Your company plans on migrating their network from IPv4 to IPv6 in the near future. Which three techniques can be used to transition from IPv4 to IPv6？（）A、Dual stackB、NATC、Flow labelD、Mobile IPE、6to4 tunnelingF、AnycastG、MBGP
Your company plans on migrating their network from IPv4 to IPv6 in the near future. Which three techniques can be used to transition from IPv4 to IPv6？（）
- A、Dual stack
- B、NAT
- C、Flow label
- D、Mobile IP
- E、6to4 tunneling
- F、Anycast
- G、MBGP
相关考题：
In IPv6 network, an IPv6 overlay tunnel is required to communicate with isolated IPv6 networks across the existing IPv4 infrastructurE. There are currently fiv e IPv6 overlay tunnel types.Which three IPv6 overlay tunnel statements are true？（）A. Overlay tunnels can only be configured between border routers capable of supporting IPv4 and IPv6.B. An manual overlay tunnel supports point - to - multipo int tunnels capable of carrying IPv6 and Connectionless Network Service (CLNS) packets.C. Overlay tunneling encapsulates IPv6 packets in IPv4 packets for delivery across an IPv4 infrastructure.D. Overlay tunnels can be configured between border route rs or between a border router and a host capable of supporting IPv4 and IPv6.E. Cisco IOS supports manual, generic routing encapsulation (GRE), IPv4 - compatible, 6to4, and Intra - Site Automatic Tunnel Addressing Protocol (ISATAP) overlay tunneling mechan isms.F. Cisco IOS supports manual, generic routing encapsulation (GRE), IPv6 - compatible, 4to6, and Multiprotocol Label Switching (MPLS) overlay tunneling mechanisms.
Which statement describes the difference between a manually configured IPv6 in IPv4 tunnel versus an automatic 6to4 tunnel?() A. An automatic 6to4 tunnel does not req uire dual - stack (IPv4 and IPv6) routers at the tunnel endpoints.B. An automatic 6to4 tunnel allows multiple IPv4 destinations.C. A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations.D. A manually configured IPv6 in IPv4 tunnel does not require dual- stack (IPv4 and IPv6) routers at the tunnel endpoints.
Which two statements are true about using IPv4 and IPv6 simultaneously on a network segment? () A. IPv6 allows a host to create its own IPv6 address that will allow it to communicate to other devices on a network configured via DHCP. IPv4 does not provide a similar capability for hosts.B. IPv6 provides for more host IP addresses but IPv4 provides for more network addresses.C. Hosts can be configured to receive both IPv4 and IPv6 addresses via DHCP.D. Host configuration options for IPv4 can be either statically assigned or assigned via DHCP.Host configuration options for IPv6 can be statically assigned only.E. IPv4 and IPv6 addresses c an be simultaneously assigned to a host but not to a router interface.
Your company plans on migrating their network from IPv4 to IPv6 in the near future. Which three techniques can be used to transition from IPv4 to IPv6?() A. Dual stackB. NATC. Flow labelD. Mobile IPE. 6to4 tunnelingF. AnycastG. MBGP
the network administrator has been asked to give reasons for moving from ipv4 to ipv6. what are two valid reasons for adopting ipv6 over ipv4?() A. telnet access does not require a passwordB. natC. no broadcastD. chanage of destination address in the ipv6 headerE. chanage of source address in the ipv6 headerF. autoconfiguration
Which three approaches can be used while migrating from an IPV4 addressing scheme to an IPV6 scheme.() A. statically map IPV4 address to IPV6 addressesB. configuration IPv4 tunnels between IPV6 islandsC. use DHCPv6 to map IPV4 addresses to IPV6 addressesD. use proxying and translation to translate IPV6 packets into IPV4 packetsE. configure IPV6 directlyF. enable dual-stack routing
Which name describes an IPV6 host－enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?() A.dual stackB.dynamicC.TeredoD.Manual 6to4
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?（）A、dual stackB、dynamicC、TeredoD、Manual 6to4
A company is using 6to4 tunneling within their IPv6 network. Which two statements about this kindof tunneling are accurate？（）A、6to4 is a manual tunnel methodB、Prepending a reserved IPv6 code to the hexadecimal representation of 192.168.0.1 facilitates6to4 tunnelingC、Each 6to4 site receives a /48 prefix in a 6to4 tunnelD、2002：：/48 is the address range specifically assigned to 6to4E、Prepending 0x2002 with the IPv4 address creates an IPv6 address that is used in 6to4tunneling
Which two statements are true about using IPv4 and IPv6 simultaneously on a network segment? （）A、IPv6 allows a host to create its own IPv6 address that will allow it to communicate to other devices on a network configured via DHCP. IPv4 does not provide a similar capability for hosts.B、IPv6 provides for more host IP addresses but IPv4 provides for more network addresses.C、Hosts can be configured to receive both IPv4 and IPv6 addresses via DHCP.D、Host configuration options for IPv4 can be either statically assigned or assigned via DHCP.Host configuration options for IPv6 can be statically assigned only.E、IPv4 and IPv6 addresses c an be simultaneously assigned to a host but not to a router interface.
