What does a configuration Register Setting of 0x2105 indicate to the Router? () A. The Boot IOS Code is Located in the NVRAM.B. Check NVRAM for boot system Commands.C. Bypass NVRAM Configurations.D. Boot the IOS Code Located in ROM.E. Perform a Password Recovery.F. Bypass The Code In ROM.
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
A. The Boot IOS Code is Located in the NVRAM.
B. Check NVRAM for boot system Commands.
C. Bypass NVRAM Configurations.
D. Boot the IOS Code Located in ROM.
E. Perform a Password Recovery.
F. Bypass The Code In ROM.
相关考题：
What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was issued from the privileged mode prompt.E. The IOS is missing.F. The IOS is corrupt.
What is the default configuration register setting on most Cisco routers?A. 0x2104B. 0x2012C. 0x2210D. 0x2102E. 0x2142F. None of the above
An authentication request for a PPP over ATM client has been returned to the router with an address of 255.255.255.254.What does this indicate to the router?() A. A static IP address is used.B. An unnumbered address is used.C. The returned RADIUS address is used.D. The IP address-pool configuration is used.
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? () A.0x2100B.0x2101C.0x2102D.0x2124E.0x2142
After making changes to the router, you issue the copy running-config startup-config command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）A. The NVRAM is corrupted.B. The boot system commands were omitted in the configuration.C. The configuration register setting is incorrect.D. The upgraded configuration incompatible with the hardware platform.E. The upgraded IOS incompatible with the hardware.
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?() A. The IOS image will be ignored.B. The router will prompt to enter initial configuration mode.C. The router will boot to ROM.D. Any configuration entries in NVRAM will be ignored.E. The configuration in flash memory will be booted.
What does a configuration Register Setting of 0x2105 indicate to the Router? （）A、The Boot IOS Code is Located in the NVRAM.B、Check NVRAM for boot system Commands.C、Bypass NVRAM Configurations.D、Boot the IOS Code Located in ROM.E、Perform a Password Recovery.F、Bypass The Code In ROM.
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）A、The IOS image will be ignored.B、The router will prompt to enter initial configuration mode.C、The router will boot to ROM.D、Any configuration entries in NVRAM will be ignored.E、The configuration in flash memory will be booted.
A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?（）A、It checks the configuration register.B、It attempts to boot from a TFTP server.C、It loads the first image file in flash memory.D、It inspects the configuration file in NVRAM for boot instructions.
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）A、The NVRAM is corrupted.B、The boot system commands were omitted in the configuration.C、The configuration register setting is incorrect.D、The upgraded configuration incompatible with the hardware platform.E、The upgraded IOS incompatible with the hardware.
What information does the help topic command provide?（）A、router’s version and serial number to help open a case with JTACB、software documentation describing features and configuration tasks within JUNOSC、a brief description of commands and their default valuesD、a verification of the current configuration on the router
In PIM-SM operations，to which device does the first router that connects with the multicast source sendthe register message？（）A、RPB、multicast sourceC、IGMP routerD、multicast receiverE、PIM designated router
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next？（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file. Which command will display this information, and what is the configuration register value that should be displayed?（）A、show startup-config and 0x2142B、show version and 0x2102C、show flash and 0x2102D、show version and 0x2142E、show running-config and 0x2142F、show flash and 0x2142
An authentication request for a PPP over ATM client has been returned to the router with an address of 255.255.255.254. What does this indicate to the router?（）A、A static IP address is used.B、An unnumbered address is used.C、The returned RADIUS address is used.D、The IP address-pool configuration is used.
单选题An authentication request for a PPP over ATM client has been returned to the router with an address of 255.255.255.254. What does this indicate to the router?（）AA static IP address is used.BAn unnumbered address is used.CThe returned RADIUS address is used.DThe IP address-pool configuration is used.
单选题A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?（）AIt checks the configuration register.BIt attempts to boot from a TFTP server.CIt loads the first image file in flash memory.DIt inspects the configuration file in NVRAM for boot instructions.
单选题An administrator needs to update a router configuration for a router that does not support SSH.Which of the following can be used to securely update the router configuration?（）AFTPBSNMPv2CTFTPDKTTPS
单选题What information does the help topic command provide?（）Arouter’s version and serial number to help open a case with JTACBsoftware documentation describing features and configuration tasks within JUNOSCa brief description of commands and their default valuesDa verification of the current configuration on the router
单选题What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）A0x2100B0x2101C0x2102D0x2124E0x2142
单选题A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next?（）AIt checks the configuration registerBIt attempts to boot from a TFTP serverCIt loads the first image file in flash memoryDIt inspects the configuration file in NVRAM for boot instructions
单选题A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）AIt checks the configuration registerBIt attempts to boot from a TFTP serverCIt loads the first image file in flash memoryDIt inspects the configuration file in NVRAM for boot instructions
单选题In PIM-SM operations，to which device does the first router that connects with the multicast source sendthe register message？（）ARPBmulticast sourceCIGMP routerDmulticast receiverEPIM designated router
多选题A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）AThe IOS image will be ignored.BThe router will prompt to enter initial configuration mode.CThe router will boot to ROM.DAny configuration entries in NVRAM will be ignored.EThe configuration in flash memory will be booted.
单选题What does a configuration Register Setting of 0x2105 indicate to the Router? （）AThe Boot IOS Code is Located in the NVRAM.BCheck NVRAM for boot system Commands.CBypass NVRAM Configurations.DBoot the IOS Code Located in ROM.EPerform a Password Recovery.FBypass The Code In ROM.
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A The network administrator faled to save the configuration.B The configuration register is set to 0x2100.C The boot system flash command is missing from the configuration.D The configuraiton register is set to 0x2102.E The router is configured with the boot system startup command.