单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）AABRBASBRCinternal routerDbackbone router
单选题
What type of OSPF router is responsible for redistributing routes into OSPF?（）
A
ABR
B
ASBR
C
internal router
D
backbone router
参考解析
解析：
暂无解析
相关考题：
Which router translates the Type 7 LSAs into Type 5 LSAs, according to RFC 1587 (OSPF NSSAOption) in an OSPF NSSA with more than one ABR?() A. The router receiving the route translates the Type 7 LSA into a Type 5 LSA.B. The ABR with the lowest router ID translates all Type 7 LSAs into Type 5 LSAs.C. The ABR with the highest router ID translates all Type 7 LSAs into Type 5 LSAs.D. All ABRs translate the Type 7 LSAs into Type 5 LSAs depending on which one has the lowest cost to the route.
Which OSPF router type summarizes network advertisements from one OSPF area into another?() A.AB.BC.CD.D
What type of OSPF router is responsible for redistributing routes into OSPF?() A. ABRB. ASBRC. internal routerD. backbone router
Router R1 sets a route tag for subnet 10.1.1.0／24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?() A. Kilobits/seconDB. Tens of microsecondsC. CostD. Hop countE. No unit is assigneD
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A. ip ospf network broadcastB. ip ospf network non - broadcastC. ip ospf network point - to - multipointD. ip ospf network point - to - multipoint non - broadcast
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）A. type 1 Router LSAB. type 2 Network LSAC. type 3 Network Summary LSAD. type 4 ASBR Summary LSAE. type 5 AS External LSAF. type 7 NSSA External LSA
What will happen after redistributing other routing protocol routes into OSPF? () A. miss the metric option in the redistribute command.B. misconfigure the metric- type option in t he redistribute command to type - 1.C. miss the subnet option in the redistribute command.D. miss the tag option in the redistribute command.
Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Which is true about OSPF router－id?() A.It is used for type 1 router LSAB.Highest IP address of the loopback is usedC.router-id needs to be matched on ospf neighborsD.router-id is 16 bit
Which is true about OSPF router-id?（）A、It is used for type 1 router LSAB、Highest IP address of the loopback is usedC、router-id needs to be matched on ospf neighborsD、router-id is 16 bit
Your network trainee asks you, in the context of IPv6 and OSPF, what best des cribes a type 9 LSA? What should you tell her?（）A、Link LSAB、Interarea prefix LSA for ABRsC、Router LSAD、Switch LSAE、Intra - area prefix LSAF、None of the above
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A、ip ospf network broadcastB、ip ospf network non - broadcastC、ip ospf network point - to - multipointD、ip ospf network point - to - multipoint non - broadcast
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）A、Only the router A loopback interface is parti cipating in the OSPF routing processB、None of the router A interfaces are participating in the OSPF routing processC、Router A is using the loopback interface IP address as its OSPF router IDD、Router A does not have any reachable OSPF neighbors
单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）AABRBASBRCinternal routerDbackbone router
单选题Which router is doing LSA type 7 to type 5 translation，and why？（）ABoth RTA and RTB will do LSA7/5 translation，since they are both NSSA ABRsBRTA will do LSA7/5 translation，since it has the lower router IDCRTB will do LSA7/5 translation，since it has the higher router IDDThe redistributing router will do LSA7/5 translation，since it is within the NSSA
单选题Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?（）Aip ospf network broadcastBip ospf netw ork non - broadcastCip ospf network point - to - multipointDip ospf network point - to - multipoint non - broadcast
单选题Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）AKilobits/seconDBTens of microsecondsCCostDHop countENo unit is assigneD
单选题OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）AOnly the router A loopback interface is parti cipating in the OSPF routing processBNone of the router A interfaces are participating in the OSPF routing processCRouter A is using the loopback interface IP address as its OSPF router IDDRouter A does not have any reachable OSPF neighbors
单选题Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1ANo routes are redistributed because a route cannot be both E1 and E2.BOnly OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.CInside the OSPF 2 domain, any formerly E2 routes will become E1 routes.DRoutes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
单选题What is the function of the helper router during a restart event in OSPF?（）ASends Rapid Hellos to the restarting router.BMaintains Adjancency with restarting router.CSends periodic DD packets to the restarting router.DFloods Type 9 LSAs to all routers indicating a restarting event.
单选题Which router translates the Type 7 LSAs into Type 5 LSAs, according to RFC 1587 (OSPF NSSAOption) in an OSPF NSSA with more than one ABR?（）AThe router receiving the route translates the Type 7 LSA into a Type 5 LSA.BThe ABR with the lowest router ID translates all Type 7 LSAs into Type 5 LSAs.CThe ABR with the highest router ID translates all Type 7 LSAs into Type 5 LSAs.DAll ABRs translate the Type 7 LSAs into Type 5 LSAs depending on which one has the lowest cost to the route.
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
多选题Which is true about OSPF router-id?（）AIt is used for type 1 router LSABHighest IP address of the loopback is usedCrouter-id needs to be matched on ospf neighborsDrouter-id is 16 bit
单选题Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)AR1 is the router that redistributed the routeBR1's metric to reach subnet 10.2.2.0/24 is 64CThe route was redistributed on a router that has a router ospf 1 command configuredDR1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF