多选题Your routed TCP/IP network consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. Your network uses TCP/IP as the only network protocol. You are installing 10 new Windows 2000 Professional computers. You want to enable the new computers to use NetBIOS names to connect to all shared resources as the network. You configure a TCP/IP address and a subnet mask on each new computer. Which 2 additional TCP/IP properties should you configure on each new computer？（）AThe bindings.BA DNS address.CA Gateway address.DA WINS server address.EA DHCP server address.
多选题
Your routed TCP/IP network consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. Your network uses TCP/IP as the only network protocol. You are installing 10 new Windows 2000 Professional computers. You want to enable the new computers to use NetBIOS names to connect to all shared resources as the network. You configure a TCP/IP address and a subnet mask on each new computer. Which 2 additional TCP/IP properties should you configure on each new computer？（）
A
The bindings.
B
A DNS address.
C
A Gateway address.
D
A WINS server address.
E
A DHCP server address.
参考解析
解析：
暂无解析
相关考题：
You are the administrator of your company's network. The network is configured as shown in the exhibit.You want to install Windows 2000 Professional on 10 non-PXE-compliant computers that are on the marketing segment of your network. You start one of the computers by using a RIS boot disk. However, you cannot connect to the RIS server.You verify that the existing client computers on the network can connect to network servers, including the RIS server. The network router does not support BOOTP, so existing client computers use manually configured TCP/IP addresses. You want to enable the computers to connect to the RIS server.What should you do?A．Add a computer running DHCP Relay Agent to the marketing segment.B．Add a computer running the network monitor driver to the marketing segment.C．Move the Windows 2000 Server computer running WINS to the marketing segment.D．Move the Windows 2000 Server computer running Active Directory to the marketing segment.
Ezonexam.com's network consists of Windows 2000 Professional and UNIX client computers. You install a Windows 2000 Server computer on the network. All computers that are connected to the network use TCP/IP as their only network protocol.Several laser print devices are attached to the UNIX computers. You want to enable the Windows 2000 Professional computers to print to these printers. You want to make the minimum number of configuration changes necessary to achieve this goal.What should you do?A．Install Simple TCP/IP services on the Windows 2000 Server computer. Configure printers on the Windows 2000 Server computer to print to the print device attached to the UNIX computers.B．Install Print Services for UNIX on the Windows 2000 Server computer. Configure shared printers on the Windows 2000 Server computer. Configure the UNIX computers to print to these shared printers.C．Disconnect the print devices from the UNIX computers and connect them to the Windows 2000 Server computer. Share the printers, and configure the Windows 2000 Professional computers and the UNIX computers to print to the shared printers.D．On the Windows 2000 Server computer, configure shared printers that connect to the print devices attached to the UNIX computers. Configure the Windows 2000 Professional computers to print to the shared printers on the Windows 2000 Server computer.
YouaretheadministratorofCompany.com‘sWindows2000Network.TheroutedTCP/IPnetworkthatyouadministerconsistsof10Windows2000Servercomputersand75Windows2000Professionalcomputers.AllcomputersaremembersofasingleWindows2000domainnamedCompany.com.TCP/IPistheonlynetworkprotocolusedatCompany‘soffice.Youhaverecentlyinstalled10newWindows2000Professionalcomputersandyouwanttoenablethenewcomputerstousehostnamestoconnecttosharedresourcesonthenetwork.YouconfigureaTCP/IPaddressandagatewayaddressoneachnewcomputer.Youwanttocompletetheconfigurationtoallowthecomputerstocommunicateonthenetwork.Whatshouldyoudo?（）
You are the administrator for Ezonexam.com's network.Your network includes Windows 2000 Professional client computers, Windows NT Workstation 4.0 client computers, Windows 98 client computers, and UNIX client computers. Users of the Windows operating systems store files on shared folders on a Windows 2000 Server computer named FileServ.You want to make the shared folders on FileServ available to the UNIX computers.What should you do?A．Install and configure Network File System (NFS) on FileServ.B．Configure data volumes on FileServ to be FAT volumes.C．Disable Server Message Block (SMB) signing on FileServ.D．Install Simple TCP/IP Services on FileServ.
