下列关于JIC中WARNING、CAUTION、NOTE说明正确的是:()A、WARNINGS(警告):可能造成人员伤害B、CAUTIONS(小心):可能造成设备损坏;C、NOTES(注意):注意此说明可以使工作容易操作或补充信息D、以上答案均正确
下列关于JIC中WARNING、CAUTION、NOTE说明正确的是:()
- A、WARNINGS(警告):可能造成人员伤害
- B、CAUTIONS(小心):可能造成设备损坏;
- C、NOTES(注意):注意此说明可以使工作容易操作或补充信息
- D、以上答案均正确
相关考题:
The underlined phrase “draft notice” means ““A. order for army serviceB. train ticket for EuropeC. letter of rejectionD. note of warning
The sign used to caution persons approaching the gangway of a tank barge during cargo transfer reads ______.A.Warning,Keep Off,Stay ClearB.Danger,Do Not BoardC.Warning,No Smoking,No Open Lights,No VisitorsD.Dangerous Cargo Being Transferred
关于LEVEL3警告现象描述正确的是()A、MASTER CAUTION+连续单谐音B、连续单谐音+MASTER WARNINGC、一声单谐音+MASTER WARNNINGD、一声单谐音+MASTER CAUTION
Refer to the output shown on switch SW1 below: Warning: Spantree port fast start should only be enabled on ports connected to a single host.Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporaryspanning tree loops. Use with caution. Spantree ports 4/1-24 fast start enabled. What command could you enter to reproduce this output?
(EMB145)当行李舱门没有正确关闭()A、主注意(caution)和相关信息“BAGGAGE DOOR OPN”被触发B、主警告(warning)和相关信息“BAGGAGE DOOR OPN”被触发C、通知(advisory)信息“BAGGAGE DOOR OPN”显示在EICAS的事件区域D、主注意(caution)和相关信息“BAGGAGE DOOR OPN”未触发
关于启动时提示“Monitor Warning”的叙述,正确的有()A、出现此现象主要是主板BIOS设置不当所致B、“Monitor Warning”是开机时自动对电脑的各项指标进行C、在检测中的第一项就是电压检测D、当电脑的电源输出电压高于CMOS设置的数值时,就会出现此提示
P1板上的WINDSHEAR警告灯何时亮?()A、只在GPWC发出风切变警告时B、在GPWC、WX PWS发出风切变警告时C、在GPWC风切变警告、WX PWS发出风切变WARNING或CAUTION时D、不确定
关于AFDS系统的CAUTION,正确的是:()A、某些CAUTION使P1板上AUTOPILOT灯亮,并能引起A/P断开B、某些CAUTION使P1板上AUTOPILOT灯亮,不会引起A/P断开,但在其工作方式上划一横线C、某些CAUTION只引起P1板上AUTOPILOT灯亮D、上述都正确
在做通告灯测试时()A、MASTER WARNING灯和MASTER CAUTION灯是由通告灯变压器提供6.3V电压B、MASTER WARNING灯和MASTER CAUTION灯是由通告灯变压器提供4.3V电压C、MASTER WARNING灯和MASTER CAUTION灯是由通告灯变压器提供5V电压D、下ECAM页上不会出现巡航页
当将49VU、121VU上的指令器跳开关拔出后,在PTP上:A、显示CIDS FAULT,CAUTION灯亮B、显示CIDS DEGRADATION,CAUTION灯亮C、CAUTION灯不亮D、不确定
问答题Refer to the output shown on switch SW1 below: Warning: Spantree port fast start should only be enabled on ports connected to a single host.Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporaryspanning tree loops. Use with caution. Spantree ports 4/1-24 fast start enabled. What command could you enter to reproduce this output?