Refer to Topic TestKing.com in iPAD document.What happens to the network when TestKingX is reconnected and a trunk exists between the two switches?（）A、All VLANs except the default VLAN will be removed from all switches.B、All existing switches will have the students, admin, faculty, Servers, Management,Production, and no-where VLANs.C、The VLANs Servers, Management, Production, and no-where will replace the VLANs on SwX.D、The VLANs Servers, Management, Production, and no-where will be removed from existing switches.
Refer to Topic TestKing.com in iPAD document.What happens to the network when TestKingX is reconnected and a trunk exists between the two switches?（）
- A、All VLANs except the default VLAN will be removed from all switches.
- B、All existing switches will have the students, admin, faculty, Servers, Management,Production, and no-where VLANs.
- C、The VLANs Servers, Management, Production, and no-where will replace the VLANs on SwX.
- D、The VLANs Servers, Management, Production, and no-where will be removed from existing switches.
相关考题：
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?A．All defined VLANs are allowed on the trunk by default.B．Each VLAN, or VLAN range, that is specified with the switchport mode command.C．Each VLAN, or VLAN range, that is specified with the vtp domain command.D．Each VLAN, or VLAN range, that is specified with the vlan database command.E．None of the above
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?A. No VLANsB. Only the VLANs that are specified when creating the trunkC. Only VLANs 1-64D. All VLANsE. All VLAN's except VLAN 1F. None of the above
What must the Ezonexam network administrator do in order to successfully configure a VLAN trunk between two switches named VE1 and VE2? (Select two answer choices)A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).A．You must set each end of the trunk line to IEEE 802.1e encapsulation.B．You must set the same VTP management domain name on both switches.C．You must set all ports on the two switches as access ports.D．You must configure one of the switches as a VTP server.E．You must use a rollover cable to connect the two switches.
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur? (Choose all that apply).A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
When is a switched network that is running the Spanning Tree Protocol considered to be fully converged?A．when all switches have the same BID as the root switchB．when all switches have received the MAC address of each neighboring switchC．when every enabled switch port has been assigned a unique identifierD．when every operating switch port is in either the blocking or forwarding stateE．when all switches are in either client, server, or transparent mode
What are some of the characteristics of a typical VLAN arrangement, found throughout the Ezonexam switched LAN? (Select all that apply)A. VLANs logically divide a switch into multiple, independent switches at Layer 2.B. Trunk links can carry traffic for multiple VLANs.C. VLAN implementation significantly increases traffic due to added trunking information.D. A VLAN can span multiple switches.E. VLANs typically increase the number of switches neededF. VLANs typically decrease the number of switches needed
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? （）(Choose two.)A. Turn off MST (802.1s) on all switches.B. Turn on MST (802.1s) on all switches.C. Turn on RSTP (802.1w) on all switches.D. Turn off RSTP (802.1w) on all switches.
Refer to Topic TestKing.com in iPAD document.What happens to the network when TestKingX is reconnected and a trunk exists between the two switches?() A. All VLANs except the default VLAN will be removed from all switches.B. All existing switches will have the students, admin, faculty, Servers, Management,Production, and no-where VLANs.C. The VLANs Servers, Management, Production, and no-where will replace the VLANs on SwX.D. The VLANs Servers, Management, Production, and no-where will be removed from existing switches.
What must an administrator do in order to successfully configure a VLAN trunk between two switches?() A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?() A. All defined VLANs are allowed on the trunk by default.B. Each VLAN, or VLAN range, that is specified with the switchport mode command.C. Each VLAN, or VLAN range, that is specified with the vtp domain command.D. Each VLAN, or VLAN range, that is specified with the vlan database command.
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches.Which of the following must you do to accomplish this?（）A. You must set each end of the trunk line to IEEE 802.1e encapsulation.B. You must set the same VTP management domain name on both switches.C. You must set all ports on the two switches as access ports.D. You must configure one of the switches as a VTP server.E. You must use a rollover cable to connect the two switches.
