The following was issues on router TestKingA:TestKingA show ip ospf neighborNeigbor ID PRI State Dead Time Address Interface192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1Which type of OSPF network will provide the output shown in the graphic?（）A. FDDIB. nonbroadcast multiaccessC. broadcast multi-accessD. point-to-point
The following was issues on router TestKingA:TestKingA show ip ospf neighborNeigbor ID PRI State Dead Time Address Interface192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1Which type of OSPF network will provide the output shown in the graphic?（）
A. FDDI
B. nonbroadcast multiaccess
C. broadcast multi-access
D. point-to-point
相关考题：
输入哪条命令可以看到以下信息?（ ） LS DataBase Type :Router Ls id :10.1.2.2 Ady rtr :1050 Len :72 Seq :80000008 Cksum (DC) Area Border Router Link count 4 Link id :192.168.2.1 Data :255.255.255.255 Metric:1562 Link id :10.1.2.2 Data :10.1.3.1 Type :Router Metric :1562 Link id :10.1.3.2 Data :255.255.255.255 Type :StubNet Metric :1562A.show ip routeB.show ip ospf isaC.show ip ospf databaseD.show ip ospf interface
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Which of the following can either directly or indirec tly identify all the interfaces for which both 1) OSPF has been enabled and 2) OSPF is not passive?() A. show ip ospf databaseB. show ip ospf interface briefC. show ip protocolsD. show ip route ospfE. show ip ospf neighbors
Refer to the exhibit. Which two Cisco IOS commands on R2 would verify its OSPF neighbor relationships?() A.show ip ospfB.show ip ospf interfaceC.show ip ospf neighborD.show ip ospf databaseE.show ip ospf statisticsF.show running - config begin router ospf
Which BGP command provides the router ID, local preference, next hop, and BGP path in its output?() A. show ip route bgpB. show ip bgpC. show ip bgp neighborsD. show ip bgp summary
The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?() A. show ip ospf [process - id] interfaceB. show ip ospf neighborC. show ip ospf [process - id]D. show ip ospf [process - id area - id] database
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）A. OSPF authentication errors between some of the routersB. Two routers have the same OSPF router IDC. Issues with mistuned OSPF timersD. OSPF LSA pacing issues between some of the routersE. OSPF neighbor adjacency problems between some of the routers
Which one of the following commands will display the placement and direction of an IP access control list on the interfaces of a router?() A. show interface listB. show ip routeC. show ip interfaceD. show ip interface briefE. show interface
Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR／BDR (designated router ／ backup designated router) election process?() A. TK1# show ip ospf interfaceB. TK1# show ip ospf priorityC. TK1# show ospf neighbor detailD. TK1# show ospf processesE. TK1# show ospf neighbor state
Which command will assign the last usable IP address from the 192.168.32.128／28 subnetwork to a router interface?() A. TestKingA(config-if)# ip address 192.168.32.142 255.255.255.240B. TestKingA(config-if)# ip address 192.168.32.143 255.255.255.240C. TestKingA(config-if)# ip address 192.168.32.158 255.255.255.240D. TestKingA(config-if)# ip address 192.168.32.145 255.255.255.240E. TestKingA(config-if)# ip address 192.168.32.144 255.255.255.240
Which is true about OSPF router－id?() A.It is used for type 1 router LSAB.Highest IP address of the loopback is usedC.router-id needs to be matched on ospf neighborsD.router-id is 16 bit
Which is true about OSPF router-id?（）A、It is used for type 1 router LSAB、Highest IP address of the loopback is usedC、router-id needs to be matched on ospf neighborsD、router-id is 16 bit
The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?（）A、show ip ospf [process - id] interfaceB、show ip ospf neighborC、show ip ospf [process - id]D、show ip ospf [process - id area - id] database
Which BGP command provides the router ID, local preference, next hop, and BGP path in its output?（）A、show ip route bgpB、show ip bgpC、show ip bgp neighborsD、show ip bgp summary
The TestKingA router is configured as shown below: TestKingA(config)# interface loopback 0 TestKingA(config-if)# ip address 192.168.16.24 255.255.255.255 As a result of this change, which of the statements below are true?（）A、It creates a virtual, software only, interface.B、It provides a way to test the convergence of OSPF routing updates.C、The mask of 255.255.255.255 is called a host mask.D、It uses a wildcard mask of 255.255.255.255.E、It ensures that an interface is always active for OSPF processes.F、Loopback interfaces must be numbered 0.
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A、show ip routeB、show ip eigrp topologyC、show ip ospf topologyD、show ip eigrp topology 10.1.1.0/24
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode
The following was issues on router TestKingA: TestKingA #show ip ospf neighbor Neigbor ID PRI State Dead Time Address Interface 192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1 Which type of OSPF network will provide the output shown in the graphic?（）A、FDDIB、nonbroadcast multiaccessC、broadcast multi-accessD、point-to-point
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?（）A、OSPF authentication errors between some of the routersB、Two routers have the same OSPF router IDC、Issues with mistuned OSPF timersD、OSPF LSA pacing issues between some of the routersE、OSPF neighbor adjacency problems between some of the routers
输入哪条命令可以看到以下信息？（） LS DataBase Type :Router Ls id :10.1.2.2 Ady rtr :1050 Len :72 Seq# :80000008 Cksum (DC) Area Border Router Link count 4 Link id :192.168.2.1 Data :255.255.255.255 Metric:1562 Link id :10.1.2.2 Data :10.1.3.1 Type :Router Metric :1562 Link id :10.1.3.2 Data :255.255.255.255 Type :StubNet Metric :1562 A、 show ip route B、 show ip ospf isa C、 show ip ospf database D、 show ip ospf interface
Which one of the following commands will display the placement and direction of an IP access control list on the interfaces of a router?（）A、show interface listB、show ip routeC、show ip interfaceD、show ip interface briefE、show interface
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
Which command would display OSPF parameters such as filters， default metric， maximum paths，and number of areas configured on a router？（）A、show ip protocolB、show ip routeC、show ip ospf interfaceD、show ip ospfE、show ip interfaceF、None of the other alternatives apply
Which of the following can either directly or indirec tly identify all the interfaces for which both 1) OSPF has been enabled and 2) OSPF is not passive?（）A、show ip ospf databaseB、show ip ospf interface briefC、show ip protocolsD、show ip route ospfE、show ip ospf neighbors
单选题Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR/BDR (designated router / backup designated router) election process?（）ATK1# show ip ospf interfaceBTK1# show ip ospf priorityCTK1# show ospf neighbor detailDTK1# show ospf processesETK1# show ospf neighbor state
单选题The administrator wants to verify the current state of the OSPF database loading process. Which show command should the administrator use?（）Ashow ip ospf [process - id] interfaceBshow ip ospf neighborCshow ip ospf [process - id]Dshow ip ospf [process - id area - id] database
多选题Which is true about OSPF router-id?（）AIt is used for type 1 router LSABHighest IP address of the loopback is usedCrouter-id needs to be matched on ospf neighborsDrouter-id is 16 bit