Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? ()
A.The Router1 WAN port is configured as a trunking port.
B.The Router1 port connected to Switch1 is configured using subinterfaces.
C.The Router1 port connected to Switch1 is configured as 10 Mbps.
D.The Switch1 port connected to Router1 is configured as a trunking port.
E.The Switch1 port connected to Host B is configured as an access port.
F.The Switch1 port connected to Hub1 is configured as full duplex.
相关考题：
As a network administrator, you are required to configure a switch port for a private Virtual LAN. In such a situation, which three of the following connection modes will be available during the configuration process? （）(Choose three.)A. isolated modeB. modular modeC. community modeD. promiscuous modeE. non-isolatedF. permanent
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）A.The Manchester serial address is 10.1.1.1B.The Manchester serial address is 10.1.1.2C.这个Manchester路由器串口地址为：10.1.12D.The London router is a Cisco 2610.E.The Manchester router is a Cisco 2610.F.The CDP information was received on port Serial0/0 of the Manchester router.G.The CDP information was sent by port Serial0/0 of the London Router.
Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role?() A.Switch3, port fa0/1B.Switch3, port fa0/12C.Switch4, port fa0/11D.Switch4, port fa0/2E.Switch3, port Gi0/1F.Switch3, port Gi0/2
Which statement is true regarding the Port Aggregation Protocol？ （）A、Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.B、Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.C、Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.D、The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology？（）A、lowest port MAC addressB、port priority number and MAC addressC、VTP revision numberD、highest port priority numberE、path cost
Which two of the following statements describe a routed switch port on a multilayer switch？（）A、Layer 2 switching and Layer 3 routing are mutually supported.B、The port will not be associated with any VLAN.C、The routed switch port supports VLAN subinterfaces.D、The routed switch port is used when a switch has only one port per VLAN or subnet.E、The routed switch port ensures that STP remains in the forwarding state.
Refer to the router topology shown in the graphic. Assuming that all routers are running OSPF, which statements correctly describe how the routers exchange routing information?（）A、Denmark exchanges with Utah, Paris, and Berlin.B、Utah exchanges only with Denmark.C、Berlin exchanges with Denmark, Utah, and Paris.D、Paris exchanges only with Denmark.E、Denmark exchanges with only Paris and Utah.
What value is primarily used to determine which port becomes the root port on each non root switch in a spanning-tree topology?（）A、path costB、lowest port MAC addressC、VTP revision numberD、highest port priority numberE、port priority number and MAC address
A network administrator needs to configure port security on a switch.which two statements are true?（）A、The network administrator can apply port security to dynamic access portsB、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.C、The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.D、The network administrator can apply port security to EtherChannels.E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.
What is the function of the no switchport catalyst switch interface configuration command?（）A、Disables the interfaces to prevent traffic flowB、Clears all the configurations on the interfaceC、Switches the port from access mode to trunk modeD、Converts the port from physical Layer 2 port to physical Layer 3 port
Which statements describe two of the benefits of VLAN Trunking Protocol?（）A、VTP allows routing between VLANs.B、VTP allows a single switch port to carry information to more than one VLAN.C、VTP allows physically redundant links while preventing switching loops.D、VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.E、VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.F、VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
As a network administrator, you are required to configure a switch port for a private Virtual LAN. In such a situation, which three of the following connection modes will be available during the configuration process? （）(Choose three.)A、isolated modeB、modular modeC、community modeD、promiscuous modeE、non-isolatedF、permanent
A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv. Interface fastethernet 1/10 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface fastethernet 1/11 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface port-channel 10 Switchport mode trunk Switchport allowed vlan all No shut Which Port Channel configuration must be used on the Nexus 1000v port-profile？（）A、 MAC pinningB、 Cisco Discovery Protocol pinningC、 Mode OnD、 Mode ActiveE、 No port channel configuration
Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）A、The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2B、The configuration is invalid because the DHCP options are global configuration commandsC、The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesD、The router will choose which pool to use based upon the interface the DHCP request wasreceived on
Which statement is correct about RSTP port roles？（）A、The designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.B、The disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.C、The backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.D、The root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
A Company switch was configured as shown below： switchport mode access switchport port-security switchport port-security maximum 2 switchport port-security mac-address 0002.0002.0002 switchport port-security violation shutdown Given the configuration output shown above， what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）A、 The host will be allowed to connect.B、 The port will shut down.C、 The host can only connect through a hub/switch where 0002.0002.0002 is already connected. D、 The host will be refused access.E、 None of the other alternatives apply
单选题When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）AEnable the switch to participate in routing updates from external devices with the router command in global configuration mode.BEnter the no switchport command to disable Layer 2 functionality at the interface level.CEach port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.DRouting is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
单选题Which statement is correct about RSTP port roles？（）AThe designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.BThe disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.CThe backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.DThe root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
单选题A Company switch was configured as shown below： switchport mode access switchport port-security switchport port-security maximum 2 switchport port-security mac-address 0002.0002.0002 switchport port-security violation shutdown Given the configuration output shown above， what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）A The host will be allowed to connect.B The port will shut down.C The host can only connect through a hub/switch where 0002.0002.0002 is already connected. D The host will be refused access.E None of the other alternatives apply
多选题As a network administrator, you are required to configure a switch port for a private Virtual LAN. In such a situation, which three of the following connection modes will be available during the configuration process? （）(Choose three.)Aisolated modeBmodular modeCcommunity modeDpromiscuous modeEnon-isolatedFpermanent
多选题Refer to the router topology shown in the graphic. Assuming that all routers are running OSPF, which statements correctly describe how the routers exchange routing information?（）ADenmark exchanges with Utah, Paris, and Berlin.BUtah exchanges only with Denmark.CBerlin exchanges with Denmark, Utah, and Paris.DParis exchanges only with Denmark.EDenmark exchanges with only Paris and Utah.
单选题What value is primarily used to determine which port becomes the root port on each non root switch in a spanning-tree topology?（）Apath costBlowest port MAC addressCVTP revision numberDhighest port priority numberEport priority number and MAC address
多选题Which statements describe two of the benefits of VLAN Trunking Protocol？（）AVTP allows routing between VLANs.BVTP allows a single switch port to carry information to more than one VLAN.CVTP allows physically redundant links while preventing switching loops.DVTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.EVTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.FVTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
单选题Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）AThe router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2BThe configuration is invalid because the DHCP options are global configuration commandsCThe configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesDThe router will choose which pool to use based upon the interface the DHCP request wasreceived on
多选题Which three statements best describe HSRP configuration on Cisco Nexus switches？（）AIn a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.BIn a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.CYou can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.DYou can use the show standby command to verify HSRP operation and configuration.EIf you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
单选题What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology？（）Alowest port MAC addressBport priority number and MAC addressCVTP revision numberDhighest port priority numberEpath cost
多选题Which two of the following statements describe a routed switch port on a multilayer switch？（）ALayer 2 switching and Layer 3 routing are mutually supported.BThe port will not be associated with any VLAN.CThe routed switch port supports VLAN subinterfaces.DThe routed switch port is used when a switch has only one port per VLAN or subnet.EThe routed switch port ensures that STP remains in the forwarding state.