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
You are troubleshooting a WAN connection for TestKing, and on the router you execute the, debug ppp authentication command, and view the following output:What kind of handshake was used for the PPP authentication?（）A. one-wayB. two-wayC. three-wayD. No handshakes required during authenticationE. None of the above
The following was issues on router TestKingA:TestKingA show ip ospf neighborNeigbor ID PRI State Dead Time Address Interface192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1Which type of OSPF network will provide the output shown in the graphic?（）A. FDDIB. nonbroadcast multiaccessC. broadcast multi-accessD. point-to-point
You are a network technician at TestKing, Inc. You are currently troubleshooting a routing issue on the Testking1 router. You issue the show ip route command. The output from the command is displayed in the following exhibit:Which one of the following routes WILL NOT be entered into its neighboring routers routing table?（）A. R 192.168.11.0/24 [120/7] via 192.168.9.1, 00:00:03, Serial1B. C 192.168.1.0/24 is directly connected, Ethernet0C. R 192.168.8.0/24 [120/1] via 192.168.2.2, 00:00:10, Serial0D. R 192.168.5.0/24 [120/15] via 192.168.2.2, 00:00:10, Serial0E. None of the above
Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true?() A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.B. Router C will use ICMP to inform Router B that Host 2 cannot be reached.C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.D. Router C will send a Destination Unreachable message type.E. Router C will send a Router Selection message type.F. Router C will send a Source Quench message type.
Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true (Choose two.)（）。A、Router C will use ICMP to inform Host 1 that Host 2 cannot be reachedB、Router C will use ICMP to inform Router B that Host 2 cannot be reachedC、Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reachedD、Router C will send a Destination Unreachable message typeE、Router C will send a Router Selection message typeF、Router C will send a Source Quench message type
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode
The following was issues on router TestKingA: TestKingA #show ip ospf neighbor Neigbor ID PRI State Dead Time Address Interface 192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1 Which type of OSPF network will provide the output shown in the graphic?（）A、FDDIB、nonbroadcast multiaccessC、broadcast multi-accessD、point-to-point
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）A、MetricB、Administrative distanceC、Timeout (seconds)D、Prefix lengthE、Interface ID
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
You execute the following command to enable a session in resumable mode： SQL ALTER SESSION ENABLE RESUMABLE TIMEOUT 60; What is the impact of a timeout on the statements being suspended？（）A、The statements remain suspended for at least 60 seconds.B、The statements are suspended for 60 seconds and then they are executed.C、The suspended statements error out if the problem is not rectified within 60 seconds.D、The statements are automatically suspended 60 seconds after an error is received， and then attempt to execute normally again.
You issued the following statement： SQLALTER DATABASE ENABLE RESUMABLE TIMEOUT n； What will be the result of issuing the above statement？（）A、The command will not execute successfully because TIMEOUT is an invalid clause with the ALTER DATABASE ENABLE RESUMABLE command.B、 The command will not execute successfully because resumable space allocation is enabled at the session level.C、 The command will execute successfully and resumable space will be allocated at the session level.D、 The command will execute successfully and resumable space will be allocated at the instance level.
单选题The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（） B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18AThis router has set the Weight of this route to 10.BThis router's BGP table lists this route as an iBGP route.CThis router's MED has been set to 10.DThis router's BGP table lists an AS_Path length of 10 for this route.
单选题OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）AOnly the router A loopback interface is parti cipating in the OSPF routing processBNone of the router A interfaces are participating in the OSPF routing processCRouter A is using the loopback interface IP address as its OSPF router IDDRouter A does not have any reachable OSPF neighbors