多选题Refer to the exhibit. Which three statements correctly describe Network Device A?（）AWith a network wide mask of 255.255.255.128, each interface does not require an IP address.BWith a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.CWith a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.DWith a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.EWith a network wide mask of 255.255.254.0, each interface does not require an IP address.
多选题
Refer to the exhibit. Which three statements correctly describe Network Device A?（）
A
With a network wide mask of 255.255.255.128, each interface does not require an IP address.
B
With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
C
With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.
D
With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
E
With a network wide mask of 255.255.254.0, each interface does not require an IP address.
参考解析
解析：
暂无解析
相关考题：
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCP clients connected to the FastEthernet0/1 interface are not receiving addresses.Which two statements contain recommendations that will solve the problem?（）A.The network shown in the output under the ip dhcp pool Central command should be changed to network 10.10.0.0 with a mask of 255.255.255.0B.A second DHCP pool for network 10 .10.0.0/24 should be configuredC.An ip dhcp excluded - address global configuration command for network 10.10.0.0/24 should be issuedD.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/0 c onfigurationE.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/1 configuration
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）A. The default gateway is configured on a different subnet form this host.B. The host is a member of the fifth usable subnet of the 192.168.16.0 network.C. The subnetwork address for this host is 192.168.16.160/28.D. The address of the next higher subnet is 192.168.16.192.E. The address of the router interface that is attached to this subnetwork is 192.168.16.190.F. There are 60 usable host addresses on this subnet.
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A. The Frame Relay encapsulation on the physical interface.B. The local DLCI on each subinterface.C. An IP address on the physical interface.D. The subinterface type as point-to-point.
Which three elements must be used when you configure a router interface for vlan trunking?() A. one IP network or subnetwork for each subinterfaceB. subinterface numbering that matches vlan tagesC. subinterface encapsulation identifiers that match vlan tagsD. a management domain for each subinterfaceE. one physical interface for each subinterfaceF. one subinterface per vlan
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?() A.As numbers must be changed to match on all the routers.B.Loopback interface must be configured so a DR is elected.C.The no auto-summary command is needed on Router A and Router C.D.Router B needs to have two network statements, one for each connected network.
Refer to the diagram. All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? () A.The subnet mask in use is 255.255.255.192.B.The subnet mask in use is 255.255.255.128.C.The IP address 172.16.1.25 can be assigned to hosts in VLAN1D.The IP address 172.16.1.205 can be assigned to hosts in VLAN1E.The LAN interface of the router is configured with one IP address.F.The LAN interface of the router is configured with multiple IP addresses.
Refer to the exhibit. Which three statements correctly describe Network Device A?() A.With a network wide mask of 255.255.255.128, each interface does not require an IP address.B.With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.C.With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.D.With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.E.With a network wide mask of 255.255.254.0, each interface does not require an IP address.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.D、There is no network statement configuration in EIGRP for IPv6.E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive
Which three elements must be used when you configure a router interface for vlan trunking?（）A、one IP network or subnetwork for each subinterfaceB、subinterface numbering that matches vlan tagesC、subinterface encapsulation identifiers that match vlan tagsD、a management domain for each subinterfaceE、one physical interface for each subinterfaceF、one subinterface per vlan
A BGP router is configured as shown below： interface ethernet 0 ip address 10.10.10.1 255.255.0.0! int serial 0 ip address 172.16.1.1 255.255.255.252! router bgp 65001 neighbor 192.168.1.1 remote-as 65002 Based on the above configuration， which of the following BGP statements would inject the10.10.0.0/16 prefix into the BGP routing table？（）A、network 10.0.0.0B、network 10.10.0.0 mask 255.255.0.0C、network 10.10.10.1 mask 255.255.255.255D、network 10.10.10.0 mask 255.255.255.0E、network 10.0.0.0 mask 255.255.0.0
In a cluster using /etc/hosts for name resolution， which of the following describes the minimum requirementsfor the /etc/hosts file？（）A、IP address and IP label of each service and boot interface in the clusterB、IP address and IP label of each service and boot interface in the cluster， loopback interface， and the hostname of the nodeC、IP address and IP label of each service and boot interface in the cluster， the loopbackinterface， and the cluster gatewayD、IP address and IP label of each service and boot interface in the cluster， the loopbackinterface， the cluster gateway， and the subnet network addresses
Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（） A、 A single adapter network using the Network Interface Card in each nodeB、 A single adapter network using persistent addresses on the Network Interface Card in each nodeC、 A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D、 EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
Which two statements are true of a network mask?（）A、A subnet mask specifies the portion of an IP address that is in a binary formatB、A subnet mask specifies the portion of an IP address that is in a decimal formatC、A subnet mask specifies the portion of an IP address that represents a network prefixD、A subnet mask specifies the portion of an IP address that represetns network hosts
Which two statements are true of a network mask?（）A、A subnet mask specifies the portion of an IP address that is in a binary format.B、A subnet mask specifies the portion of an IP address that is in a decimal format.C、A subnet mask specifies the portion of an IP address that represents a network prefix.D、A subnet mask specifies the portion of an IP address that represents network hosts.