Which statement describes the difference between a manually configured IPv6 in IPv4 tunnel versus an automatic 6to4 tunnel?（）A、An automatic 6to4 tunnel does not req uire dual - stack (IPv4 and IPv6) routers at the tunnel endpoints.B、An automatic 6to4 tunnel allows multiple IPv4 destinations.C、A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations.D、A manually configured IPv6 in IPv4 tunnel does not require dual- stack (IPv4 and IPv6) routers at the tunnel endpoints.
our company is researching a new application that runs over IPv6， but part of it must still have IPv4 support. Your company uses a traditional IPv4 network. Your plan is not to run IPv6 over the whole network， but to segment parts of the network or even to operate simultaneously with IPv6 and IPv4. You must make a brief presentation about IPv6 technology to the board of technical directors. Which three of these items could be part of your presentation？（）A、Tunnel IPv6 over IPv4 to connect far-end IPv6 networks.B、Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possible.C、Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possible.D、What is the meaning of EUI-64 and how does it work？E、Tunnel IPv4 over IPv6 to connect far-end IPv4 networks.
A Company is using 6to4 tunnels in their IPv6 network. Which two statements are true about thesetunnels？（）A、In a 6to4 tunnel， the first two bytes of the IPv6 address will be 0x2002 and the next four byteswill be the hexadecimal equivalent of the IPv4 addressB、In a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the2002：1315：4463：1：：/64 IPv6 addressC、In a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the 2002：c0a8：6301：：/48IPv6 addressD、In a 6to4 tunnel， the first two bytes of the IPv6 address will be locally derived and the next twobytes will be the hexadecimal equivalent of the IPv4 addressE、In a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the 2002：c0a8：6301：：/16IPv6 address
the network administrator has been asked to give reasons for moving from ipv4 to ipv6. what are two valid reasons for adopting ipv6 over ipv4?（）A、telnet access does not require a passwordB、natC、no broadcastD、chanage of destination address in the ipv6 headerE、chanage of source address in the ipv6 headerF、autoconfiguration
Your company is researching a new application that runs over IPv6， but part of it must still have IPv4 support. Your company uses a traditional IPv4 network. Your plan is not to run IPv6 over the whole network， but to segment parts of the network or even to operate simultaneously with IPv6 and IPv4. You must make a brief presentation about IPv6 technology to the board of technical directors. Which three of these items could be part of your presentation？ （）A、 Tunnel IPv6 over IPv4 to connect far-end IPv6 networksB、 Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possibleC、 Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possibleD、 What is the meaning of EUI-64 and how does it work？E、 Tunnel IPv4 over IPv6 to connect far-end IPv4 networks.