Your routed TCP/IP network consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. Your network uses TCP/IP as the only network protocol. You are installing 10 new Windows 2000 Professional computers. You want to enable the new computers to use NetBIOS names to connect to all shared resources as the network. You configure a TCP/IP address and a subnet mask on each new computer. Which 2 additional TCP/IP properties should you configure on each new computer？（）A、The bindings.B、A DNS address.C、A Gateway address.D、A WINS server address.E、A DHCP server address.
You are the administrator of WXYZ.com Incorporation. Your company’s network consists of Windows 2000 Professional clients and Windows 2000 Servers. Users have started reporting that the network performance has degraded in recent times. Most of the Windows 2000 Professional clients on your network use the TCP/IP protocol to communicate with the Server. You want to increase network performance. Where do you change the binding order？（）A、Windows 2000 Server Network Binding Server TCP/IP on the top.B、Windows 2000 Server Network Binding Workstation TCP/IP on the top.C、Windows 2000 Professional Network Binding Server TCP/IP on the top.D、Windows 2000 Professional Network Binding Server TCP/IP on the bottom.E、Windows 2000 Professional Network Binding Workstation TCP/IP on the top.F、Windows 2000 Professional Network Binding Workstation TCP/IP on thebottom.
You are the administrator of a Windows 2000 network. The network consists of a Windows 2000 domain named ExamSheet.net. You install Windows 2000 Professional on a new computer named ES1 and configure the TCP/IP settings to have a static IP address. You plan to join ES1 to the ExamSheet.net domain. You configure two DNS server addresses in the TCP/IP properties. The first DNS server address is for a DNS server hosted by your ISP, the second DNS server address is for a DNS server authoritative for the ExamSheet.net domain. When you attempt to join ES1 to the domain, you are unable to do so. You can successfully PINGthe IP address of each DNS server from ES1. You want ES1 to be able to join the tesking.com domain. What should you do? （）A、Delete the second DNS server entry.B、Delete the first DNS server entry.C、Add an A （host） record for the computer to the appropriate DNS zone.D、Configure the computer toObtain an IP address automatically.
The network at Company Ltd. consists of one Windows NT Server 4.0 domain and 35 Windows 2000Professional computers. The Company network consists of five interconnected TCP/IP subnets. All of thecomputers use TCP/IP as the only network protocol.You are adding 15 Windows 2000 Professional computers to the network. You want to enable theWindows 2000 Professional computers to resolve NetBIOS names to TCP/IP addresses.What should you do？ （）A、Install a DHCP server. Configure each computer to use DHCP. B、Install a WINS server. Configure each computer to use WINS. C、Create a Lmhosts.sam file on each computer. Add an entry containing the TCP/IP address and NetBIOS name for each computer on the network. D、Create a Hosts.sam file on each computer. Add an entry containing the TCP/IP address and NetBIOS name for each computer on the network.
You want to prevent a Windows 2000 Professional computer named Payroll5 from communicating on your network with Windows NT 4.0， Windows 95， and Windows 98 computers. You want to enable the payroll5 computer to communicate on your network with other Windows 2000 computers only. What should you do？（）A、Close all NetBIOS ports in the advanced TCP/IP options of Payroll5.B、Import the Hisecws.inf security template to payroll5.C、Disable access this computer from network in the local security policy settings for payroll5.D、Clear all WINS client settings on payroll5.
Your network consists of a single IPv4 subnet. The subnet contains 20 computers that run Windows 7. Youadd a new computer named Computer1 to the subnet. You discover that Computer1 has an IP address of169.254.34.12. You cannot connect to other computers on the network. Other computers on the networkcan connect to each other. You need to ensure that you can connect to all computers on the network. What should you do?（）A、Turn off Windows Firewall.B、Run Ipconfig.exe /renew.C、Configure a static TCP/IP address.D、Run Netsh.exe interface ipv4 install.
