Interface ge-0/0/2.0 of your device is attached to the Internet and is configured with an IP address andnetwork mask of 71.33.252.17/24. A webserver with IP address 10.20.20.1 isrunning an HTTP service on TCP port 8080. The webserver is attached to the ge-0/0/0.0 interface of yourdevice. You must use NAT to make the webserver reachable from the Internet using port translation.Which type of NAT must you configure？（）A、source NAT with address shiftingB、pool-based source NATC、static destination NATD、pool-based destination NAT
Interface ge-0/0/2.0 of your device is attached to the Internet and is configured with an IP address andnetwork mask of 71.33.252.17/24. A webserver with IP address 10.20.20.1 isrunning an HTTP service on TCP port 8080. The webserver is attached to the ge-0/0/0.0 interface of yourdevice. You must use NAT to make the webserver reachable from the Internet using port translation.Which type of NAT must you configure？（）
- A、source NAT with address shifting
- B、pool-based source NAT
- C、static destination NAT
- D、pool-based destination NAT
相关考题：
Interface ge-0/0/2.0 of your device is attached to the Internet and is configured with an IP address and network mask of 71.33.252.17/24. A Web server with IP address 10.20.20.1 is running an HTTP service on TCP port 8080. The Web server is attached to the ge-0/0/0.0 interface of your device. You must use NAT to make the Web server reachable from the Internet using port translation.Which type of NAT must you configure?（）A. source NAT with address shiftingB. pool-based source NATC. static destination NATD. pool-based destination NAT
When an SRX series device receives an ESP packet, what happens?() A. If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, it willB. If the destination IP address in the outer IP header of ESP does not match the IP address of the ingress interface, it willC. If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, based packet.D. If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, based of inner header, it will decrypt the packet.
You have two IP addresses configured on the ge-0/0/6 interface, as shown in the exhibit. You want to select the 172.16.10.101 address as the source address for packets sent from this interface to hosts on a remote subnet.Which parameter would you add to the 172.16.10.101 address to complete this task?（）A. preferredB. broadcastC. primaryD. arp 172.16.10.101
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）A. The default gateway is configured on a different subnet form this host.B. The host is a member of the fifth usable subnet of the 192.168.16.0 network.C. The subnetwork address for this host is 192.168.16.160/28.D. The address of the next higher subnet is 192.168.16.192.E. The address of the router interface that is attached to this subnetwork is 192.168.16.190.F. There are 60 usable host addresses on this subnet.
On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?() A. The IP address of the first Fast Ethernet interface.B. The IP address of the console management interface.C. The highest IP address among its active interfaces.D. The lowest IP address among its active interfaces.E. There will be no router ID until a loopback interface is configured.
Refer to the diagram. All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? () A.The subnet mask in use is 255.255.255.192.B.The subnet mask in use is 255.255.255.128.C.The IP address 172.16.1.25 can be assigned to hosts in VLAN1D.The IP address 172.16.1.205 can be assigned to hosts in VLAN1E.The LAN interface of the router is configured with one IP address.F.The LAN interface of the router is configured with multiple IP addresses.
Refer to the exhibit. Which three statements correctly describe Network Device A?() A.With a network wide mask of 255.255.255.128, each interface does not require an IP address.B.With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.C.With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.D.With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.E.With a network wide mask of 255.255.254.0, each interface does not require an IP address.
Your boss is learning a CCNA training course，refer to the exhibit.The access list has been configured on the S0/0 interface of router RTB in the outbound direction.Which two packets，if routed to the interface，will be denied？（）access-list 101 denytcp192.168.15.320.0.0.15any eq telnetaccess-list 101 permitip any anyA.source ip address:192.168.15.5;destination port: 21B.source ip address:,192.168.15.37 destination port: 21C.source ip address:,192.168.15.41 destination port: 21D.source ip address:,192.168.15.36 destination port: 23E.source ip address:192.168.15.46;destination port: 23F.source ip address:,192.168.15.49 destination port: 23
After replacing the NIC card of a PC on the LAN, your Cisco switch shows a new MAC address is attached to that port. Which of the following answer choices below correctly describe a MAC address?（）A、It is a globally unique IP address.B、It is a globally unique 48 bit addressC、It is provided by the manufacturer of the NIC.D、It is used as part of the IPX/SPX configuration.E、It is a logical address.
Which of the following descriptions about IP spoofing is correct？（）A、IP source address is forgedB、IP destination address is forgedC、IP TCP source port is forgedD、IP TCP destination port is forgedE、None of above
Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to an interface（）A、The interface must be configured as a Multilink PPP interface.B、The correct bandwidth should be configured on the interface.C、A QoS policy must not be currently attached to the interface.D、CEF must be enableE、AutoQoS must be enabled globally before it can be enabled on the interface.F、An IP address must be configured on the interface if its speed is equal to or less than 768 kbps.