Which functionality is required within an IP router that is situated at the boundary of an IPv4 network and an IPv6 network to allow communication between IPv6- only and IPv4 - only nodes?（）A、AutoconfigurationB、Automatic 6to4 TunnelC、Automatic 6to4 RelayD、Network Address Translator - Protocol Translator (NAT - PT)E、Intrasite Automatic T unnel Address Protocol (ISATAP)
Company network is implemting IPv6 into their existing IPv4 netwrok. Which statement is trueabout incorporating IPv6 into an already existing IPv4 network？（）A、Only OSPF version 3 can be utilized for routing IPv4 and IPv6B、IPv4 and IPv6 networks can be routed simultaneouslyC、IPv6 can be routed using the same routing protocol versions as IPv4D、A router routing for IPv6 and IPv4 must convert IPv4 packets to IPv6 packets to route themE、None of the other alternatives apply
Which three approaches can be used while migrating from an IPV4 addressing scheme to an IPV6 scheme?（）A、statically map IPV4 address to IPV6 addressesB、configuration IPv4 tunnels between IPV6 islandsC、use DHCPv6 to map IPV4 addresses to IPV6 addressesD、use proxying and translation to translate IPV6 packets into IPV4 packetsE、configure IPV6 directlyF、enable dual-stack routing
What are three IPv6 transition mechanisms?（）A、6to4 tunnelingB、VPN tunnelingC、GRE tunnelingD、ISATAP tunnelingE、PPP tunnelingF、Teredo tunneling
多选题Your company is researching a new application that runs over IPv6， but part of it must still have IPv4 support. Your company uses a traditional IPv4 network. Your plan is not to run IPv6 over the whole network， but to segment parts of the network or even to operate simultaneously with IPv6 and IPv4. You must make a brief presentation about IPv6 technology to the board of technical directors. Which three of these items could be part of your presentation？ （）ATunnel IPv6 over IPv4 to connect far-end IPv6 networksBExplain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possibleCExplain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possibleDWhat is the meaning of EUI-64 and how does it work？ETunnel IPv4 over IPv6 to connect far-end IPv4 networks.
单选题Company network is implemting IPv6 into their existing IPv4 netwrok. Which statement is trueabout incorporating IPv6 into an already existing IPv4 network？（）AOnly OSPF version 3 can be utilized for routing IPv4 and IPv6BIPv4 and IPv6 networks can be routed simultaneouslyCIPv6 can be routed using the same routing protocol versions as IPv4DA router routing for IPv6 and IPv4 must convert IPv4 packets to IPv6 packets to route themENone of the other alternatives apply
多选题Your company plans on migrating their network from IPv4 to IPv6 in the near future. Which three techniques can be used to transition from IPv4 to IPv6？（）ADual stackBNATCFlow labelDMobile IPE6to4 tunnelingFAnycastGMBGP
多选题Which two statements are true about using IPv4 and IPv6 simultaneously on a network segment? （）AIPv6 allows a host to create its own IPv6 address that will allow it to communicate to other devices on a network configured via DHCP. IPv4 does not provide a similar capability for hosts.BIPv6 provides for more host IP addresses but IPv4 provides for more network addresses.CHosts can be configured to receive both IPv4 and IPv6 addresses via DHCP.DHost configuration options for IPv4 can be either statically assigned or assigned via DHCP.Host configuration options for IPv6 can be statically assigned only.EIPv4 and IPv6 addresses c an be simultaneously assigned to a host but not to a router interface.
多选题The network administrator has been asked to give reasons for moving from ipv4 to ipv6. what are two validreasons for adopting ipv6 over ipv4？（）Atelnet access does not require a passwordBnatCno broadcastDchanage of destination address in the ipv6 headerEchanage of source address in the ipv6 headerFautoconfiguration
多选题A company is using 6to4 tunneling within their IPv6 network. Which two statements about this kindof tunneling are accurate？（）A6to4 is a manual tunnel methodBPrepending a reserved IPv6 code to the hexadecimal representation of 192.168.0.1 facilitates6to4 tunnelingCEach 6to4 site receives a /48 prefix in a 6to4 tunnelD2002：：/48 is the address range specifically assigned to 6to4EPrepending 0x2002 with the IPv4 address creates an IPv6 address that is used in 6to4tunneling
多选题Which three approaches can be used while migrating from an IPV4 addressing scheme to an IPV6 scheme?（）Astatically map IPV4 address to IPV6 addressesBconfiguration IPv4 tunnels between IPV6 islandsCuse DHCPv6 to map IPV4 addresses to IPV6 addressesDuse proxying and translation to translate IPV6 packets into IPV4 packetsEconfigure IPV6 directlyFenable dual-stack routing
多选题A Company is using 6to4 tunnels in their IPv6 network. Which two statements are true about thesetunnels？（）AIn a 6to4 tunnel， the first two bytes of the IPv6 address will be 0x2002 and the next four byteswill be the hexadecimal equivalent of the IPv4 addressBIn a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the2002：1315：4463：1：：/64 IPv6 addressCIn a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the 2002：c0a8：6301：：/48IPv6 addressDIn a 6to4 tunnel， the first two bytes of the IPv6 address will be locally derived and the next twobytes will be the hexadecimal equivalent of the IPv4 addressEIn a 6to4 tunnel， the IPv4 address 192.168.99.1 would be converted to the 2002：c0a8：6301：：/16IPv6 address