Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、TestKingRouter(config)# router ospf 0B、TestKingRouter(config)# router ospf 1C、TestKingRouter(config)# router ospf area 0D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
- A、TestKingRouter(config)# router ospf 0
- B、TestKingRouter(config)# router ospf 1
- C、TestKingRouter(config)# router ospf area 0
- D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
- E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
- F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
相关考题：
某园区网采用 OSPF路由协议,参与 OSPF的网络地址是 169.111.0.0/16, Cisco路由器的正确配置是 （ ） 。A) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 0.0.0.0 area 0Rounter(config_router)# area o range 169.111.0.0 255.255.0.0B) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 255.255.0.0 area 0Rounter(config-router)# area o range 169.111.0.0 255.255.0.0C) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 0.0.255.255 area 0Rounter(config_router)# area o range 169.1-11.0.0 255.255.0.0D) Rounter(config)# router ospf63Rounter(config_router)# network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)# area o range 169.111.0.0 0.0.255.255
某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255
下面哪条命令是正确的，如果要将192.168.1.0/24的业务网段发到OSPF的area0（)A.Router(config-router)network 192.168.1.0 0.0.0.2550B.Router(config-router)network 192.168.1.0 0.0.0.255 area0C.Router(config-router)network 192.168.1.0 255.255.255.255 area0D.Router(config-router)network 192.168.1.0 0.0.0.0 area0
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:*Mar 1 00:2 5:01.084: %OSPF -4- ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0 .How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?（）A.R1(config - router)# area 0 virtual - link 1.1.1.1R3(config - router)# area 2 virtual - link 3.3.3.3B.R1(config - router)# area 1 virtual - link 2.2.2.2 R3(config - router)# area 1 virtual - link 2.2.2.2C.R1(config - router)# area 1 virtual - link 20.20 .20.2 R3(config - router)# area 1 virtual - link 30.30.30.2D.R1(config - router)# area 1 virtual - link 30.30.30.3 R3(config - router)# area 1 virtual - link 20.20.20.1E.R1(config - router)# area 1 virtual - link 3.3.3.3 R3(config - router)# area 1 virtual - link 1.1 .1.1
You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way:Router(config) router ospf 99Router(config-if) network 10.0.0.0 255.0.0.0 area 0Based on this information, what is the most likely problem?（）A. The process id is configured improperly.B. The OSPF area is configured improperly.C. The network wildcard mask is configured improperly.D. The network number is configured improperly.E. The AS is configured improperly.F. The network subnet mask is configured improperly.G. All of the above are likely problems.
Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?() A. On the ABR router ospf 10 area 3 stubB. On all Area 3 routers router ospf 10 area 3 stubC. On all Area 3 routers router ospf 10 area 3 stub no - summaryD. On the ABR router ospf 10 area 3 nssaE. On the ABR rou ter ospf 10 area 3 stub no - summary
Which of the following OSPF commands, when used together, will put the network 192.168.10.0／24 into OSPF area 0?() A. Router(config-router)# network 192.168.10.0 0.0.0.255 0B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D. Router(config)# router ospf 0E. Router(config)# router ospf 1
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)router ospf 1Router(config-router)network 10.0.0.0 255.0.0.0 area 0A. The process id is configured improperlyB. The OSPF area is configured improperlyC. The network wildcard mask is configured improperlyD. The network number is configured improperlyE. The AS is configured improperlyF. The network subnet mask is configuerd improperly
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?() A. Router(config)#router ospf 1B. Router(config)#router ospf 0C. Router(config)#router ospf area 0D. Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E. Router(config-router)#network 192.168.16.0 0.0.0.255 0F. Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?() A.Router(config)#router ospf 1B.Router(config)#router ospf 0C.Router(config)#router ospf area 0D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E.Router(config-router)#network 192.168.16.0 0.0.0.255 0F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A、The AS is not correctly configuredB、The network subnet mask is incorrectly configuredC、The network wildcard mask is configured incorrectlyD、The network number is not correctly configuredE、The process id is configured incorrectlyF、None of the above
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）A、Router（config）#router ospf 1B、Router（config）#router ospf 0C、Router（config）#router ospf area 0D、Router（config-router）#network 192.168.16.0 0.0.0.255 area 0E、Router（config-router）#network 192.168.16.0 0.0.0.255 0F、Router（config-router）#network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）A、Router(config-router)# network 192.168.10.0 0.0.0.255 0B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D、Router(config)# router ospf 0E、Router(config)# router ospf 1
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）A、CEF was not properly configured.B、OSPF was not properly configured for graceful restart.C、Stateful switchover was not correctly configured.D、NSF for OSPF is only supported in area 0.
什么命令序列将配置一个路由器运行OSPF，并添加网络10.1.1.0/24 area0？（）A、router ospf area 0 network 10.1.1.0 255.255.255.0 area 0B、router ospf network 10.1.1.0 0.0.0.255C、router ospf 1 network 10.1.1.0 0.0.0.255 area 0D、router ospf area 0 network 10.1.1.0 0.0.0.255 area 0E、router ospf network 10.1.1.0 255.255.255.0 area 0F、router ospf 1 network 10.1.1.0 0.0.0.255
多选题Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）ARouter(config-router)# network 192.168.10.0 0.0.0.255 0BRouter(config-router)# network 192.168.10.0 0.0.0.255 area 0CRouter(config-router)# network 192.168.10.0 255.255.255.0 area 0DRouter(config)# router ospf 0ERouter(config)# router ospf 1
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ARouter(config)#router ospf 1BRouter(config)#router ospf 0CRouter(config)#router ospf area 0DRouter(config-router)#network 192.168.16.0 0.0.0.255 area 0ERouter(config-router)#network 192.168.16.0 0.0.0.255 0FRouter(config-router)#network 192.168.16.0 255.255.255.0 area 0
单选题某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16，Cisco路由器的正确配置是（ ）。ARounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.0.0 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0BRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 255.255.0.0 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0CRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0DRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)#area 0 range 169.111.0.0 0.0.255.255
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ATestKingRouter(config)# router ospf 0BTestKingRouter(config)# router ospf 1CTestKingRouter(config)# router ospf area 0DTestKingRouter(config)# network 192.168.16.0 0.0.0.255 0ETestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0FTestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
多选题Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
多选题Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
单选题Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）ACEF was not properly configured.BOSPF was not properly configured for graceful restart.CStateful switchover was not correctly configured.DNSF for OSPF is only supported in area 0.
单选题A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）AThe AS is not correctly configuredBThe network subnet mask is incorrectly configuredCThe network wildcard mask is configured incorrectlyDThe network number is not correctly configuredEThe process id is configured incorrectlyFNone of the above