Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）A.FastEthernet0 /0B.FastEthernet0 /1C.Serial0/0D.Serial0/1.102E.Serial0/1.103F.Serial0/1.104
Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）
A.FastEthernet0 /0
B.FastEthernet0 /1
C.Serial0/0
D.Serial0/1.102
E.Serial0/1.103
F.Serial0/1.104
相关考题：
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）A. type 1 Router LSAB. type 2 Network LSAC. type 3 Network Summary LSAD. type 4 ASBR Summary LSAE. type 5 AS External LSAF. type 7 NSSA External LSA
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. Which two Cisco IOS commands on R2 would verify its OSPF neighbor relationships?() A.show ip ospfB.show ip ospf interfaceC.show ip ospf neighborD.show ip ospf databaseE.show ip ospf statisticsF.show running - config begin router ospf
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? () A.The NProuter has two OSPF neighbors in the Full adjacency stateB.The NProuter serial0/0 interface has the OSPF dead timer set to 10 secondsC.The NProuter serial0/0 interface has been configured with an OSPF network type of pointtopointD.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers settingE.The Mismatched error is caus ed by the expiration of the OSPF timers
Refer to the exhibit. ROUTE.com has just implemented this EIGRP network. A network administrator came to you for advice while trying to implement load balancing across part of their EIGRP network. If the variance value is configured as 2 on all routers and all o ther metric and K values are configured to their default values, traffic from the Internet to the data center will be load balanced across how many paths? （）A. 1B. 2C. 3D. 4E. 5
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）A. The redistribution command should be reentered with the match route - type parameter included.B. The redistribution command should be reentered wit h the route - map map - tag parameter included.C. The redistribution command should be reentered with the metric metric - value parameter included.D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
An etwork administrator has enabled OSPF across an NBMA network and has issued the command ip ospf network nonbroadcast. Given those facts, which two statements are true?() A. Interfaces will automatically detect and build adjacencies with neighbor routersB. DR and BDR elections will not occurC. DR and BDR elections will occurD. The neighbor command is required to build adjacenciesE. All routers must be configured in a fully meshed topology with all other routers
Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1?() A. Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAsB. No redistributed routes can appear in Area 1, only summary routesC. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAsD. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）A. The ip ospf network broadcast command should be configured on each Frame Relay interfaceB. The ip ospf network non -broadcast command should be configured on each Frame Relay interfaceC. Th e ip ospf priority value on the spoke routers should be set to 0D. The ip ospf priority value on the hub router should be set to 0E. The neighbor command should be configured under the OSPF routing process on all routers
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?() A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1B. R4(config)# ip default - network 10.0.0.0C. R4(config - router)# default -information originateD. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
Refer to the exhibit. What command sequence will enable PAT from the inside to outside network?() A.(config) ip nat pool isp-net 1.2.4.2 netmask 255.255.255.0 overloadB.(config-if) ip nat outside overloadC.(config) ip nat inside source list 1 interface ethernet1 overloadD.(config-if) ip nat inside overload
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A、As numbers must be changed to match on all the routers.B、Loopback interface must be configured so a DR is elected.C、The no auto-summary command is needed on Router A and Router C.D、Router B needs to have two network statements, one for each connected network.
An etwork administrator has enabled OSPF across an NBMA network and has issued the command ip ospf network nonbroadcast. Given those facts, which two statements are true?（）A、Interfaces will automatically detect and build adjacencies with neighbor routersB、DR and BDR elections will not occurC、DR and BDR elections will occurD、The neighbor command is required to build adjacenciesE、All routers must be configured in a fully meshed topology with all other routers
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）A、CEF was not properly configured.B、OSPF was not properly configured for graceful restart.C、Stateful switchover was not correctly configured.D、NSF for OSPF is only supported in area 0.
单选题Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）A 10.1.1.2B 10.154.154.1C 172.16.5.1D 192.168.5.3
单选题Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors？（）A R4（config）# ip default-network 10.0.0.0B R4（config）# ip route 0.0.0.0 0.0.0.0 10.1.1.1C R4（config）# ip route 10.0.0.0 255.0.0.0 10.1.1.1D R4（config-router）# default-information originate
单选题Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）ACEF was not properly configured.BOSPF was not properly configured for graceful restart.CStateful switchover was not correctly configured.DNSF for OSPF is only supported in area 0.
单选题A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0AThe process id is configured improperlyBThe OSPF area is configured improperlyCThe network wildcard mask is configured improperlyDThe network number is configured improperlyEThe AS is configured improperlyFThe network subnet mask is configuerd improperly
单选题You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way: Router(config)# router ospf 99 Router(config-if)# network 10.0.0.0 255.0.0.0 area 0 Based on this information, what is the most likely problem?（）AThe process id is configured improperly.BThe OSPF area is configured improperly.CThe network wildcard mask is configured improperly.DThe network number is configured improperly.EThe AS is configured improperly.FThe network subnet mask is configured improperly.GAll of the above are likely problems.
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A The network administrator faled to save the configuration.B The configuration register is set to 0x2100.C The boot system flash command is missing from the configuration.D The configuraiton register is set to 0x2102.E The router is configured with the boot system startup command.