多选题You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）AEIGRP for IPv6 is directly configured on the interfaces over which it runs.BEIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.CThere is a network statement configuration in EIGRP for IPv6， the same as for IPv4.DThere is no network statement configuration in EIGRP for IPv6.EWhen a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.FWhen a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive
单选题Which two statements are true of a network mask?（）AA subnet mask specifies the portion of an IP address that is in a binary formatBA subnet mask specifies the portion of an IP address that is in a decimal formatCA subnet mask specifies the portion of an IP address that represents a network prefixDA subnet mask specifies the portion of an IP address that represetns network hosts
多选题Refer to the diagram. All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? （）AThe subnet mask in use is 255.255.255.192.BThe subnet mask in use is 255.255.255.128.CThe IP address 172.16.1.25 can be assigned to hosts in VLAN1DThe IP address 172.16.1.205 can be assigned to hosts in VLAN1EThe LAN interface of the router is configured with one IP address.FThe LAN interface of the router is configured with multiple IP addresses.
单选题In a cluster using /etc/hosts for name resolution， which of the following describes the minimum requirementsfor the /etc/hosts file？（）AIP address and IP label of each service and boot interface in the clusterBIP address and IP label of each service and boot interface in the cluster， loopback interface， and the hostname of the nodeCIP address and IP label of each service and boot interface in the cluster， the loopbackinterface， and the cluster gatewayDIP address and IP label of each service and boot interface in the cluster， the loopbackinterface， the cluster gateway， and the subnet network addresses
单选题You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）AThe Frame Relay encapsulation on the physical interface.BThe local DLCI on each subinterface.CAn IP address on the physical interface.DThe subinterface type as point-to-point.
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router
多选题A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）AThe default gateway is configured on a different subnet form this host.BThe host is a member of the fifth usable subnet of the 192.168.16.0 network.CThe subnetwork address for this host is 192.168.16.160/28.DThe address of the next higher subnet is 192.168.16.192.EThe address of the router interface that is attached to this subnetwork is 192.168.16.190.FThere are 60 usable host addresses on this subnet.
多选题Which two statements are true of a network mask?（）AA subnet mask specifies the portion of an IP address that is in a binary format.BA subnet mask specifies the portion of an IP address that is in a decimal format.CA subnet mask specifies the portion of an IP address that represents a network prefix.DA subnet mask specifies the portion of an IP address that represents network hosts.
多选题Which three elements must be used when you configure a router interface for vlan trunking?（）Aone IP network or subnetwork for each subinterfaceBsubinterface numbering that matches vlan tagesCsubinterface encapsulation identifiers that match vlan tagsDa management domain for each subinterfaceEone physical interface for each subinterfaceFone subinterface per vlan
单选题Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（）A A single adapter network using the Network Interface Card in each nodeB A single adapter network using persistent addresses on the Network Interface Card in each nodeC A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover