单选题Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64AThe next hop is 2000::1311:11FF:FE11:1111BThe next hop is FE80::1311:11FF:FE11:1111CThe next hop is FE80::5111:11FF:FE11:1111DThe next hop is 2001::1
单选题
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64
A
The next hop is 2000::1311:11FF:FE11:1111
B
The next hop is FE80::1311:11FF:FE11:1111
C
The next hop is FE80::5111:11FF:FE11:1111
D
The next hop is 2001::1
参考解析
解析：
暂无解析
相关考题：
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2‘s F0/0 interface. Which of the following is true about R1‘s route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64A. The next hop is 2000::1311:11FF:FE11:1111B. The next hop is FE80::1311:11FF:FE11:1111C. The next hop is FE80::5111:11FF:FE11:1111D. The next hop is 2001::1
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A. 22B. 11C. 1D. None
The following output occurs on Router R2. Which of the following statements can be confirmed as true based on the output from R2?()R2 show ip policyInterface Route mapFa0／0 RM1Fa0／1 RM2S0／0／0 RM3 A. R2 will forward all packets that enter Fa0/0 per the PBR configuration.B. R2 will use route map RM2 when determining how to forward packets that exit interface Fa0/1.C. R2 will consider using PBR for all packets exiting S0/0 /0 per route map RM3.D. R2 will consider using PBR for all packets entering S0/0/0 per route map RM3.
Routers R1 and R2 are OSPF neighbors using their Fa0/0 interfaces, respectively, using default settings for all timers. An engineer ad ds the ip ospf hello - interval 6 command to R1‘s Fa0/0 configuration.Which of the following is true regarding the results from this change?（）A. The show ip ospf neighbor command on R1 lists the revised Hello timerB. The show ip ospf interfac e brief command on R1 lists the revised Hello timerC. The R1 - R2 neighborship fails due to Hello timer mismatcHD. The show ip ospf interface command on R1 lists the revised Hello timer
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）A. the routes originating from the RIP routing domainB. the routes originating from the OSPF stub areaC. all OSPF inter and intra - area routesD. all routes originating from RIP and OSPF routing domains
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1‘s Fa0/0 configuration.Which of the following is true regarding the results from this c hange？（）A.The show ip eigrp neighbors command on R1 lists the revised Hello timerB.The show ip eigrp interfaces command on R1 lists the revised Hello timerC.The R1 - R2 neighborship fails due to Hello timer mismatcHD.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? () A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A、 physical layer issuesB、 no spanning tree loopsC、 use of non-default HSRP timersD、 failure to set the command standby 35 preempt
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A、22B、11C、1D、None
An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fredA、The configuration is missing one authentication - related configuration commandB、The configuration is missing two authentication - related configuration commandsC、Authentication type 9 is not supported; type 5 should be u sed insteaDD、The key numbers must begin with key 1, so change the key 3 command to key 1
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782.The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A、Router R2 will not form a neighbor relationship with R1.B、Router R2 will obtain a full routing table, including a default route, from R1.C、R2 will obtain OSPF updates from R1, but will not obtain a default route from R1.D、R2 will not have a route for the directly connected serial network, but all other directly connected
The following output occurs on Router R2. Which of the following statements can be confirmed as true based on the output from R2?（） R2# show ip policy Interface Route map Fa0/0 RM1 Fa0/1 RM2 S0/0/0 RM3A、R2 will forward all packets that enter Fa0/0 per the PBR configuration.B、R2 will use route map RM2 when determining how to forward packets that exit interface Fa0/1.C、R2 will consider using PBR for all packets exiting S0/0 /0 per route map RM3.D、R2 will consider using PBR for all packets entering S0/0/0 per route map RM3.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1A、EIGRP works on F0/0 and S0/0/0 without further configurationB、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modEC、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modED、EIGRP for IPv6 needs at least two more configuration commands before it works on R1
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Your company has an IPv4 Ethernet network. A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a segment named Private1. The Private1 segment has a network address of 10.128.4.0/26. Your computer named WKS1 requires access to servers on the Private1 network.The WKS1 computer configuration is as shown in the following table. Network Addresses IPv4 Address 10.128.64.113 Subnet mask 255.255.252.0 Default Gateway 10.128.64.1 The routers are configured as shown in the following table. Router ID Addresses R1 interface 1 R1 interface 2 (To Internet) 10.128.64.1 131.107.108.37 R2 interface 1 R2 interface 2 10.128.64.10 10.128.4.1 WKS1 is unable to connect to the Private1 network by using the current configuration.You need to add a persistent route for the Private1 network to the routing table on WKS1.Which command should you run on WKS1？（）A、Route add -p 10.128.4.0/22 10.128.4.1B、Route add p 10.128.4.0/26 10.128.64.10C、Route add p 10.128.4.0 mask 255.255.255.192 10.128.64.1D、Route add p 10.128.64.10 mask 255.255.255.192 10.128.4.0
单选题Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）AThe show ip eigrp neighbors command on R1 lists the revised Hello timerBThe show ip eigrp interfaces command on R1 lists the revised Hello timerCThe R1 - R2 neighborship fails due to Hello timer mismatcHDThe show ip eigrp interfaces detail command on R1 lists the revised Hello timer
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A physical layer issuesB no spanning tree loopsC use of non-default HSRP timersD failure to set the command standby 35 preempt
单选题Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A22B11C1DNone
单选题An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fredAThe configuration is missing one authentication - related configuration commandBThe configuration is missing two authentication - related configuration commandsCAuthentication type 9 is not supported; type 5 should be u sed insteaDDThe key numbers must begin with key 1, so change the key 3 command to key 1
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）Aphysical layer issuesBno spanning tree loopsCuse of non-default HSRP timersDfailure to set the command standby 35 preempt
单选题Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network. Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）AWhen the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interfaceBWhen routing the packet, matching a route whose outgoing interface is the GRE tunnel interfaceCWhen routing the packet, matching a route whose outgoing interface is the IPsec tunnel interfaceDWhen permitted by an ACL that was referenced in the associated crypto map
单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1AEIGRP works on F0/0 and S0/0/0 without further configurationBEIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modECEIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modEDEIGRP for IPv6 needs at least two more configuration commands before it works on R1