When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。 A.no VLANsB.all VLANsC.only VLANs 1 - 64D.only the VLANs that are specified when creating the trunk
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。
A.no VLANs
B.all VLANs
C.only VLANs 1 - 64
D.only the VLANs that are specified when creating the trunk
相关考题：
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?A．All defined VLANs are allowed on the trunk by default.B．Each VLAN, or VLAN range, that is specified with the switchport mode command.C．Each VLAN, or VLAN range, that is specified with the vtp domain command.D．Each VLAN, or VLAN range, that is specified with the vlan database command.E．None of the above
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?A. No VLANsB. Only the VLANs that are specified when creating the trunkC. Only VLANs 1-64D. All VLANsE. All VLAN's except VLAN 1F. None of the above
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?A．Switch(config)# switchport trunk encapsulation islB．Switch(config)# switchport trunk encapsulation ietfC．Switch(config-if)# switchport trunk encapsulation islD．Switch(config-if)# switchport trunk encapsulation ietfE．Switch(config-if)# switchport trunk encapsulation dot1q
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?() A. All defined VLANs are allowed on the trunk by default.B. Each VLAN, or VLAN range, that is specified with the switchport mode command.C. Each VLAN, or VLAN range, that is specified with the vtp domain command.D. Each VLAN, or VLAN range, that is specified with the vlan database command.
Which three statements about VTP features are true?（）A、When properly configured,VTP minimizes VLAN misconfigurations and configuration inconsistenciesB、Each broadcast domain on a switch can have its own unique VTP domainC、VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured.D、When properly configured,VTP maintains VLAN configuration consistency and accelerates trunk link negotiation.E、VTP pruning is used to increase available bandwidth in trunk linksF、Client,server,and transparent are valid VTP modesG、To configure a switch to be part of two VTP domains,each domain must have its own passwords
Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）A、 The interface actively attempts to convert the link to a trunk link.B、 The interface is put into permanent trunking mode but prevented from generating DTP frames. C、 The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.D、 The interface is put into a passive mode， waiting to convert the link to a trunk link. E、 None of the other alternatives apply
You have configured voice VLANs on Catalyst switch R1. Which two statements are true about the operation of voice VLANs on this device？ （）A、 When the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port.B、 Enabling voice VLANs enables the switch to create multiple queues for traffic that is entering a port.C、 When voice VLANs are configured on a trunk link， UplinkFast must also be enabled.D、 Voice VLANs are configured to enable the switch to forward frames marked with the proper CoS values over separate physical links.E、 Enabling voice VLANs enables the switch to forward frames with a specific 802.1P marking.
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link（）。A、By default, all defined VLANs are allowed on the trunk.B、Each single VLAN, or VLAN range, must be specified with the switchport mode command.C、Each single VLAN, or VLAN range, must be specified with the vtp domain command.D、Each single VLAN, or VLAN range, must be specified with the vlan database command.
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）A、The switch must be configured with an IP address, subnet mask, and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link（）。A、no VLANsB、all VLANsC、only VLANs 1 - 64D、only the VLANs that are specified when creating the trunk
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1， which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner （R2） and become a trunk？ （）A、 AutoB、 NegotiateC、 DesignateD、 No negotiate
What is the purpose of the cisco Vlan Trunking protocol?（）A、to provide a mechanism to dynamically assign vlan membership to switch portsB、to allow traffic to be carried from multiple vlans over a single link between switchesC、to allow native vlan information to be carried over a trunk linkD、to provide a mechanism to manually assign vlan membership to switch portsE、to allow for managing the additions,deletions,and changes of vlans between switchs
On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）A、a router with subinterfaces configured on the physical interface that is connected to the switchB、a router with an IP address on the physical interface connected to the switchC、a switch with an access link that is configured between the switchesD、a switch with a trunk link that is configured between the switches
单选题You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）ASwitch(config)# switchport trunk encapsulation islBSwitch(config)# switchport trunk encapsulation ietfCSwitch(config-if)# switchport trunk encapsulation islDSwitch(config-if)# switchport trunk encapsulation ietfESwitch(config-if)# switchport trunk encapsulation dot1q
单选题Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）A The access link needs to be configured in multiple VLANs.B The link between the switches is configured in the wrong VLAN.C The link between the switches needs to be configured as a trunk.D VTP is not configured to carry VLAN information between the switches.E Switch IP addresses must be configured in order for traffic to be forwarded between the switches
单选题Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。Aa switch with a trunk link that is configured between the switchesBa router with an IP address on the physical interface that is connected to the switchCa switch with an access link that is configured between the switchesDa router with subinterfaces configured on the physical interface that is connected to the switch
多选题You have configured voice VLANs on Catalyst switch R1. Which two statements are true about the operation of voice VLANs on this device？ （）AWhen the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port.BEnabling voice VLANs enables the switch to create multiple queues for traffic that is entering a port.CWhen voice VLANs are configured on a trunk link， UplinkFast must also be enabled.DVoice VLANs are configured to enable the switch to forward frames marked with the proper CoS values over separate physical links.EEnabling voice VLANs enables the switch to forward frames with a specific 802.1P marking.
单选题If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1， which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner （R2） and become a trunk？ （）A AutoB NegotiateC DesignateD No negotiate
多选题When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?（）ABlockingBAutoCDesirableDOnETransparentFLearning
单选题When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link?（）Ano VLANsBall VLANsConly VLANs 1 - 64Donly the VLANs that are specified when creating the trunk
单选题On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）Aa router with subinterfaces configured on the physical interface that is connected to the switchBa router with an IP address on the physical interface connected to the switchCa switch with an access link that is configured between the switchesDa switch with a trunk link that is configured between the switches
单选题What is the purpose of the cisco Vlan Trunking protocol?（）Ato provide a mechanism to dynamically assign vlan membership to switch portsBto allow traffic to be carried from multiple vlans over a single link between switchesCto allow native vlan information to be carried over a trunk linkDto provide a mechanism to manually assign vlan membership to switch portsEto allow for managing the additions,deletions,and changes of vlans between switchs