Your network administrator has assigned you an IP address of 192.168.0.20 with subnet mask of 255.255.255.0.Your network is running in pure Windows 2000 domain. What else should know in order to join your computer to the Windows 2000 domain. （）A、 Address of DHCP server.B、 Address of WINS server.C、 Address of DNS server.D、 Address of default gateway
You are the network administrator for Company. Company has recently upgraded its network to a 100Mbps standard and you are now in the process of removing all the old adapter and installing a new Token Ring network adapter into the Windows 2000 Professional computer. On the first computer you install the new hardware and configure the static TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart the computer, however, you cannot access the network. You try to ping your network adapter's TCP/IP address locally. You receive the following error message: "Request timed out." You want to enable the computer to communicate on the new network. What should you do? （）A、Enable DHCP in the TCP/IP properties.B、Replace the Token Ring network adapter with an Ethernet network adapter.C、Configure a different TCP/IP address on the same subnet.D、Configure a valid DNS Server in the TCP/IP properties.
Most of the Windows 2000 Professional clients on your network use the TCP/IP Protocol to communicate with Server. You want to increase network performance. Where do you change the binding order of your protocols？ （）A、On the Windows 2000 Server， set TCP/IP for the Server service at the top.B、On the Windows 2000 Professional computers， set TCP/IP for the Workstation service at the top.C、On the Windows 2000 Server， set TCP/IP for the Workstation service at the top.D、On the Windows 2000 Professional computers， set TCP/IP for the Server service at the top.
You are the administrator of Etechsol.com Enterprises. Your company consists of a small 20-user network. Management has decided to upgrade all computers to Windows 2000. After having a closer examination of your company’s network, you realize that only half of the network interface cards are Net PC compliant. You decide to create Windows 2000 remote boot floppies. What executable is used for creating RIS boot disks for non-PXE compliant clients?（）A、RBFG*EXEB、RIPREP*EXEC、RIS*EXED、RISPXE*EXEE、RISBOO*EXE
多选题You are the administrator of Company.com's Windows 2000 Network. The routed TCP/IP network that you administer consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. All computers are members of a single Windows 2000 domain named Company.com. TCP/IP is the only network protocol used at Company's office. You have recently installed 10 new Windows 2000 Professional computers and you want to enable the new computers to use host names to connect to shared resources on the network. You configure a TCP/IP address and a gateway address on each new computer. You want to complete the configuration to allow the computers to communicate on the network. What should you do?（）AConfigure a DNS suffix.BConfigure a subnet mask.CConfigure an LMHOSTS file.DConfigure an Interface metric.EConfigure at least one DNS address.
单选题You want to connect your Windows 2000 Professional computer to multiple TCP/IP subnets on your company’s network. Your computer currently has an ISA network adapter installed. You install a second ISA network adapter. After you restart your computer， you notice that the second ISA network adapter is not functioning. What should you do？（）ASet the driver signing option to block.BSet the driver signing option to ignore.CIn the computer’s BIOS， reserve an unused IRQ for ISA devices.DIn the Device Manager， configure the second ISA network adapter to use an unused IRQ.
单选题You are the network administrator for Company. Your network consists of one Windows NT Server 4.0 domain and 35 Windows 2000 Professional computers. The network consists of five interconnected TCP/IP subnets. All of the computers use TCP/IP as the only network protocol. You are adding 15 Windows 2000 Professional computers to the network. You configure each of the new computers to use DHCP. The computers can communicate with each other but are unable to communicate outside their own subnet. You run the ipconfig command to examine the UP address on one of the new computers. The IP address is 169.254.101.72 You want to enable the Windows 2000 Professional computers to communicate outside their own subnet. What should you do?（）AInstall a DHCP server.BInstall a WINS server. Configure each computer to use WINS.CCreate an Lmhost file on each computer.DCreate a Hosts file on each computer.
单选题You are the administrator of WXYZ.com Incorporation. Your company’s network consists of Windows 2000 Professional clients and Windows 2000 Servers. Users have started reporting that the network performance has degraded in recent times. Most of the Windows 2000 Professional clients on your network use the TCP/IP protocol to communicate with the Server. You want to increase network performance. Where do you change the binding order？（）AWindows 2000 Server Network Binding Server TCP/IP on the top.BWindows 2000 Server Network Binding Workstation TCP/IP on the top.CWindows 2000 Professional Network Binding Server TCP/IP on the top.DWindows 2000 Professional Network Binding Server TCP/IP on the bottom.EWindows 2000 Professional Network Binding Workstation TCP/IP on the top.FWindows 2000 Professional Network Binding Workstation TCP/IP on thebottom.