Interface ge-0/0/2.0 of your router is attached to the Internet and is configured with an IP address and network mask of 71.33.252.17/24. A host with IP address 10.20.20.1 is running an HTTP service on TCP port 8080. This host isattached to the ge-0/0/0.0 interface of your router. You must use interface-based static NAT to make the HTTP service on the host reachable from the Internet. On which IP address and TCP port can Internet hosts reach the HTTP service?（）A、IP address 10.10.10.1 and TCP port 8080B、IP address 71.33.252.17 and TCP port 80C、IP address 71.33.251.19 and TCP port 80D、IP address 71.33.252.19 and TCP port 8080
Interface ge-0/0/2.0 of your device is attached to the Internet and is configured with an IP address and network mask of 71.33.252.17/24. A Web server with IP address 10.20.20.1 is running an HTTP service on TCP port 8080. The Web server is attached to the ge-0/0/0.0 interface of your device. You must use NAT to make the Web server reachable from the Internet using port translation. Which type of NAT must you configure?（）A、source NAT with address shiftingB、pool-based source NATC、static destination NATD、pool-based destination NAT
A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0？（）A、The traffic is droppedB、The resulting action is determined by the destination IP addressC、The source IP address is checked，and，if a match is not found， traffic is routed out interface Serial 1D、The resulting action is determined by the destination IP address and port number
In a cluster using /etc/hosts for name resolution， which of the following describes the minimum requirementsfor the /etc/hosts file？（）A、IP address and IP label of each service and boot interface in the clusterB、IP address and IP label of each service and boot interface in the cluster， loopback interface， and the hostname of the nodeC、IP address and IP label of each service and boot interface in the cluster， the loopbackinterface， and the cluster gatewayD、IP address and IP label of each service and boot interface in the cluster， the loopbackinterface， the cluster gateway， and the subnet network addresses
A two-node cluster is configured for mutual takeover with two service IP labels. The cluster is Being tested for fallover behavior. Both nodes in the cluster have two network interfaces （ent0’ and ’ent1’） configured with IPAT via IP Replacement. When the network cable is removed from the interface card with the service address （’ent0’）， the service address is moved to ’ent1’， and ’ent0’ is reconfigured on its boot address. When the network cable is replaced on ’ent0，the service address does not switch back to ’ent0’. What statement most accurately describes this situation？（） A、 EtherChannel is needed to automatically switch the service IP address back to ’ent0’.B、 This is the default behavior for a network interface failure with this configuration.C、 Gratuitous ARP support needs to be enabled for the IP Network Interface Module in SMIT.D、 The Inactive Network Takeover option should be set to "true" to forece the service addressback to ’ent0’.
You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）A、[edit interfaces]B、[edit security zones]C、[edit system services]D、[edit security interfaces]
Which two commands may be used when configuring an IP address for a Gigabit Ethernet interface?（）A、set interfaces ge-0/0/0.0 address 10.1.1.1/24B、set interfaces ge-0/0/0.0 family inet address 10.1.1.1/24C、set interfaces ge-0/0/0 unit 0 family inet address 10.1.1.1/24D、set interfaces ge-0/0/0 address 10.1.1.1/24
Which command configures an address of 192.168.1.1 with a mask of 255.255.255.0 on interface ge-0/0/0?（）A、set ip interface ge-0/0/0 address 192.168.1.1 255.255.255.0B、set ip interface ge-0/0/0 address 192.168.1.1/24C、set interface ge-0/0/0 ip4 address 192.168.1.1 mask 255.255.255.0D、set interfaces ge-0/0/0 unit 0 family inet address 192.168.1.1/24
When an SRX series device receives an ESP packet, what happens?（）A、If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, it willB、If the destination IP address in the outer IP header of ESP does not match the IP address of the ingress interface, it willC、If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, based packet.D、If the destination address of the outer IP header of the ESP packet matches the IP address of the ingress interface, based of inner header, it will decrypt the packet.
多选题Refer to the diagram. All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? （）AThe subnet mask in use is 255.255.255.192.BThe subnet mask in use is 255.255.255.128.CThe IP address 172.16.1.25 can be assigned to hosts in VLAN1DThe IP address 172.16.1.205 can be assigned to hosts in VLAN1EThe LAN interface of the router is configured with one IP address.FThe LAN interface of the router is configured with multiple IP addresses.
单选题In a cluster using /etc/hosts for name resolution， which of the following describes the minimum requirementsfor the /etc/hosts file？（）AIP address and IP label of each service and boot interface in the clusterBIP address and IP label of each service and boot interface in the cluster， loopback interface， and the hostname of the nodeCIP address and IP label of each service and boot interface in the cluster， the loopbackinterface， and the cluster gatewayDIP address and IP label of each service and boot interface in the cluster， the loopbackinterface， the cluster gateway， and the subnet network addresses
多选题Refer to the exhibit. Which three statements correctly describe Network Device A?（）AWith a network wide mask of 255.255.255.128, each interface does not require an IP address.BWith a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.CWith a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.DWith a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.EWith a network wide mask of 255.255.254.0, each interface does not require an IP address.
多选题A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）AThe default gateway is configured on a different subnet form this host.BThe host is a member of the fifth usable subnet of the 192.168.16.0 network.CThe subnetwork address for this host is 192.168.16.160/28.DThe address of the next higher subnet is 192.168.16.192.EThe address of the router interface that is attached to this subnetwork is 192.168.16.190.FThere are 60 usable host addresses on this subnet.
单选题A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0？（）AThe traffic is droppedBThe resulting action is determined by the destination IP addressCThe source IP address is checked，and，if a match is not found， traffic is routed out interface Serial 1DThe resulting action is determined by the destination IP address and port number
单选题You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）A[edit interfaces]B[edit security zones]C[edit system services]D[edit security interfaces]
单选题Interface ge-0/0/2.0 of your router is attached to the Internet and is configured with an IP address and network mask of 71.33.252.17/24. A host with IP address 10.20.20.1 is running an HTTP service on TCP port 8080. This host isattached to the ge-0/0/0.0 interface of your router. You must use interface-based static NAT to make the HTTP service on the host reachable from the Internet. On which IP address and TCP port can Internet hosts reach the HTTP service?（）AIP address 10.10.10.1 and TCP port 8080BIP address 71.33.252.17 and TCP port 80CIP address 71.33.251.19 and TCP port 80DIP address 71.33.252.19 and TCP port 8080