Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?() interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 1 tunnel source loopback 1 tunnel destination 192.168.1.2 tunnel mode ipv6ip isatap ipv6 address 2000::/64 eui - 64A、2000::1311:11F F:FE11:1111B、2000::C0A5:101C、2000:C0A5:101::D、2000::5EFE:C0A5:101

Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?() interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 1 tunnel source loopback 1 tunnel destination 192.168.1.2 tunnel mode ipv6ip isatap ipv6 address 2000::/64 eui - 64

  • A、2000::1311:11F F:FE11:1111
  • B、2000::C0A5:101
  • C、2000:C0A5:101::
  • D、2000::5EFE:C0A5:101

相关考题:

以下是路由器R1的部分配置,请完成其配置,或解释配置命令含义。!R1 (Config) interface fastethernet0R1(Config-if) ip address (6) (7)R1(Config-if) (8) (开启端口)!R1 (Config) interface serial 0R1(Config-if) ip address (9) (10)!R1 (Config) ip routingR1 (Config) router rip (11)R1 (Config-router) (12) (声明网络)R1 (Config-router) (13) (声明网络)R1 (Config-router) (14) (声明网络)R1 (Config-router) version 2 (15)!

一台Cisc0路由器R1的第3模块第1端口通过DDN的E1专线与一台远程路由器R2的第4模块第2端口相连,在R1的端口上封装PPP协议。为R1和R2端口分配的IP地址分别为193.42.91.201/30和193.42.91.202/30。下列R2的端口配置,正确的是( )。A.Router(cortfig)#interface s4/2Router(config-if)#bandwidth 2048Router(config-if)#ip address 193.42.91.202 255.255.255.252Router(config-if)#encapsulation PPPRouter(config-if)#exitB.Router(config)#interface a4/2Router(config-if)#bandwidth 2048Router(config-if)#ip address 193.42.91.202 255.255.255.252Router(config-if)#encapsulation PPPRouter(config-if)#exitC.Router(config)#interface s4/2Router(config-if)#bandwidth 2048Router(config-if)#ip address 193.42.91.201 255.255.255.252Router(config-if)#encapsulation hdleRouter(config-if)#exitD.Router(config)#interface a4/2Router(config-if)#bandwidth 2048Router(config-if)#ip address 193.42.91.202 255.255.255.252Router(config-if)#encapsulation hdlcRouter(config-if)#exit

A network technician wants to use a packet analyzer to troubleshoot a reported problem with auser‘s workstation with IP address 192.168.1.45. To identify the workstation‘s packets thetechnician wants to use the workstation‘s MAC address.Which of the following protocols would provide the needed information?()A.DHCPB.ARPC.DNSD.PING

Router R1 lists the following output from a show command. Which of the following is true about R1?()R1 show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456A. R1‘s solicited node multicast address is FF02::1:FF:12:3456.B. R1‘s 2000::4:213:19FF:FE12:3456 address is a global unicast with all 128 bits statically configured.C. Address FF02::2 is R1‘s solicited node multicast.D. R1‘s solicited node multicast, not listed in this output, would be FF02::213:19FF:FE12:3456.

Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? () A.S1(config)# interface fastethernet 0/1S1(config - if)# ip helper - address 10.0.0.2B.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1C.R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1D.R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1E.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1

Refer to the graphic.Host A is communicating with the seiver. What will be the source MAC address of the frames received by Host A from the server?() A.the MAC address of the seiver network interfaceB.the MAC address of host AC.the MAC address of router interface e 1D.the MAC address of router interface e0

Refer to the exhibit. What will Router1 do when it receives the data frame shown?() A.Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.B.Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.C.Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320.D. Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.E.Router1 will forward the data packet out interface FastEthernet0/1.F.Router1 will forward the data packet out interface FastEthernet0/2.

If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network()。 A.R1 will forward the packet out all interfaces.B.R1 will drop this packet because this it is not a valid IP address.C.As R1 forwards the frame containing this packet, Sw-A will add 192.168.1.255 to its MAC table.D.R1 will encapsulate the packet in a frame with a destination MAC address of FF-FF-FF-FF-FF-FFE.As R1 forwards the frame containing this packet, Sw-A will forward it to the device assigned the IP address of 192.168.1.255.

Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request()。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1

Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1()。A、The MAC address of the NIC in Host 1B、The MAC address of the NIC in server 1C、The MAC address of the Fa0/0 interface of router R1D、The MAC address of the s0/0/0 interface of the router R2

Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet()。A、The IP address of sever 1.B、The MAC address of NIC in sever 1.C、The IP address of F0/0 interface of router R1.D、The MAC address of the Fa0/0 interface of router R1.E、The IP address of the s0/0/0 interface of router R2F、The MAC address of the s0/0/0 interface of router R2

Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()A、FEA0::200:FF:FE11:0B、FE80::200:FF:FE11:1111C、FE80::0213:19FF:FE7B:0:1D、FEB0::211:11FF:FE11: 1111

Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?() interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64A、The next hop is 2000::1311:11FF:FE11:1111B、The next hop is FE80::1311:11FF:FE11:1111C、The next hop is FE80::5111:11FF:FE11:1111D、The next hop is 2001::1

What must be configured on the network in order for users on the Internet to view web pages  located on Web Server 2?()A、On router R2, configure a default static route to the 192.168.1.0 network.B、On router R2, configure DNS to resolve the URL assigned to Web Server 2 to the  192.168.1.10 address.C、On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to  192.168.1.10.D、On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24  network to Web Server 2.

