What must the Ezonexam network administrator do in order to successfully configure a VLAN trunk between two switches named VE1 and VE2? (Select two answer choices)A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
What must the Ezonexam network administrator do in order to successfully configure a VLAN trunk between two switches named VE1 and VE2? (Select two answer choices)
A. Set each end of the trunk line to IEEE 802.1Q encapsulation.
B. Set the same VTP management domain name on both switches.
C. Set all ports on the two switched as access ports.
D. Configure one of the two switches as a VTP server.
E. Connect the two switches using a rollover cable.
F. Use a router to forward VTP traffic between the VLANs.
相关考题：
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?A．All defined VLANs are allowed on the trunk by default.B．Each VLAN, or VLAN range, that is specified with the switchport mode command.C．Each VLAN, or VLAN range, that is specified with the vtp domain command.D．Each VLAN, or VLAN range, that is specified with the vlan database command.E．None of the above
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).A．You must set each end of the trunk line to IEEE 802.1e encapsulation.B．You must set the same VTP management domain name on both switches.C．You must set all ports on the two switches as access ports.D．You must configure one of the switches as a VTP server.E．You must use a rollover cable to connect the two switches.
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur? (Choose all that apply).A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
The Ezonexam network administrator has issued the "VTP password ezonexam" command on a Cisco device. What is the purpose of this command?A．It allows two VTP servers to exists in the same domain, each configured with different passwordsB．It is the password required when promoting a switch from VTP client mode to VTP server modeC．It is used to access the VTP server to make changes to the VTP configurationD．It is used to validate the sources of VTP advertisements sent between switchesE．None of the above
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A. The switch that will share its VLAN configuration must be in VTP server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be connected over VLAN trunks.E. The switches must be configured to use the same STP version.F. The switches must have VTP pruning activated.
What must an administrator do in order to successfully configure a VLAN trunk between two switches?() A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches.Which of the following must you do to accomplish this?（）A. You must set each end of the trunk line to IEEE 802.1e encapsulation.B. You must set the same VTP management domain name on both switches.C. You must set all ports on the two switches as access ports.D. You must configure one of the switches as a VTP server.E. You must use a rollover cable to connect the two switches.
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?() A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.B. The VTP management domain name of both switches must be set the same.C. All ports on both the switches must be set as access ports.D. One of the two switches must be configured as a VTP server.E. A rollover cable is required to connect the two switches together.F. A router must be used to forward VTP traffic between VLANs.
Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）A.The access link needs to be configured in multiple VLANs.B.The link between the switches is configured in the wrong VLAN.C.The link between the switches needs to be configured as a trunk.D.VTP is not configured to carry VLAN information between the switches.E.Switch IP addresses must be configured in order for traffic to be forwarded between the switches
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met? () A.Each end of the trunk line must be set to IEEE 802.1E encapsulation.B.The VTP management domain name of both switches must be set the same.C.All ports on both the switches must be set as access ports.D.One of the two switches must be configured as a VTP server.E.A rollover cable is required to connect the two switches together.F.A router must be used to forward VTP traffic between VLANs.
he network administrator is trying to add Switch1 to the network， but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem？（）A、The trunking configuration mode on Switch1 is set to Off.B、The trunking configuration mode on the other end is set to On.C、The trunking configuration mode on the other end is set to Desirable.D、Cisco Discovery Protocol is not running on the other end.E、There is a VTP domain name mismatch.F、Switch1 does not support 802.1Q
You need to investigate a VTP problem between two Company switches. The lack of which two prevents VTP information from propagating between switches？（）A、A root VTP serverB、A trunk portC、VTP priorityD、VLAN 1E、None of the other alternatives apply
You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）A、The link is using IEEE 802.1Q protocolB、The link is using IEEE 802.1E protocolC、Spanning tree is disabledD、Not enough information to determineE、The native VLAN information is identical at each end of the linkF、The native VLAN information is different at each end of the link
What must an administrator do in order to successfully configure a VLAN trunk between two switches?（）A、Set each end of the trunk line to IEEE 802.1Q encapsulation.B、Set the same VTP management domain name on both switches.C、Set all ports on the two switched as access ports.D、Configure one of the two switches as a VTP server.E、Connect the two switches using a rollover cable.F、Use a router to forward VTP traffic between the VLANs.
