What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was issued from the privileged mode prompt.E. The IOS is missing.F. The IOS is corrupt.
What will cause a Ezonexam router to enter setup mode? (Choose two)
A. The configuration file is missing in NVRAM.
B. The configuration register is set to 0x2100.
C. Boot system commands are misconfigured in the running-configuration.
D. The setup command was issued from the privileged mode prompt.
E. The IOS is missing.
F. The IOS is corrupt.
相关考题：
What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?A．It will search for the configuration file in the locations specified by boot system commands.B．It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D．It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
You are a senior network administrator at Ezonexam, and while performing the password recovery procedure on your 2500 series Cisco router, you type in the following command:o/r 0x2142What is the purpose of this command?A．It is used to restart the router.B．It is used to bypass the configuration in NVRAM.C．It is used to enter ROM Monitor mode.D．It is used to view the lost password.E．It is used to save the changes to the configuration.
Why might the Ezonexam network administrator set the configuration register to 0x2142 on a 2600 series Cisco router?A．To boot the IOS from ROMB．To reset the console passwordC．To upload a new version of the configuration fileD．To upload a new version of the IOSE．To allow a new memory upgrade to be recognized by the router
What does a configuration Register Setting of 0x2105 indicate to the Router? () A. The Boot IOS Code is Located in the NVRAM.B. Check NVRAM for boot system Commands.C. Bypass NVRAM Configurations.D. Boot the IOS Code Located in ROM.E. Perform a Password Recovery.F. Bypass The Code In ROM.
What is the purpose of pressing the Ctrl＋Break keys during the router password recover procedure?() A. To restart the router.B. To bypass the configuration in Flash.C. To view the password before changes are made.D. To bypass setup configuration mode.E. To access ROM Monitor mode.
What will a router do during startup if a configuration file is not located in NVRAM?() A. it will search for the configuration file in the locations specified by boot system commands.B. it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D. it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.Which command will display this information, and what is the configuration register value that should be displayed?（）A. show startup-config and 0x2142B. show version and 0x2102C. show flash and 0x2102D. show version and 0x2142E. show running-config and 0x2142F. show flash and 0x2142
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:Would you like to enter the initial configuration dialog? [yes/no]Why has this occurred?（）A. There is an error in the router DRAM.B. Te IOS image is corrupt.C. The configuration register is set to 0x2142.D. The TFTP server that contains the router configuration file is unreachable.E. A boot system configuration command has placed the router into setup mode.
Exhibit: The following are true with one of the TestKing routers:1) The IOS image in flash is missing2) No Network connectivity is available.3) The router fallback IOS image is corrupt.How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）A. The router will enter setup mode.B. The router will enter ROM monitor mode.C. The router will enter global configuration mode.D. The boot will hang until an IOS is available.
After making changes to the router, you issue the copy running-config startup-config command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）A. The NVRAM is corrupted.B. The boot system commands were omitted in the configuration.C. The configuration register setting is incorrect.D. The upgraded configuration incompatible with the hardware platform.E. The upgraded IOS incompatible with the hardware.
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?() A. The IOS image will be ignored.B. The router will prompt to enter initial configuration mode.C. The router will boot to ROM.D. Any configuration entries in NVRAM will be ignored.E. The configuration in flash memory will be booted.
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next()。 A.Because of damaged flash memory, the router will fail the POST.B.It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.C.It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.D.It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.E.It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）A、Because of damaged flash memory， the router will fail the POSTB、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROMD、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）A、There is an error in the router DRAM.B、Te IOS image is corrupt.C、The configuration register is set to 0x2142.D、The TFTP server that contains the router configuration file is unreachable.E、A boot system configuration command has placed the router into setup mode.
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）A、To restart the router.B、To bypass the configuration in Flash.C、To view the password before changes are made.D、To bypass setup configuration mode.E、To access ROM Monitor mode.
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）A、The IOS image will be ignored.B、The router will prompt to enter initial configuration mode.C、The router will boot to ROM.D、Any configuration entries in NVRAM will be ignored.E、The configuration in flash memory will be booted.
Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）A、The router will enter setup mode.B、The router will enter ROM monitor mode.C、The router will enter global configuration mode.D、The boot will hang until an IOS is available.
You have just purchased a brand new router and wish to have the router prompt you through the initial configuration commands. Which router mode does this describe?（）A、ROM Monitor modeB、SETUP modeC、Autoflash modeD、RXBOOT modeE、None of the above
What will a router do during startup if a configuration file is not located in NVRAM?（）A、it will search for the configuration file in the locations specified by boot system commands.B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）A、The NVRAM is corrupted.B、The boot system commands were omitted in the configuration.C、The configuration register setting is incorrect.D、The upgraded configuration incompatible with the hardware platform.E、The upgraded IOS incompatible with the hardware.
A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file. Which command will display this information, and what is the configuration register value that should be displayed?（）A、show startup-config and 0x2142B、show version and 0x2102C、show flash and 0x2102D、show version and 0x2142E、show running-config and 0x2142F、show flash and 0x2142
单选题After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）AThe NVRAM is corrupted.BThe boot system commands were omitted in the configuration.CThe configuration register setting is incorrect.DThe upgraded configuration incompatible with the hardware platform.EThe upgraded IOS incompatible with the hardware.
多选题A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）AThe IOS image will be ignored.BThe router will prompt to enter initial configuration mode.CThe router will boot to ROM.DAny configuration entries in NVRAM will be ignored.EThe configuration in flash memory will be booted.
单选题What will a router do during startup if a configuration file is not located in NVRAM?（）Ait will search for the configuration file in the locations specified by boot system commands.Bit will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.Cit will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.Dit will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.Eit will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A The network administrator faled to save the configuration.B The configuration register is set to 0x2100.C The boot system flash command is missing from the configuration.D The configuraiton register is set to 0x2102.E The router is configured with the boot system startup command.
单选题During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。ABecause of damaged flash memory, the router will fail the POST.BIt will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.CIt will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.DIt will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.EIt will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
单选题Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）AThe router will enter setup mode.BThe router will enter ROM monitor mode.CThe router will enter global configuration mode.DThe boot will hang until an IOS is available.