A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?() A. All defined VLANs are allowed on the trunk by default.B. Each VLAN, or VLAN range, that is specified with the switchport mode command.C. Each VLAN, or VLAN range, that is specified with the vtp domain command.D. Each VLAN, or VLAN range, that is specified with the vlan database command.
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?()
A. All defined VLANs are allowed on the trunk by default.
B. Each VLAN, or VLAN range, that is specified with the switchport mode command.
C. Each VLAN, or VLAN range, that is specified with the vtp domain command.
D. Each VLAN, or VLAN range, that is specified with the vlan database command.
相关考题：
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?A．All defined VLANs are allowed on the trunk by default.B．Each VLAN, or VLAN range, that is specified with the switchport mode command.C．Each VLAN, or VLAN range, that is specified with the vtp domain command.D．Each VLAN, or VLAN range, that is specified with the vlan database command.E．None of the above
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?A. No VLANsB. Only the VLANs that are specified when creating the trunkC. Only VLANs 1-64D. All VLANsE. All VLAN's except VLAN 1F. None of the above
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).A．You must set each end of the trunk line to IEEE 802.1e encapsulation.B．You must set the same VTP management domain name on both switches.C．You must set all ports on the two switches as access ports.D．You must configure one of the switches as a VTP server.E．You must use a rollover cable to connect the two switches.
Using a policy with the policy－rematch flag enabled, what happens to the existing and new sessions when you change the policy action from permit to deny?() A. The new sessions matching the policy are denied. The existing sessions are dropped.B. The new sessions matching the policy are denied. The existingsessions, not being allowed tocarry any traffic, simply timeout.C. The new sessions matching the policy might be allowed through if they match another policy. The existing sessions are dropped.D. The new sessions matching the policy are denied. The existing sessions continue until they are completed or their time.
The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?A．Switch(config)# switchport trunk encapsulation islB．Switch(config)# switchport trunk encapsulation ietfC．Switch(config-if)# switchport trunk encapsulation islD．Switch(config-if)# switchport trunk encapsulation ietfE．Switch(config-if)# switchport trunk encapsulation dot1q
A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?() A. The VLAN must be createdB. The VLAN must be namedC. An IP address and subnet mask must be configured for the new VLAND. The desired ports must be added to the new VLANE. The VLAN must be added to the existing VTP Domain
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。 A.no VLANsB.all VLANsC.only VLANs 1 - 64D.only the VLANs that are specified when creating the trunk
A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?（）A、The VLAN must be createdB、The VLAN must be namedC、An IP address and subnet mask must be configured for the new VLAND、The desired ports must be added to the new VLANE、The VLAN must be added to the existing VTP Domain
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）A、The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.B、The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C、The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.D、The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link（）。A、By default, all defined VLANs are allowed on the trunk.B、Each single VLAN, or VLAN range, must be specified with the switchport mode command.C、Each single VLAN, or VLAN range, must be specified with the vtp domain command.D、Each single VLAN, or VLAN range, must be specified with the vlan database command.
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link（）。A、no VLANsB、all VLANsC、only VLANs 1 - 64D、only the VLANs that are specified when creating the trunk
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）A、Because the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.B、As a VTP server， the new switch deleted all VLANs of the network.C、Erasing VLANs increases the VTP configuration revision.D、Since the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?（）A、You must set each end of the trunk line to IEEE 802.1e encapsulation.B、You must set the same VTP management domain name on both switches.C、You must set all ports on the two switches as access ports.D、You must configure one of the switches as a VTP server.E、You must use a rollover cable to connect the two switches.
Using a policy with the policy-rematch flag enabled, what happens to the existing and new sessionswhen you change the policy action from permit to deny? （）A、The new sessions matching the policy are denied. The existing sessions are dropped.B、The new sessions matching the policy are denied. The existing sessions, not being allowed to carry any traffic, simply timeout.C、The new sessions matching the policy might be allowed through if they match another policy. The existing sessions are dropped.D、The new sessions matching the policy are denied. The existing sessions continue until they are completed or their timeout is reached.
Using a policy with the policy-rematch flag enabled， what happens to the existing and newsessions when you change the policy action from permit to deny？（）A、The new sessions matching the policy are denied. The existing sessions are dropped.B、The new sessions matching the policy are denied. The existing sessions， not being allowed to carry any traffic， simply timeout.C、The new sessions matching the policy might be allowed through if they match another policy. The existing sessions are dropped.D、The new sessions matching the policy are denied. The existing sessions continue until they are completed or their timeout is reached.
单选题You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）ASwitch(config)# switchport trunk encapsulation islBSwitch(config)# switchport trunk encapsulation ietfCSwitch(config-if)# switchport trunk encapsulation islDSwitch(config-if)# switchport trunk encapsulation ietfESwitch(config-if)# switchport trunk encapsulation dot1q
单选题A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）AThe new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.BThe configuration revision of the new switch was higher than the configuration revision of the production VTP domain.CThe link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.DThe ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
单选题An administrator has an existing HMC and POWER6 570 connected to a network switch. The administrator is planning to install two POWER6 570s with a dedicated HMC. Which infrastructure is required for the new HMC？（）AAn additional switch for the new HMc BAsynchronous adapters on the new HMcCThe two 570 servers are directly connected to the new HMc DOne 570 is directly connected to the new HMC and the other is directly connected to the existing HMc
单选题A customer wants to migrate their existing cluster onto new POWER6 hardware， and in addition requires thecluster to be migrated from PowerHA version 5.3 to 5.5. Given that AIX 6.1 and PowerHA 5.5 filesets arealready installed in the new hardware， which of the following methods would allow the customer to maintaintheir current cluster configuration？（）AAdd the new nodes to the existing cluster， and perform a rolling migration and remove the original nodesfrom the clusterBAdd the new nodes to the existing cluster， and perform a non-disruptive upgrade and remove the originalnodes from the cluster.CCreate a snapshot of the existing cluster and apply the snapshot to the new cluster. Start cluster serviceson the new cluster and stop the original clusterDCreate a snapshot of the existing cluster and apply the snapshot to the new cluster. Stop cluster serviceson the original cluster and start on the new cluster
单选题When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link?（）Ano VLANsBall VLANsConly VLANs 1 - 64Donly the VLANs that are specified when creating the trunk
多选题A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?（）AThe VLAN must be createdBThe VLAN must be namedCAn IP address and subnet mask must be configured for the new VLANDThe desired ports must be added to the new VLANEThe VLAN must be added to the existing VTP Domain
单选题Using a policy with the policy-rematch flag enabled, what happens to the existing and new sessionswhen you change the policy action from permit to deny? （）AThe new sessions matching the policy are denied. The existing sessions are dropped.BThe new sessions matching the policy are denied. The existing sessions, not being allowed to carry any traffic, simply timeout.CThe new sessions matching the policy might be allowed through if they match another policy. The existing sessions are dropped.DThe new sessions matching the policy are denied. The existing sessions continue until they are completed or their timeout is reached.
单选题An administrator has an existing HMC and POWER6 570 connected to a network switch. The administrator is planning to install two POWER6 570s with a dedicated HMC. Which infrastructure is required for the new HMC?（）AAn additional switch for the new HMCBAsynchronous adapters on the new HMCCThe two 570 servers are directly connected to the new HMCDOne 570 is directly connected to the new HMC and the other is directly connected to the existing HMC