A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?（）A、More collision domains will be created.B、IP address utilization will be more efficient.C、More bandwidth will be required than was needed previously.D、An additional broadcast domain will be created.
A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?（）
- A、More collision domains will be created.
- B、IP address utilization will be more efficient.
- C、More bandwidth will be required than was needed previously.
- D、An additional broadcast domain will be created.
相关考题：
A Ezonexam switch is configured with all ports assigned to VLAN 2. In addition, all ports are configured as full-duplex FastEthernet. What is the effect of adding switch ports to a new VLAN on this switch?A．The additions will create more collisions domains.B．IP address utilization will be more efficient.C．More bandwidth will be required than was needed previously.D．An additional broadcast domain will be created.E．The possibility that switching loops will occur will increase dramatically.
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?A. No VLANsB. Only the VLANs that are specified when creating the trunkC. Only VLANs 1-64D. All VLANsE. All VLAN's except VLAN 1F. None of the above
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur? (Choose all that apply).A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
Which commands is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?() A. transport type allB. transport output allC. transport preferred allD. transport input all
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link()。 A.no VLANsB.all VLANsC.only VLANs 1 - 64D.only the VLANs that are specified when creating the trunk
f a Cisco switch is configured with VTPv1 in transparent mode， what is done with received VTP advertisements？（）A、They are discardedB、The contents are altered to reflect the switch’s own VTP database and then they are forward out all trunking portsC、The changes within the advertisements are made to the switch’s VTP database.D、The contents are ignored and they are forwarded out all trunking ports.
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? （）A、All ports will be in a state of discarding, learning, or forwarding.B、Thirty VLANs have been configured on this switch.C、The bridge priority is lower than the default value for spanning tree.D、All interfaces that are shown are on shared media.E、All designated ports are in a forwarding state.F、The switch must be the root bridge for all VLANs on this switch.
What are the switch and bridge port characteristics of a layer two spanning-tree network that is fully converged?（）A、All switch and bridge ports are in the forwarding state.B、All switch and bridge ports are in the stand-by state.C、All switch and bridge ports are assigned as either root or designated ports.D、All switch and bridge ports are in either the forwarding or blocking state.E、All switch and bridge are either blocking or looping.
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）A、The switch must be configured with an IP address,subnet mask,and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch port.F、The switch must be fully configured as an SNMP agent.
The following was configured on a switch： Switch（config） # spanning-tree portfast bpdufilter default What is the effect of this configuration command？（）A、If BPDUs are received by a port configured for PortFast， they are ignored and none are sent.B、The command will enable BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.C、If BPDUs are received by a port configured for Portfast， the port will transition to forwarding state.D、If BPDUs are received by a port configured for PortFast， then PortFast is disabled and the BPDUs are processed normally.E、None of the other alternatives apply.
Which commands is necessary to permit SSH or Telnet access to a cisco switch that is otherwise configured for these vty line protocols?（）A、transport type allB、transport output allC、transport preferred allD、transport input all
Switch R1 is configured to use the VLAN Trunking Protocol （VTP）. What does R1 advertise in its VTP domain？（）A、The VLAN ID of all known VLANs，the management domain name，and the total number of trunk links on the switch.B、The VLAN ID of all known VLANs，a 1-bit canonical format （CF1 Indicator），and the switch configuration revision number.C、The management domain name，the switch configuration revision number，the known VLANs， and their specific parameters.D、A 2-byte TPID with a fixed value of 0x8100 for the management domain number，the switch configuration revision number，the known VLANs，and their specific parameters.E、None of the other alternatives apply.
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link（）。A、no VLANsB、all VLANsC、only VLANs 1 - 64D、only the VLANs that are specified when creating the trunk
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
Switch A is configured with VLAN 105 and 106. Switch Bis configured with VLAN 105 and 107.Both switches are connected with a fiber cable. In order for packets from all VLANs to cross thefiber cable, which of the following configurations MUST be present? （）A、Reverse ARPB、Full duplex on the fiber linkC、PoED、802.1q trunking
多选题Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? （）AAll ports will be in a state of discarding, learning, or forwarding.BThirty VLANs have been configured on this switch.CThe bridge priority is lower than the default value for spanning tree.DAll interfaces that are shown are on shared media.EAll designated ports are in a forwarding state.FThe switch must be the root bridge for all VLANs on this switch.
单选题Switch A is configured with VLAN 105 and 106. Switch Bis configured with VLAN 105 and 107.Both switches are connected with a fiber cable. In order for packets from all VLANs to cross thefiber cable, which of the following configurations MUST be present? （）AReverse ARPBFull duplex on the fiber linkCPoED802.1q trunking
单选题f a Cisco switch is configured with VTPv1 in transparent mode， what is done with received VTP advertisements？（）AThey are discardedBThe contents are altered to reflect the switch’s own VTP database and then they are forward out all trunking portsCThe changes within the advertisements are made to the switch’s VTP database.DThe contents are ignored and they are forwarded out all trunking ports.
单选题Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）A The access link needs to be configured in multiple VLANs.B The link between the switches is configured in the wrong VLAN.C The link between the switches needs to be configured as a trunk.D VTP is not configured to carry VLAN information between the switches.E Switch IP addresses must be configured in order for traffic to be forwarded between the switches
多选题You have configured voice VLANs on Catalyst switch R1. Which two statements are true about the operation of voice VLANs on this device？ （）AWhen the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port.BEnabling voice VLANs enables the switch to create multiple queues for traffic that is entering a port.CWhen voice VLANs are configured on a trunk link， UplinkFast must also be enabled.DVoice VLANs are configured to enable the switch to forward frames marked with the proper CoS values over separate physical links.EEnabling voice VLANs enables the switch to forward frames with a specific 802.1P marking.
单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）AoneBthreeCtwoDzero
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）AThe switch must be configured with an IP address,subnet mask,and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch port.FThe switch must be fully configured as an SNMP agent.
单选题A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?（）AMore collision domains will be created.BIP address utilization will be more efficient.CMore bandwidth will be required than was needed previously.DAn additional broadcast domain will be created.