Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?() A. Router(config)#router ospf 1B. Router(config)#router ospf 0C. Router(config)#router ospf area 0D. Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E. Router(config-router)#network 192.168.16.0 0.0.0.255 0F. Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?()
A. Router(config)#router ospf 1
B. Router(config)#router ospf 0
C. Router(config)#router ospf area 0
D. Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E. Router(config-router)#network 192.168.16.0 0.0.0.255 0
F. Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
相关考题：
某园区网采用 OSPF路由协议,参与 OSPF的网络地址是 169.111.0.0/16, Cisco路由器的正确配置是 （ ） 。A) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 0.0.0.0 area 0Rounter(config_router)# area o range 169.111.0.0 255.255.0.0B) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 255.255.0.0 area 0Rounter(config-router)# area o range 169.111.0.0 255.255.0.0C) Rounter(config)# router ospf63Rounter(config-router)# network 169.111.0.0 0.0.255.255 area 0Rounter(config_router)# area o range 169.1-11.0.0 255.255.0.0D) Rounter(config)# router ospf63Rounter(config_router)# network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)# area o range 169.111.0.0 0.0.255.255
某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255
RouterAdebug ip ospf events OSPF events debugging is on RouterA 04:43:16: OSPF: Rcv pkt from 10.3.0.2, Ethernet0/1, area 0.0.0.1 mismatch area 0.0.0.2 in the header 04:43:19: OSPF: Rcv hello from 10.100.100.3 area 0 from Ethernet0/0 10.1.0.1 04:43:19: OSPF: End of hello processing Refer to the exhibits. What can be done to fix the problem?（）A. Change router B E0/1 interface to area 0.B. Change router A interface E0/1 to area 0.0.0.2.C. Configure the E0/1 i nterfaces of router A and router B to be in area 0.D. Shut down the E0/1 interfaces in router A and router B as OSPF does not allow back doors between areas.E. Remove the E0/1 interfaces in router A and router B from the OSPF process. Use static rou tes to route data directly from router A to router B to avoid passing data through router C in area 0.
Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?() A. On the ABR router ospf 10 area 3 stubB. On all Area 3 routers router ospf 10 area 3 stubC. On all Area 3 routers router ospf 10 area 3 stub no - summaryD. On the ABR router ospf 10 area 3 nssaE. On the ABR rou ter ospf 10 area 3 stub no - summary
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:TK1(config) router ospf 1TK1(config-router) network 10.10.10.0 255.255.255.0 area 0After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A. The AS is not correctly configuredB. The network subnet mask is incorrectly configuredC. The network wildcard mask is configured incorrectlyD. The network number is not correctly configuredE. The process id is configured incorrectlyF. None of the above
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?() A.Router(config)#router ospf 1B.Router(config)#router ospf 0C.Router(config)#router ospf area 0D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E.Router(config-router)#network 192.168.16.0 0.0.0.255 0F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）A、The AS is not correctly configuredB、The network subnet mask is incorrectly configuredC、The network wildcard mask is configured incorrectlyD、The network number is not correctly configuredE、The process id is configured incorrectlyF、None of the above
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、TestKingRouter(config)# router ospf 0B、TestKingRouter(config)# router ospf 1C、TestKingRouter(config)# router ospf area 0D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）A、Router（config）#router ospf 1B、Router（config）#router ospf 0C、Router（config）#router ospf area 0D、Router（config-router）#network 192.168.16.0 0.0.0.255 area 0E、Router（config-router）#network 192.168.16.0 0.0.0.255 0F、Router（config-router）#network 192.168.16.0 255.255.255.0 area 0
Which OSPF network type is ideal for partially meshed NBMA networks because it is easy to configure（requires no configuration of neighbor commands）， consumes only one IP subnet， and requires no designated router election？
Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）A、Configure a routing process using the command ipv6 router ospf [process-id].B、Add the network statement for the interfaces on which OSPF will run.C、Configure OSPF on the interface that it will run on.D、Use the passive-interface command on the interfaces on which OSPF should not run.E、Enable routing.
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）A、Router(config-router)# network 192.168.10.0 0.0.0.255 0B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D、Router(config)# router ospf 0E、Router(config)# router ospf 1
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）A、CEF was not properly configured.B、OSPF was not properly configured for graceful restart.C、Stateful switchover was not correctly configured.D、NSF for OSPF is only supported in area 0.
什么命令序列将配置一个路由器运行OSPF，并添加网络10.1.1.0/24 area0？（）A、router ospf area 0 network 10.1.1.0 255.255.255.0 area 0B、router ospf network 10.1.1.0 0.0.0.255C、router ospf 1 network 10.1.1.0 0.0.0.255 area 0D、router ospf area 0 network 10.1.1.0 0.0.0.255 area 0E、router ospf network 10.1.1.0 255.255.255.0 area 0F、router ospf 1 network 10.1.1.0 0.0.0.255
多选题Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）ARouter(config-router)# network 192.168.10.0 0.0.0.255 0BRouter(config-router)# network 192.168.10.0 0.0.0.255 area 0CRouter(config-router)# network 192.168.10.0 255.255.255.0 area 0DRouter(config)# router ospf 0ERouter(config)# router ospf 1
问答题Which OSPF network type is ideal for partially meshed NBMA networks because it is easy to configure（requires no configuration of neighbor commands）， consumes only one IP subnet， and requires no designated router election？
单选题某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16，Cisco路由器的正确配置是（ ）。ARounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.0.0 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0BRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 255.255.0.0 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0CRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)#area 0 range 169.111.0.0 255.255.0.0DRounter(config)#router ospf 63Rounter(config-router)#network 169.111.0.0 0.0.255.255 area 0Rounter(config-router)#area 0 range 169.111.0.0 0.0.255.255
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ATestKingRouter(config)# router ospf 0BTestKingRouter(config)# router ospf 1CTestKingRouter(config)# router ospf area 0DTestKingRouter(config)# network 192.168.16.0 0.0.0.255 0ETestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0FTestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
单选题Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）ACEF was not properly configured.BOSPF was not properly configured for graceful restart.CStateful switchover was not correctly configured.DNSF for OSPF is only supported in area 0.
多选题Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
多选题Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）AConfigure a routing process using the command ipv6 router ospf [process-id].BAdd the network statement for the interfaces on which OSPF will run.CConfigure OSPF on the interface that it will run on.DUse the passive-interface command on the interfaces on which OSPF should not run.EEnable routing.
单选题A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0AThe process id is configured improperlyBThe OSPF area is configured improperlyCThe network wildcard mask is configured improperlyDThe network number is configured improperlyEThe AS is configured improperlyFThe network subnet mask is configuerd improperly
多选题Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ARouter(config)#router ospf 1BRouter(config)#router ospf 0CRouter(config)#router ospf area 0DRouter(config-router)#network 192.168.16.0 0.0.0.255 area 0ERouter(config-router)#network 192.168.16.0 0.0.0.255 0FRouter(config-router)#network 192.168.16.0 255.255.255.0 area 0
单选题A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）AThe AS is not correctly configuredBThe network subnet mask is incorrectly configuredCThe network wildcard mask is configured incorrectlyDThe network number is not correctly configuredEThe process id is configured incorrectlyFNone of the above