When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?()A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link?()
- A、All defined VLANs are allowed on the trunk by default.
- B、Each VLAN, or VLAN range, that is specified with the switchport mode command.
- C、Each VLAN, or VLAN range, that is specified with the vtp domain command.
- D、Each VLAN, or VLAN range, that is specified with the vlan database command.
相关考题:
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?A. No VLANsB. Only the VLANs that are specified when creating the trunkC. Only VLANs 1-64D. All VLANsE. All VLAN's except VLAN 1F. None of the above
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?A.Switch(config)# switchport trunk encapsulation islB.Switch(config)# switchport trunk encapsulation ietfC.Switch(config-if)# switchport trunk encapsulation islD.Switch(config-if)# switchport trunk encapsulation ietfE.Switch(config-if)# switchport trunk encapsulation dot1q
Which commands, when used together, would create an 802.1Q link?() A. Switch(vlan)# mode trunkB. Switch(config)# switchport access mode trunkC. Switch(config-if)# switchport mode trunkD. Switch(config-if)# switchport trunk encapsulation dot1qE. Switch(config)# switchport access mode 1F. Switch(vlan)# trunk encapsulation dot1q
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?() A. All defined VLANs are allowed on the trunk by default.B. Each VLAN, or VLAN range, that is specified with the switchport mode command.C. Each VLAN, or VLAN range, that is specified with the vtp domain command.D. Each VLAN, or VLAN range, that is specified with the vlan database command.
VLAN Tagging, also known as Frame Tagging, is a method developed by Cisco to help identify packets travelling through trunk links. When an Ethernet frame traverses a trunk link, a special VLAN tag is added to the frame and sent across the trunk link .How does ERS use the VLAN tag?()A. provide service internetworkingB. support transparency for Layer 2 framesC. indicate destination as a connection identifierD. map to the DLCI in service internetworking
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。 A.no VLANsB.all VLANsC.only VLANs 1 - 64D.only the VLANs that are specified when creating the trunk
Which commands, when used together, would create an 802.1Q link?()A、Switch(vlan)# mode trunkB、Switch(config)# switchport access mode trunkC、Switch(config-if)# switchport mode trunkD、Switch(config-if)# switchport trunk encapsulation dot1qE、Switch(config)# switchport access mode 1F、Switch(vlan)# trunk encapsulation dot1q
Which three statements about VTP features are true?()A、When properly configured,VTP minimizes VLAN misconfigurations and configuration inconsistenciesB、Each broadcast domain on a switch can have its own unique VTP domainC、VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured.D、When properly configured,VTP maintains VLAN configuration consistency and accelerates trunk link negotiation.E、VTP pruning is used to increase available bandwidth in trunk linksF、Client,server,and transparent are valid VTP modesG、To configure a switch to be part of two VTP domains,each domain must have its own passwords
You are the network administrator tasked with designing a switching solution for the Company network. Which of the following statements describing trunk links are INCORRECT?()A、 The trunk link belongs to a specific VLAN.B、 Multiple trunk links are used to connect multiple end user devices.C、 A trunk link only supports native VLAN.D、 Trunk links use 802.10 to identify a VLAN.E、 The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.
Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol (DTP) desirable mode?()A、 The interface actively attempts to convert the link to a trunk link.B、 The interface is put into permanent trunking mode but prevented from generating DTP frames. C、 The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.D、 The interface is put into a passive mode, waiting to convert the link to a trunk link. E、 None of the other alternatives apply
Two Company switches are connected via a trunk link. In this network, the original frame is encapsulated and an additional header is added before the frame is carried over a trunk link. At the receiving end, the header is removed and the frame is forwarded to the assigned VLAN. This describes which technology?()A、 DISLB、 ISLC、 DTPD、 IEEE 802.1QE、 MPLSF、 None of the other alternatives apply
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?()A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link()。A、By default, all defined VLANs are allowed on the trunk.B、Each single VLAN, or VLAN range, must be specified with the switchport mode command.C、Each single VLAN, or VLAN range, must be specified with the vtp domain command.D、Each single VLAN, or VLAN range, must be specified with the vlan database command.
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?()A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
VLAN Tagging, also known as Frame Tagging, is a method developed by Cisco to help identify packets travelling through trunk links. When an Ethernet frame traverses a trunk link, a special VLAN tag is added to the frame and sent across the trunk link .How does ERS use the VLAN tag?()A、provide service internetworkingB、support transparency for Layer 2 framesC、indicate destination as a connection identifierD、map to the DLCI in service internetworking
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。A、no VLANsB、all VLANsC、only VLANs 1 - 64D、only the VLANs that are specified when creating the trunk
When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?()A、BlockingB、AutoC、DesirableD、OnE、TransparentF、Learning
If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1, which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner (R2) and become a trunk? ()A、 AutoB、 NegotiateC、 DesignateD、 No negotiate
单选题Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol (DTP) desirable mode?()A The interface actively attempts to convert the link to a trunk link.B The interface is put into permanent trunking mode but prevented from generating DTP frames. C The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.D The interface is put into a passive mode, waiting to convert the link to a trunk link. E None of the other alternatives apply
多选题Which commands, when used together, would create an 802.1Q link?()ASwitch(vlan)# mode trunkBSwitch(config)# switchport access mode trunkCSwitch(config-if)# switchport mode trunkDSwitch(config-if)# switchport trunk encapsulation dot1qESwitch(config)# switchport access mode 1FSwitch(vlan)# trunk encapsulation dot1q
多选题You are the network administrator tasked with designing a switching solution for the Company network. Which of the following statements describing trunk links are INCORRECT?()AThe trunk link belongs to a specific VLAN.BMultiple trunk links are used to connect multiple end user devices.CA trunk link only supports native VLAN.DTrunk links use 802.10 to identify a VLAN.EThe native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.
单选题If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1, which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner (R2) and become a trunk? ()A AutoB NegotiateC DesignateD No negotiate
多选题When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?()ABlockingBAutoCDesirableDOnETransparentFLearning
单选题When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link?()Ano VLANsBall VLANsConly VLANs 1 - 64Donly the VLANs that are specified when creating the trunk
判断题通过以下命令 Port link-type trunk Port trunk permit vlan 10 可以将交换机的端口设置为 Trunk 端口,允许 VLAN10 报文通过,其他的拒绝。A对B错