Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B、S0/2 may currently be in a state other than up/up.C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D、S0/2 may be configured as a passive inter face.
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）
- A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.
- B、S0/2 may currently be in a state other than up/up.
- C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.
- D、S0/2 may be configured as a passive inter face.
相关考题：
【问题2】（6 分）根据网络拓扑和需求说明，完成路由器R1的配置。R1(config)# interface Serial 1/0R1(config-if)# ip address （3） 255.255.255.0 （设置串口地址）R1(config-if)#no shutdown （开启串口）R1(config)#interface FastEthernet0/0R1(config-if)#ip address （4） 255.255.255.0 （设置以太口地址）R1(config-if)#exitR1(config)#router ospf 1R1(config-router)#network 192.0.0.1 （5） area 0R1(config-router)#network 192.1.1.1 （6） area 0
以下是路由器R1的部分配置，请完成其配置，或解释配置命令含义。!R1 (Config) interface fastethernet0R1(Config-if) ip address (6) (7)R1(Config-if) (8) (开启端口)!R1 (Config) interface serial 0R1(Config-if) ip address (9) (10)!R1 (Config) ip routingR1 (Config) router rip (11)R1 (Config-router) (12) (声明网络)R1 (Config-router) (13) (声明网络)R1 (Config-router) (14) (声明网络)R1 (Config-router) version 2 (15)!
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）A. PPP on the ATM interfaceB. VPI/VCI on the dialer interfaceC. IP address on the ATM interfaceD. CHAP on the dialer interface
Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?() A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? () A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? () A. Router R2 will be preferred because it has the higher neighbor IP address.B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.C. Router R1 will be preferred because it has a lower local preference.D. Router R2 will be preferred because it has a higher local preference.E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.F. Router R1 will be preferred because it has the lower neighbor IP address.
You‘re working at TestKing as a network administrator when your MCSE assistant calls you for help. He has attempted to configure Router TK1 and incorrectly configured the router interface with a subnet broadcast address. You have to correct this by first removing the incorrect IP address and then re-entering the first usable IP address of the same subnet.How will you do this?（）A.B.C.D.E.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）A、BOOTPB、TFTPC、ARPD、DNSE、proxy-ARPF、FTPG、CDP
A network administrator has configured access list 172 to prevent Telnet and ICMP traffic from reaching a server with the address if 192.168.13.26. Which command can the administrator issue to verify that the access list is working properly?（）A、Router# ping 192.168.13.26B、Router# debug access-list 172C、Router# show open ports 192.168.13.26D、Router# show access-listE、Router# show ip interface
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）A、MetricB、Administrative distanceC、Timeout (seconds)D、Prefix lengthE、Interface ID
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）A、Fa0/0 failsB、The command is rejecteDC、The existing three neighbors failD、The neighborship with 172.16.2.20 fails and then reestablishesE、None of the other answers is correct
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enableA、RIPng will be enabled on no interfaces.B、RIPng will be enabled on one interface.C、RIPng will be enabled on two interfaces.D、RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
R1 has 5 working interfaces, with EIGRP neighbors existing off each interface. R1 has routes for subnets 10.1.1.0/24, 10.1.2.0/24, and 10.1.3.0/24, with EIGRP integer metrics of roughly 1 million, 2 million, a nd 3 million, respectively. An engineer then adds the ip summary - address eigrp 1 10.1.0.0 255.255.0.0 command to interface Fa0/0. Which of the following is true?（）A、R1 loses and then reestablishes neighborships with all neighbors.B、R1 no longer advert ises 10.1.1.0/24 to neighbors connected to Fa0/0.C、1 advertises a 10.1.0.0/16 route out Fa0/0, with metric of around 3 million (largest metric of component subnets).D、R1 advertises a 10.1.0.0/16 route out Fa0/0,with metric of around 2 million (med ian metric of component subnets).
多选题Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（） interface f0/0 ipv6 address 2345:0:0:8::1/64A2345:0:0:8::1B2345:0:0:8:0:FF:FE11:1111CFE80::8:0:FF:FE11:1111DFE80:0:0:8::1
单选题The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）AThe Gallant router has the wrong LMI type configuredBInverse ARP is providing the wrong PVC information to the Gallant routerCThe S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandDThe frame-relay map statement in the Attalla router for the PVC to Steele is not correctEThe IP address on the serial interface of the Attalla router is configured incorrectly
单选题Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured. Which combinations accurately describe the interface under which a feature will be configured?（）APPP on the ATM interfaceBVPI/VCI on the dialer interfaceCIP address on the ATM interfaceDCHAP on the dialer interface
多选题On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）ABOOTPBTFTPCARPDDNSEproxy-ARPFFTPGCDP
单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enableARIPng will be enabled on no interfaces.BRIPng will be enabled on one interface.CRIPng will be enabled on two interfaces.DRIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.
单选题Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）AR1 has been configured with an ip default- network 2.0.0.0 command.BR1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.CR1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.DAnother router has been configured with an ip default - network 2.0.0.0 command.EAnother router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
单选题Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）AR1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.BFor any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.CFor any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.DNo subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.