A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?() A. The VLAN must be createdB. The VLAN must be namedC. An IP address and subnet mask must be configured for the new VLAND. The desired ports must be added to the new VLANE. The VLAN must be added to the existing VTP Domain
A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?()
A. The VLAN must be created
B. The VLAN must be named
C. An IP address and subnet mask must be configured for the new VLAN
D. The desired ports must be added to the new VLAN
E. The VLAN must be added to the existing VTP Domain
相关考题：
Which of the following steps are necessary in order to add a new VLAN to the Ezonexam switched network? (Select all that apply)A．Create the VLAN.B．Name the VLAN.C．Configure an IP address for the VLAN.D．Add the desired ports to the new VLAN.E．Add the VLAN to the VTP domain.
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?A．All defined VLANs are allowed on the trunk by default.B．Each VLAN, or VLAN range, that is specified with the switchport mode command.C．Each VLAN, or VLAN range, that is specified with the vtp domain command.D．Each VLAN, or VLAN range, that is specified with the vlan database command.E．None of the above
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named EZONEXAM. Which of the following need to be completed for the creation of this new VLAN? (Select all that apply)A. The EZONEXAM VLAN must be created.B. The desired ports must be added to the new EZONEXAM VLAN.C. The EZONEXAM VLAN must be added to all of the domains.D. The EZONEXAM VLAN must be named.E. An IP address must be configured for the EZONEXAM VLAN.F. None of the above. VLAN creations are automatic.
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?() A. All defined VLANs are allowed on the trunk by default.B. Each VLAN, or VLAN range, that is specified with the switchport mode command.C. Each VLAN, or VLAN range, that is specified with the vtp domain command.D. Each VLAN, or VLAN range, that is specified with the vlan database command.
Which of the following steps are necessary in order to add a new VLAN to a switched network?() A. Create the VLAN.B. Name the VLAN.C. Configure an IP address for the VLAN.D. Add the desired ports to the new VLAN.E. Add the VLAN to the VTP domain.
You are an administrator of a switched network and your goal is to reduce some of the administrative overhead on your network. You plan on achieving this by configuring a new VLAN for each department in your network. However, you need to share the VLAN information across numerous switches throughout your network. Which of the following would allow you accomplish this?（）A、STPB、GVRPC、SNMPD、VTPE、DHCP
Which of the following steps are necessary in order to add a new VLAN to a switched network?（）A、Create the VLAN.B、Name the VLAN.C、Configure an IP address for the VLAN.D、Add the desired ports to the new VLAN.E、Add the VLAN to the VTP domain.
A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?（）A、More collision domains will be created.B、IP address utilization will be more efficient.C、More bandwidth will be required than was needed previously.D、An additional broadcast domain will be created.
A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?（）A、The VLAN must be createdB、The VLAN must be namedC、An IP address and subnet mask must be configured for the new VLAND、The desired ports must be added to the new VLANE、The VLAN must be added to the existing VTP Domain
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link（）。A、By default, all defined VLANs are allowed on the trunk.B、Each single VLAN, or VLAN range, must be specified with the switchport mode command.C、Each single VLAN, or VLAN range, must be specified with the vtp domain command.D、Each single VLAN, or VLAN range, must be specified with the vlan database command.
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）A、The switch must be configured with an IP address,subnet mask,and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch port.F、The switch must be fully configured as an SNMP agent.
You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan？ （）A、Verify that trunked links are configured to allow the VLAN traffic.B、Verify that the switch is configured to allow for trunking on the switch ports.C、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.D、Verify that different native VLANs exist between two switches for security purposes.
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）A、The switch must be configured with an IP address, subnet mask, and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named TESTKING. Which of the following need to be completed for the creation of this new VLAN?（）A、The TESTKING VLAN must be created.B、The desired ports must be added to the new TESTKING VLAN.C、The TESTKING VLAN must be added to all of the domains.D、The TESTKING VLAN must be named.E、An IP address must be configured for the TESTKING VLAN.F、None of the above. VLAN creations are automatic.
Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）A、Because the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.B、As a VTP server， the new switch deleted all VLANs of the network.C、Erasing VLANs increases the VTP configuration revision.D、Since the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?（）A、You must set each end of the trunk line to IEEE 802.1e encapsulation.B、You must set the same VTP management domain name on both switches.C、You must set all ports on the two switches as access ports.D、You must configure one of the switches as a VTP server.E、You must use a rollover cable to connect the two switches.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
A storage specialist needs to create a new host connection using the DSCLI. Which of the following parameters identifies the host（）A、hosttypeB、volume groupC、ioportsD、WWPN
单选题You are an administrator of a switched network and your goal is to reduce some of the administrative overhead on your network. You plan on achieving this by configuring a new VLAN for each department in your network. However, you need to share the VLAN information across numerous switches throughout your network. Which of the following would allow you accomplish this?（）ASTPBGVRPCSNMPDVTPEDHCP
多选题Which of the following steps are necessary in order to add a new VLAN to a switched network?（）ACreate the VLAN.BName the VLAN.CConfigure an IP address for the VLAN.DAdd the desired ports to the new VLAN.EAdd the VLAN to the VTP domain.
多选题A new VLAN needs to be created for an existing network. Which of the following are the minimum tasks that must be accomplished in order to create the new VLAN?（）AThe VLAN must be createdBThe VLAN must be namedCAn IP address and subnet mask must be configured for the new VLANDThe desired ports must be added to the new VLANEThe VLAN must be added to the existing VTP Domain
单选题You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）AVerify that different native VLANs exist between two switches for security purposes.BVerify that the VLAN was added on all switches with the use of the show vlan command. CVerify that the switch is configured to allow for trunking on the switch ports.DVerify that each switch port has the correct IP address space assigned to it for the new VLAN.
单选题A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?（）AMore collision domains will be created.BIP address utilization will be more efficient.CMore bandwidth will be required than was needed previously.DAn additional broadcast domain will be created.
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）AThe switch must be configured with an IP address, subnet mask, and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch
单选题Which one of the following protocols allows the information about the configuration of a new VLAN to be distributed across entire switched network?（）ASTPBVTPCEIGRPDSNMPECDPFNone of the above