You are troubleshooting a Catalyst 5000 trunk in the network. What should you do if there’s adisagreement about the VLANs configured to use the trunk？（）A、Reload the active VLAN configurationB、Clear the affected port and bring it up againC、Explicitly set the trunk for the VLAN to be onD、Remove all the VLANs set
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.
An 802.1Q trunk is not coming up between two switches. The ports on both switches are configured as "switchport mode desirable." Assuming that there is no physical issue， choose two possible causes.（）A、Incorrect VTP domainB、Incorrect VTP passwordC、Incorrect VTP modeD、Incorrect VTP configuration revision
The network administrator is trying to add Switch1 to the network， but the 802.1Q trunk is not coming up. Switch1 was previously tested in the laboratory and its trunk configuration worked fine. What are three possible causes of this problem？ （）A、The trunking configuration mode on Switch1 is set to Off.B、The trunking configuration mode on the other end is set to On.C、The trunking configuration mode on the other end is set to Desirable.D、Cisco Discovery Protocol is not running on the other end.E、There is a VTP domain name mismatch.F、Switch1 does not support 802.1Q.
A switch port on TK1 is being configured to support 802.1Q trunking. Which of the following are true about 802.1Q trunking？（）A、Both switches must be in the same VTP domain.B、The encapsulation type of both ends of the trunk does not have to match.C、The native VLAN on both ends of the trunk must be VLAN 1.D、802.1Q trunking can only be configured on a Layer 2 port.E、In 802.1Q trunking， all VLAN packets are tagged on the trunk link， except the native VLAN.
If you were to configure an ISL Ethernet trunk between two Cisco switches， named R1 and R2， what would you have to include at the end of the link for the trunk to operate correctly？ （）A、 An identical VTP mode.B、 An identical speed/duplex.C、 An identical trunk negotiation parameter.D、 An identical trunk encapsulation parameter.
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?（）A、You must set each end of the trunk line to IEEE 802.1e encapsulation.B、You must set the same VTP management domain name on both switches.C、You must set all ports on the two switches as access ports.D、You must configure one of the switches as a VTP server.E、You must use a rollover cable to connect the two switches.
多选题What must an administrator do in order to successfully configure a VLAN trunk between two switches?（）ASet each end of the trunk line to IEEE 802.1Q encapsulation.BSet the same VTP management domain name on both switches.CSet all ports on the two switched as access ports.DConfigure one of the two switches as a VTP server.EConnect the two switches using a rollover cable.FUse a router to forward VTP traffic between the VLANs.
多选题To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?（）AEach end of the trunk line must be set to IEEE 802.1E encapsulation.BThe VTP management domain name of both switches must be set the same.CAll ports on both the switches must be set as access port.DOne of the two switches must be configured as a VTP server.EA rollover cable is required to connect the two switches together.FA router must be used to forward VTP traffic between VLANs.
多选题If you were to configure an ISL Ethernet trunk between two Cisco switches， named R1 and R2， what would you have to include at the end of the link for the trunk to operate correctly？ （）AAn identical VTP mode.BAn identical speed/duplex.CAn identical trunk negotiation parameter.DAn identical trunk encapsulation parameter.
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.
多选题You have a trunk link operating between two switches and you’re experiencing problems withframes leaking between the two VLANs. Each switch has identical modules， software revisionsand VLAN configuration information. Spanning tree protocol is disabled on all VLANs. What isprobably causing this problem？（）AThe link is using IEEE 802.1Q protocolBThe link is using IEEE 802.1E protocolCSpanning tree is disabledDNot enough information to determineEThe native VLAN information is identical at each end of the linkFThe native VLAN information is different at each end of the link