单选题You want to configure your Windows 2000 Professional computer to remotely access your company’s Windows 2000 routing and remote access server. You configure a VPN connection. For security purposes， you configure the VPN connection to use MS-CHAP v2 only and to require encryption. You also configure TCP/IP to obtain an IP address automatically， to enable IPSec， and to set IPSec to secure server. When you try to connect， you receive the following error message， “The encryption attempt failed because no valid certificate was found.” What should you do to connect to the server？ （）AEnable the VPN connection to use MS-CHAP.BChange the data encryption setting to Optional Encryption.CSpecify a TCP/IP address in the network properties.DChange the IPSec policy setting to Client.
单选题Your network administrator has assigned you an IP address of 192.168.0.20 with subnet mask of 255.255.255.0.Your network is running in pure Windows 2000 domain. What else should know in order to join your computer to the Windows 2000 domain. （）A Address of DHCP server.B Address of WINS server.C Address of DNS server.D Address of default gateway
单选题You are the network administrator for ExamSheet. Your network consists of one Windows NT Server 4.0 domain and 35 Windows 2000 Professional computers. The network consists of five interconnected TCP/IP subnets. All of the computers use TCP/IP as the only network protocol. You are adding 15 Windows 2000 Professional computers to the network. You configure each of the new computers to use DHCP. The computers can communicate with each other but are unable to communicate outside their own subnet. You run the ipconfig command to examine the IP address on one of the new computers. The IP address is 169.254.101.72 You want to enable the Windows 2000 Professional computers to communicate outside their own subnet. What should you do？（）AInstall a DHCP server.BInstall a WINS server. Configure each computer to use WINS.CCreate an Lmhost file on each computer.DCreate a Hosts file on each computer.
多选题You are the administrator of Company.com’s Windows 2000 Network. Your routed TCP/IP network consists of 10 Windows 2000 Server computers and 75 Windows 2000 Professional computers. All computers are in the Company.com domain. Your network uses TCP/IP as the only network protocol. You are installing 10 new Windows 2000 Professional computers. You want to enable the new computers to use host names to connect to shared resources on the network. You configure a TCP/IP address, a gateway address and a subnet mask on each new computer. You want to complete the configuration to allow the computers to communicate on the network. What should you do?（）AConfigure a HOSTS file.BConfigure a LMHOSTS file.CConfigure a WINS server database.DConfigure a DHCP server address.EConfigure at least one DNS address.
单选题Your Company upgrades its network to 100 Mbps. You remove the old network adapter and install a new 10/100 Mbps network adapter into a Windows 2000 Professional computer. You configure the TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart eh computer, however, you cannot access the network. You try to ping your network adapter’s TCP/IP address locally. You receive the following error message. “Request timed out.” Next, you try to ping 127.0.0.1 and receive the same error message. What must you do?（）AConfigure a different TCP/IP addressBEnable DHCP in the TCP/IP propertiesCEnable DNS in the TCP/IP propertiesDConfigure the network adapter to run at 100 Mbps onlyEReplace the network adapter.
单选题You are the administrator of a Windows 2000 network. You install Windows 2000 Professional on a new computer and configure the TCP/IP settings to have a static IP address. While testing network connectivity from the new computer, you discover an error in the DNS server address that is configured in the TCP/IP settings. You configure the correct DNS server address, which is 10.1.1.5. However, you are still unable to successfully connect to network resources by name. You run the IPconfig/all command. The results indicate that the DNS server address is now configured as 0.0.0.0 You need to ensure that the computer can connect to network resources by name. What should you do?（）AStop and restart the DNS Client service.BAdd 10.1.1.5 to the DNS server list on the TCP/IP Advanced Properties tab.CAdd an A （host） record for the computer to the DNS server’s zone file.DConfigure your DHCP server to have a DNS server address of 10.1.1.5.
单选题Most of the Windows 2000 Professional clients on your network use the TCP/IP Protocol to communicate with Server. You want to increase network performance. Where do you change the binding order of your protocols？ （）AOn the Windows 2000 Server， set TCP/IP for the Server service at the top.BOn the Windows 2000 Professional computers， set TCP/IP for the Workstation service at the top.COn the Windows 2000 Server， set TCP/IP for the Workstation service at the top.DOn the Windows 2000 Professional computers， set TCP/IP for the Server service at the top.