Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? () A. Router A will prefer the path through router B for network 172.20.0.0B. Router A will prefer the path through router C for network 172.20.0.0C. Packets from router D will prefer the path through router B for networks advertised by router AD. Packets from r outer D will prefer the path through router C for networks advertised by router A
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? ()
A. Router A will prefer the path through router B for network 172.20.0.0
B. Router A will prefer the path through router C for network 172.20.0.0
C. Packets from router D will prefer the path through router B for networks advertised by router A
D. Packets from r outer D will prefer the path through router C for networks advertised by router A
相关考题：
Which set of configuration commands configures MBGP on the ERX Edge Router?() A. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-selfB. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activateC. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 activeD. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate
Refer to the exhibit. Which of the following statements is true? () A. BGP NSF awareness is enabledB. SSO for BGP NSF capability is enabledC. BGP graceful restart awareness is enabledD. 10.11.1.187 is configured as an NSF-capable BGP neighbor
An engineer has been told to create an implementation plan to influence the choice of best BGP route on a single router using the Weight featurE. The sole Enterprise Internet - connected router, Ent 1, has neighbor relationships with Routers ISP1 and ISP2, which reside inside two different ISPs. The goal is to prefer all routes learned from ISP1 over ISP2 using Weight.Which of the following answers lists a configuration step that would not be usefu l for achieving these goals?（）A. Configuring the neighbor weight command on Ent1.B. Having the ISPs configure the neighbor route - map out command on ISP1 and ISP2, with the route map setting weight.C. Configuring the set weight command inside a route map on Router Ent1.D. Configuring a prefix list to match all class C networks.
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. Which two statements are true?() A. DHCPDISCOVER packets will reach the DHCP server.B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.C. This configuration is applied to interface Fa0/1.D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.F. This configuration is applied to interface Fa0/0.
Refer to the exhibit. What three statements are true about the IS － IS configuration?() A.The router is in area 49.0001.0002B.The router acts as a Level 1 - 2 routerC.CLNS routing is enable d for the routerD.The router has a system ID of 0003.0004E.The interfaces have a functional IS - IS configurationF.The network service access point selector (NSEL) byte has a value of 0
Refer to the exhibit. Which statement is true about the 6.6.6.0／24 prefix?() A. The command neighbor send -community is configured on BGP neighbor 10.10.23.3.B. If another path advertises the 6.6.6.0/24 path and has the default local preference, that path is more preferred.C. Route 6.6.6.0/24 is learned by an IBGP peer.D. The route 10.10.23.3 is not being advertised to other BGP neighbors.
Based on the show ip bgp summary output, which two statements are true?() A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.D. The BGP session to the 10.3.3.3 neighbor is established.E. The BGP session to the 10.2.2.2 neighbor is established.F. The BGP session to the 10.1.1.1 neighbor is established.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?() A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1B. R4(config)# ip default - network 10.0.0.0C. R4(config - router)# default -information originateD. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:Would you like to enter the initial configuration dialog? [yes/no]Why has this occurred?（）A. There is an error in the router DRAM.B. Te IOS image is corrupt.C. The configuration register is set to 0x2142.D. The TFTP server that contains the router configuration file is unreachable.E. A boot system configuration command has placed the router into setup mode.
Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）A.FastEthernet0 /0B.FastEthernet0 /1C.Serial0/0D.Serial0/1.102E.Serial0/1.103F.Serial0/1.104
Refer to the exhibit. What can be determined about the router from the console output?() A.No configuration file was found in NVRAM.B.No configuration file was found in flash.C.No configuration file was found in the PCMCIA card.D.Configuration file is normal and will load in 15 seconds.
Which set of configuration commands configures MBGP on the ERX Edge Router?（）A、router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-selfB、router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activateC、router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 activeD、router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）A、Fa0/0 failsB、The command is rejecteDC、The existing three neighbors failD、The neighborship with 172.16.2.20 fails and then reestablishesE、None of the other answers is correct
Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）A、The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2B、The configuration is invalid because the DHCP options are global configuration commandsC、The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesD、The router will choose which pool to use based upon the interface the DHCP request wasreceived on
单选题Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）A 10.1.1.2B 10.154.154.1C 172.16.5.1D 192.168.5.3
单选题Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configuration statement should be included on router R4 to advertise a default route to its neighbors？（）A R4（config）# ip default-network 10.0.0.0B R4（config）# ip route 0.0.0.0 0.0.0.0 10.1.1.1C R4（config）# ip route 10.0.0.0 255.0.0.0 10.1.1.1D R4（config-router）# default-information originate
单选题A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）AThere is an error in the router DRAM.BTe IOS image is corrupt.CThe configuration register is set to 0x2142.DThe TFTP server that contains the router configuration file is unreachable.EA boot system configuration command has placed the router into setup mode.
多选题Refer to the exhibit. On the basis of the information in the exhibit， which two statements are true？（）AWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2BThe serial 0/0/1 interface on the ISP router has been configured with the set metric 50commandCThe output was generated by entering the show ip bgp command on the SanJose1 routerDThe output was generated by entering the show ip bgp command on the ISP routerEThe serial 0/0/1 interface on the ISP router has been configured with the set metric 75commandFWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
多选题On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）ABOOTPBTFTPCARPDDNSEproxy-ARPFFTPGCDP
多选题An engineer has been told to create an implementation plan to influence the choice of best BGP route on a single router using the Weight featurE. The sole Enterprise Internet - connected router, Ent 1, has neighbor relationships with Routers ISP1 and ISP2, which reside inside two different ISPs. The goal is to prefer all routes learned from ISP1 over ISP2 using Weight. Which of the following answers lists a configuration step that would not be usefu l for achieving these goals?（）AConfiguring the neighbor weight command on Ent1.BHaving the ISPs configure the neighbor route - map out command on ISP1 and ISP2, with the route map setting weight.CConfiguring the set weight command inside a route map on Router Ent1.DConfiguring a prefix list to match all class C networks.
单选题Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）AThe router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2BThe configuration is invalid because the DHCP options are global configuration commandsCThe configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesDThe router will choose which pool to use based upon the interface the DHCP request wasreceived on
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A The network administrator faled to save the configuration.B The configuration register is set to 0x2100.C The boot system flash command is missing from the configuration.D The configuraiton register is set to 0x2102.E The router is configured with the boot system startup command.
单选题Refer to the exhibit. Which statement is true about the 6.6.6.0/24 prefix？（）A If another path advertises the 6.6.6.0/24 path and has the default local preference， that path is more preferredB The command neighbor send-community is configured on BGP neighbor 10.10.23.3C The route 10.10.23.3 is not being advertised to other BGP neighborsD Route 6.6.6.0/24 is learned by an IBGP peer