Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）A. An access list on router B is causing the 192.168.3.16/28 network to be deniedB. An access list on router B is causing the 192.168.3.32/28 network to be deniedC. The distribute list on router B is referencing a numbered access list that does not exist on router BD. The d istribute list on router B is referencing the wrong interface
Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）
A. An access list on router B is causing the 192.168.3.16/28 network to be denied
B. An access list on router B is causing the 192.168.3.32/28 network to be denied
C. The distribute list on router B is referencing a numbered access list that does not exist on router B
D. The d istribute list on router B is referencing the wrong interface
相关考题：
某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255
下面哪条命令是正确的，如果要将192.168.1.0/24的业务网段发到OSPF的area0（)A.Router(config-router)network 192.168.1.0 0.0.0.2550B.Router(config-router)network 192.168.1.0 0.0.0.255 area0C.Router(config-router)network 192.168.1.0 255.255.255.255 area0D.Router(config-router)network 192.168.1.0 0.0.0.0 area0
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCP clients connected to the FastEthernet0/1 interface are not receiving addresses.Which two statements contain recommendations that will solve the problem?（）A.The network shown in the output under the ip dhcp pool Central command should be changed to network 10.10.0.0 with a mask of 255.255.255.0B.A second DHCP pool for network 10 .10.0.0/24 should be configuredC.An ip dhcp excluded - address global configuration command for network 10.10.0.0/24 should be issuedD.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/0 c onfigurationE.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/1 configuration
RouterAdebug ip ospf events OSPF events debugging is on RouterA 04:43:16: OSPF: Rcv pkt from 10.3.0.2, Ethernet0/1, area 0.0.0.1 mismatch area 0.0.0.2 in the header 04:43:19: OSPF: Rcv hello from 10.100.100.3 area 0 from Ethernet0/0 10.1.0.1 04:43:19: OSPF: End of hello processing Refer to the exhibits. What can be done to fix the problem?（）A. Change router B E0/1 interface to area 0.B. Change router A interface E0/1 to area 0.0.0.2.C. Configure the E0/1 i nterfaces of router A and router B to be in area 0.D. Shut down the E0/1 interfaces in router A and router B as OSPF does not allow back doors between areas.E. Remove the E0/1 interfaces in router A and router B from the OSPF process. Use static rou tes to route data directly from router A to router B to avoid passing data through router C in area 0.
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
Refer to the exhibit. R1 accesses the Internet using E0/0. You have been asked to co nfigure R1 so that a default route is generated to its downstream devices (191.0.0.1 and 192.0.0.1). Which commands would create this configuration? （）A.router eigrp 190redistribute static ! ip route 0.0.0.0 0.0.0.0 Null0B.ip default - network 2 0.0.0.0C.router eigrp 190 redistribute static ! ip route 0.0.0.0 255.255.255.255 Null0D.ip default - network 20.20.20.0
Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the con figuration shown? () A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?() A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1B. R4(config)# ip default - network 10.0.0.0C. R4(config - router)# default -information originateD. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?() A.Router(config)#router ospf 1B.Router(config)#router ospf 0C.Router(config)#router ospf area 0D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E.Router(config-router)#network 192.168.16.0 0.0.0.255 0F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）A.FastEthernet0 /0B.FastEthernet0 /1C.Serial0/0D.Serial0/1.102E.Serial0/1.103F.Serial0/1.104
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）A.The Manchester serial address is 10.1.1.1B.The Manchester serial address is 10.1.1.2C.这个Manchester路由器串口地址为：10.1.12D.The London router is a Cisco 2610.E.The Manchester router is a Cisco 2610.F.The CDP information was received on port Serial0/0 of the Manchester router.G.The CDP information was sent by port Serial0/0 of the London Router.