Which destination addresses will be used by Host A to send data to Host C?()A、the IP address of Switch 1B、the MAC address of Switch 1C、the IP address of Host CD、the MAC address of Host CE、the IP address of the router's E0 interfaceF、the MAC address of the router's E0 interface

Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission?()A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B、S0/2 may currently be in a state other than up/up.C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D、S0/2 may be configured as a passive inter face.

If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network()。A、R1 will forward the packet out all interfaces.B、R1 will drop this packet because this it is not a valid IP address.C、As R1 forwards the frame containing this packet, Sw-A will add 192.168.1.255 to its MAC table.D、R1 will encapsulate the packet in a frame with a destination MAC address of FF-FF-FF-FF-FF-FFE、As R1 forwards the frame containing this packet, Sw-A will forward it to the device assigned the IP address of 192.168.1.255.

A network technician wants to use a packet analyzer to troubleshoot a reported problem with a user's workstation with IP address 192.168.1.45. To identify the workstation's packets the technician wants to use the workstation's MAC address. Which of the following protocols would provide the needed information?()A、DHCPB、ARPC、DNSD、PING

单选题Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()AFEA0::200:FF:FE11:0BFE80::200:FF:FE11:1111CFE80::0213:19FF:FE7B:0:1DFEB0::211:11FF:FE11: 1111

单选题Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request()。AThe Mac address of the NIC in Sever1BThe IP address of Server 1.CThe MAC address of the s0/0/0 interface of router R2DThe IP address of the s0/0/0 interface of router R1EThe IP address of the Fa0/0 interface of router R1

单选题In the IS-IS Designated Intermediate System (DIS) election process, which criteria is used for DIS selection?()Ahighest router ID first, then highest priorityBhighest MAC address first, then highest priorityChighest router ID first, then highest MAC addressDhighest priority first, then highest router IDEhighest priority first, then highest MAC address

单选题Routers R1 and R2 are configured for HSRP as shown below:   Router R1:   interface ethernet 0   ip address 20.6.2.1 255.255.255.0   standby 35 ip 20.6.2.21   standby 35 priority 100   interface ethernet 1   ip address 20.6.1.1.2 255.255.255.0   standby 34 ip 20.6.1.21    Router R2:   interface ethernet 0   ip address 20.6.2.2 255.255.255.0   standby 35 ip 20.6.2.21   interface ethernet 1   ip address 20.6.1.1.1 255.255.255.0   standby 34 ip 20.6.1.21  standby 34 priority 100   You have configured the routers R1  R2 with HSRP. While debugging router R2 you notice very   frequent HSRP group state transitions.  What is the most likely cause of this? ()A physical layer issuesB no spanning tree loopsC use of non-default HSRP timersD failure to set the command standby 35 preempt

单选题Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1()。AThe MAC address of the NIC in Host 1BThe MAC address of the NIC in server 1CThe MAC address of the Fa0/0 interface of router R1DThe MAC address of the s0/0/0 interface of the router R2

单选题R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1()。AThe frame does not have MAC addresses.BThe source MAC address in the frame is the MAC address of the NIC of Host 1.CThe source MAC address in the frame is the MAC address of the s0/0/0 interface of R1.DThe destination MAC address in the frame is the MAC address of the NICof server 1.EThe destination MAC address in the frame is the MAC address of the s0/0/0 interface of R2

单选题Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet()。AThe IP address of sever 1.BThe MAC address of NIC in sever 1.CThe IP address of F0/0 interface of router R1.DThe MAC address of the Fa0/0 interface of router R1.EThe IP address of the s0/0/0 interface of router R2FThe MAC address of the s0/0/0 interface of router R2

多选题Which destination addresses will be used by Host A to send data to Host C?()Athe IP address of Switch 1Bthe MAC address of Switch 1Cthe IP address of Host CDthe MAC address of Host CEthe IP address of the router's E0 interfaceFthe MAC address of the router's E0 interface

多选题Host 1 has just started up and requests a web page from web server 2. Which two statements describe steps in the process Host 1 uses to send the request to web server 2 (choose two)()。AHost 1 addresses the frames to the MAC address of router R1BHost 1 looks in its ARP cache for the MAC address of router R1CHost 1 addresses the frames to the MAC address of web server 2DHost 1 sends the packets to router R1 to be forwarded to web server 2EHost 1 sends a broadcast ARP request to obtain the MAC address of webserver2

单选题Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?() interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64AThe next hop is 2000::1311:11FF:FE11:1111BThe next hop is FE80::1311:11FF:FE11:1111CThe next hop is FE80::5111:11FF:FE11:1111DThe next hop is 2001::1