A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How canyou accomplish this task，using the fewest physical interfaces and withoutdecreasing networkperformance？（）A、Add two more FastEthernet interfaces.B、Add a second router to handle the vlan traffic.C、Use a hub to connect the four vlans with a FastEthernet interface on router.D、Implement a router-on-a-stick configuration.
A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How canyou accomplish this task，using the fewest physical interfaces and withoutdecreasing networkperformance？（）
- A、Add two more FastEthernet interfaces.
- B、Add a second router to handle the vlan traffic.
- C、Use a hub to connect the four vlans with a FastEthernet interface on router.
- D、Implement a router-on-a-stick configuration.
相关考题：
How can a Ezonexam administrator determine if a router has been configured when it is first powered up?A．A configured router prompts for a passwordB．A configured router goes to the privileged mode promptC．An un configured router goes into the setup dialogD．An un configured router goes to the enable mode prompt
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
Refer to the exhibit. What three statements are true about the IS － IS configuration?() A.The router is in area 49.0001.0002B.The router acts as a Level 1 - 2 routerC.CLNS routing is enable d for the routerD.The router has a system ID of 0003.0004E.The interfaces have a functional IS - IS configurationF.The network service access point selector (NSEL) byte has a value of 0
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? () A. Router A will prefer the path through router B for network 172.20.0.0B. Router A will prefer the path through router C for network 172.20.0.0C. Packets from router D will prefer the path through router B for networks advertised by router AD. Packets from r outer D will prefer the path through router C for networks advertised by router A
Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? () A. Router R2 will be preferred because it has the higher neighbor IP address.B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.C. Router R1 will be preferred because it has a lower local preference.D. Router R2 will be preferred because it has a higher local preference.E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.F. Router R1 will be preferred because it has the lower neighbor IP address.
Above is the output from show ip bgp neighbors command. What is line 21 stating about the BGP connection?() A. the number of consecutive TCP connections to the specified remote neig hborB. the number of total TCP connections that the router hasC. the number of times the router has established a TCP connectionD. the number of neighbors that the router has
Refer to the exhibit. Router RT - 1 and router RT - 2 both advertise network 131.25.0.0/16 to routerRT - 3 via internal BGP. What is the reason that router RT - 3 chose router RT - 1 as its best path tonetwork 131.25.0.0/16.（）A. It has a better router IDB. It advertises a lower autonomous systemC. It advertises t he best AS - pathD. It advertises the best local preferenceE. It advertises the best origin codeF. It advertises the best MED
The Dev － 1 and Dev －3 routers are OSPF neighbors over the Ethernet 0／0 connection. Based on the show ip ospf neighbor output from the Dev － 1 and Dev － 3 routers, which statement is true?() A. Dev - 1 is the DR because it has a lower OSPF router IDB. Dev - 3 is the DR because it has a higher OSPF router priorityC. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priorityD. Dev - 3 is the DR because it has a lower OSPF router IDE. Dev - 1 is the DR because it has a higher OSPF router priority
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）A、The central site router has 100 fully adjacent neighborships with the 100 branchesB、The central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesC、The central site router has a neighborship with the Frame Relay switcHD、None of the other answers is correct
How can an administrator determine if a router has been configured when it is first powered up?（）A、A configured router prompts for a passwordB、A configured router goes to the privileged mode promptC、An un configured router goes into the setup dialogD、An un configured router goes to the enable mode prompt
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
Why is NTP an important component when implementing IPSec VPN in a PKI environment？（）A、 To ensure the router has the correct time when generating its private/public key pairs.B、 To ensure the router has the correct time when checking certificate validity from the remote peersC、 To ensure the router time is sync with the remote peers for encryption keys generationD、 To ensure the router time is sync with the remote peers during theDH exchangeE、 To ensure the router time is sync with the remote peers when generating the cookies during IKE phase 1
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（） B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18A、This router has set the Weight of this route to 10.B、This router's BGP table lists this route as an iBGP route.C、This router's MED has been set to 10.D、This router's BGP table lists an AS_Path length of 10 for this route.
A new router is added to an existing HSRP standby group. One of the existing routers is in anactive state， the other is in a standby state. Under what circumstance will the new router becomethe active router？（）A、The new router will become active immediately because it’s the newest router introduced intothe groupB、The new router can become active only when the existing active router and the existing standbyrouter become unavailableC、The new router has a lower priority valueD、The new router will never become active unless the existing active router becomes unavailableE、The new router has preempt configured and a higher priorityF、The new router has a higher priority value
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
单选题The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）AThe Gallant router has the wrong LMI type configuredBInverse ARP is providing the wrong PVC information to the Gallant routerCThe S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandDThe frame-relay map statement in the Attalla router for the PVC to Steele is not correctEThe IP address on the serial interface of the Attalla router is configured incorrectly
多选题HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？ （）AHSRP provides redundancy and fault toleranceBHSRP allows one router to automatically assume the function of the second router if the second router failsCHSRP allows one router to automatically assume the function of the second router if the second router startsDHSRP provides redundancy and load balancing
单选题A new router is added to an existing HSRP standby group. One of the existing routers is in anactive state， the other is in a standby state. Under what circumstance will the new router becomethe active router？（）AThe new router will become active immediately because it’s the newest router introduced intothe groupBThe new router can become active only when the existing active router and the existing standbyrouter become unavailableCThe new router has a lower priority valueDThe new router will never become active unless the existing active router becomes unavailableEThe new router has preempt configured and a higher priorityFThe new router has a higher priority value
单选题Which router is doing LSA type 7 to type 5 translation，and why？（）ABoth RTA and RTB will do LSA7/5 translation，since they are both NSSA ABRsBRTA will do LSA7/5 translation，since it has the lower router IDCRTB will do LSA7/5 translation，since it has the higher router IDDThe redistributing router will do LSA7/5 translation，since it is within the NSSA
单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）AoneBthreeCtwoDzero
单选题A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）AThere is an error in the router DRAM.BTe IOS image is corrupt.CThe configuration register is set to 0x2142.DThe TFTP server that contains the router configuration file is unreachable.EA boot system configuration command has placed the router into setup mode.
单选题The Testking router is running both RIP and IGRP, and the same route is learned by this router from both of these methods. However, when you issue the command"show ip route" you see only the IGRP route, and not the RIP route. Why is this?（）AIGRP has a faster update timer.BIGRP has a lower administrative distance.CRIP has a higher metric value for that route.DThe IGRP route has fewer hops.EThe RIP path has a routing loop.
单选题How can an administrator determine if a router has been configured when it is first powered up?（）AA configured router prompts for a passwordBA configured router goes to the privileged mode promptCAn un configured router goes into the setup dialogDAn un configured router goes to the enable mode prompt
单选题Why is NTP an important component when implementing IPSec VPN in a PKI environment？（）A To ensure the router has the correct time when generating its private/public key pairs.B To ensure the router has the correct time when checking certificate validity from the remote peersC To ensure the router time is sync with the remote peers for encryption keys generationD To ensure the router time is sync with the remote peers during theDH exchangeE To ensure the router time is sync with the remote peers when generating the cookies during IKE phase 1
单选题A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）AThe central site router has 100 fully adjacent neighborships with the 100 branchesBThe central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesCThe central site router has a neighborship with the Frame Relay switcHDNone of the other answers is correct