Refer to the graphic.Host A is communicating with the seiver. What will be the source MAC address of the frames received by Host A from the server?() A.the MAC address of the seiver network interfaceB.the MAC address of host AC.the MAC address of router interface e 1D.the MAC address of router interface e0
WhichcommandsarerequiredtoproperlyconfigurearoutertoproperlyconfigurearoutertorunOSPFandtoaddnetwork192.168.16.0／24toOSPFarea0?() A.Router（config）#routerospf1B.Router（config）#routerospf0C.Router（config）#routerospfarea0D.Router（config-router）#network192.168.16.00.0.0.255area0E.Router（config-router）#network192.168.16.00.0.0.2550F.Router（config-router）#network192.168.16.0255.255.255.0area0
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、TestKingRouter(config)# router ospf 0B、TestKingRouter(config)# router ospf 1C、TestKingRouter(config)# router ospf area 0D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
Router R1 needs to be configured to advertise a specific network. Which of the followingcommands would you use if you wanted to advertise the subnet 154.2.1.0 255.255.255.0 to the EBGP neighbors on your subnet？（）A、Router （config-router）#network 154.2.1.0B、outer （config-router）#network 164.2.1.0C、Router （config-router）#network-advertise 154.2.1.0D、Router （config-router）#network 154.2.1.0 mask 255.255.255.0E、None of the other alternatives apply
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which command can be used to filter a RIPv6 route from getting installed in the routing table？（）A、ipv6 router rip ccie distribute-list..B、ipv6 router rip ccie offset-list..C、interface e0/0 ipv6 rip ccie distribute-list..D、interface e0/0 ipv6 rip ccie advertise..
Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）A、Router(config-router)# network 192.168.10.0 0.0.0.255 0B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D、Router(config)# router ospf 0E、Router(config)# router ospf 1
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
什么命令序列将配置一个路由器运行OSPF，并添加网络10.1.1.0/24 area0？（）A、router ospf area 0 network 10.1.1.0 255.255.255.0 area 0B、router ospf network 10.1.1.0 0.0.0.255C、router ospf 1 network 10.1.1.0 0.0.0.255 area 0D、router ospf area 0 network 10.1.1.0 0.0.0.255 area 0E、router ospf network 10.1.1.0 255.255.255.0 area 0F、router ospf 1 network 10.1.1.0 0.0.0.255
多选题Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）ARouter(config-router)# network 192.168.10.0 0.0.0.255 0BRouter(config-router)# network 192.168.10.0 0.0.0.255 area 0CRouter(config-router)# network 192.168.10.0 255.255.255.0 area 0DRouter(config)# router ospf 0ERouter(config)# router ospf 1
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ATestKingRouter(config)# router ospf 0BTestKingRouter(config)# router ospf 1CTestKingRouter(config)# router ospf area 0DTestKingRouter(config)# network 192.168.16.0 0.0.0.255 0ETestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0FTestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
单选题Router R1 needs to be configured to advertise a specific network. Which of the followingcommands would you use if you wanted to advertise the subnet 154.2.1.0 255.255.255.0 to the EBGP neighbors on your subnet？（）ARouter （config-router）#network 154.2.1.0Bouter （config-router）#network 164.2.1.0CRouter （config-router）#network-advertise 154.2.1.0DRouter （config-router）#network 154.2.1.0 mask 255.255.255.0ENone of the other alternatives apply
多选题Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
单选题Which command can be used to filter a RIPv6 route from getting installed in the routing table？（）Aipv6 router rip ccie distribute-list..Bipv6 router rip ccie offset-list..Cinterface e0/0 ipv6 rip ccie distribute-list..Dinterface e0/0 ipv6 rip ccie advertise..
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ARouter(config)#router ospf 1BRouter(config)#router ospf 0CRouter(config)#router ospf area 0DRouter(config-router)#network 192.168.16.0 0.0.0.255 area 0ERouter(config-router)#network 192.168.16.0 0.0.0.255 0FRouter(config-router)#network 192.168.16.0 255.255.255.0 area 0
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A The network administrator faled to save the configuration.B The configuration register is set to 0x2100.C The boot system flash command is missing from the configuration.D The configuraiton register is set to 0x2102.E The router is configured with the boot system startup command.