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?() A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.B. The VTP management domain name of both switches must be set the same.C. All ports on both the switches must be set as access ports.D. One of the two switches must be configured as a VTP server.E. A rollover cable is required to connect the two switches together.F. A router must be used to forward VTP traffic between VLANs.
Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）A.The access link needs to be configured in multiple VLANs.B.The link between the switches is configured in the wrong VLAN.C.The link between the switches needs to be configured as a trunk.D.VTP is not configured to carry VLAN information between the switches.E.Switch IP addresses must be configured in order for traffic to be forwarded between the switches
Which three statements accurately describe layer 2 Ethernet switches?() A.Microsegmentation decreases the number of collisions on the network.B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.C.Spanning Tree Protocol allows switches to automatically share vlan information.D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.E.Establishing vlans increases the number of broadcast domains.F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
When is a switched network that is running the Spanning Tree Protocol considered to be fully converged?（）A、when all switches have the same BID as the root switchB、when all switches have received the MAC address of each neighboring switchC、when every enabled switch port has been assigned a unique identifierD、when every operating switch port is in either the blocking or forwarding stateE、when all switches are in either client, server, or transparent mode
The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN. Which three statements about the MST protocol （IEEE 802.1S） are true？ （）A、 To verify the MST configuration， the show pending command can be used in MST configuration mode.B、 When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.C、 All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.D、 All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.E、 An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.F、 Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）A、Verify that different native VLANs exist between two switches for security purposes.B、Verify that the VLAN was added on all switches with the use of the show vlan command. C、Verify that the switch is configured to allow for trunking on the switch ports.D、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.
A new switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?（）A、All defined VLANs are allowed on the trunk by default.B、Each VLAN, or VLAN range, that is specified with the switchport mode command.C、Each VLAN, or VLAN range, that is specified with the vtp domain command.D、Each VLAN, or VLAN range, that is specified with the vlan database command.
You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）A、The link is using IEEE 802.1Q protocolB、The link is using IEEE 802.1E protocolC、Spanning tree is disabledD、Not enough information to determineE、The native VLAN information is identical at each end of the linkF、The native VLAN information is different at each end of the link
What must an administrator do in order to successfully configure a VLAN trunk between two switches?（）A、Set each end of the trunk line to IEEE 802.1Q encapsulation.B、Set the same VTP management domain name on both switches.C、Set all ports on the two switched as access ports.D、Configure one of the two switches as a VTP server.E、Connect the two switches using a rollover cable.F、Use a router to forward VTP traffic between the VLANs.
When a new trunk is configured on a 2950 switch, which VLANs by default are allowed over the trunk link（）。A、no VLANsB、all VLANsC、only VLANs 1 - 64D、only the VLANs that are specified when creating the trunk
Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）A、Because the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.B、As a VTP server， the new switch deleted all VLANs of the network.C、Erasing VLANs increases the VTP configuration revision.D、Since the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.
单选题Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）ABecause the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.BAs a VTP server， the new switch deleted all VLANs of the network.CErasing VLANs increases the VTP configuration revision.DSince the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.
单选题When is a switched network that is running the Spanning Tree Protocol considered to be fully converged?（）Awhen all switches have the same BID as the root switchBwhen all switches have received the MAC address of each neighboring switchCwhen every enabled switch port has been assigned a unique identifierDwhen every operating switch port is in either the blocking or forwarding stateEwhen all switches are in either client, server, or transparent mode
单选题Refer to Topic TestKing.com in iPAD document.What happens to the network when TestKingX is reconnected and a trunk exists between the two switches?（）AAll VLANs except the default VLAN will be removed from all switches.BAll existing switches will have the students, admin, faculty, Servers, Management,Production, and no-where VLANs.CThe VLANs Servers, Management, Production, and no-where will replace the VLANs on SwX.DThe VLANs Servers, Management, Production, and no-where will be removed from existing switches.
多选题You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）AThe link is using IEEE 802.1Q protocolBThe link is using IEEE 802.1E protocolCSpanning tree is disabledDNot enough information to determineEThe native VLAN information is identical at each end of the linkFThe native VLAN information is different at each end of the link