The following output was taken from Router R3. A scan of R3‘s configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（）R3show ip ospf interface briefInterface PID Area IP Address/Mask Cost State Nbrs F/CSe0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A. An a uto - cost reference - bandwidth 1000 command in router ospf modeB. An auto - cost reference - bandwidth 2000 command in router ospf modeC. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD. An auto - cost reference - bandwidth 64700 command i n router ospf mode
The following output was taken from Router R3. A scan of R3‘s configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（）R3show ip ospf interface briefInterface PID Area IP Address/Mask Cost State Nbrs F/CSe0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1
A. An a uto - cost reference - bandwidth 1000 command in router ospf mode
B. An auto - cost reference - bandwidth 2000 command in router ospf mode
C. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode
D. An auto - cost reference - bandwidth 64700 command i n router ospf mode
相关考题：
Given the following router output,which configuration file will the router use at its next reload?() A.configB.clientqos.cnfC.startup-configD.running-configuration
Which of the following should an administrator do after running a command from the console onthe perimeter router?() A. Update the configuration logsB. Update the network wiring schematicsC. Update the network configuration proceduresD. Compare the configuration with the baseline
The fol lowing line of output was extracted from the output of the show ip bgp command on Router R1. Which of the following can be determined from this output?（）Network Next Hop Metric LocPrf Weight Path* 130.1.1.0/28 1.1.1.1 0 1 2 3 4 iA. The route is learne d from an eBGP peerB. The route has no more than three ASNs in the AS_PatHC. The route is the best route for this prefixD. None of these facts can be positively determined by this output
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
For the accompanying router output, which of the following statements describes the stat e that neighbor 172.16.254.3 is in?() A. The router will not accept connections from the peer.B. BGP can exchange routing information in this state.C. The router is listening on its server port for connection requests from the peer.D. The router ha s sent out an active TCP connection request to the peer.
Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200?() A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5B. None of the BGP updates that are received on router R2 will ever be received by router R5C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4D. All BGP updates that are received on router R2 will be sent directly to router R5
The output of s how ip eigrp topology on Router R1 shows the following output, which is all the output related to subnet 10.11.1.0/24. How many feasible successor routes does R1 have for 10.11.1.0/24?（）P 10.11.1.0/24, 2 successors, FD is 2172419via 10.1.1.2 (2172423/2 8167), Serial0/0/0.1via 10.1.1.6 (2172423/28167), Serial0/0/0.2A.0B.1C.2D.3
Refer to the exhibit. What can be determined about the router from the console output?() A.No configuration file was found in NVRAM.B.No configuration file was found in flash.C.No configuration file was found in the PCMCIA card.D.Configuration file is normal and will load in 15 seconds.
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）A、Because of damaged flash memory， the router will fail the POSTB、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROMD、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM
An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fredA、The configuration is missing one authentication - related configuration commandB、The configuration is missing two authentication - related configuration commandsC、Authentication type 9 is not supported; type 5 should be u sed insteaDD、The key numbers must begin with key 1, so change the key 3 command to key 1
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。A、Because of damaged flash memory, the router will fail the POST.B、It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.D、It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode
What best describes processing delay？（）A、the time required from receipt of the incoming frame， until the frame/packet has been queued for transmissionB、the time taken for a single packet to traverse the physical medium from one end to the otherC、the time taken to place a frame on the physical medium for transportD、the time spent for a packet to reside in the output queue of a router
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?（） BGP router identifier 11.11.11.11, local AS number 11 ... Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle (Admin) 2.2.2.2 4 3 173 183 41 0 0 00:58:47A、router bgp 11B、neighbor 1.1.1.1 remote- as 11C、neighbor 2.2.2.2 prefix - limit 1D、neighbor 1.1.1.1 shutdown
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（） B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18A、This router has set the Weight of this route to 10.B、This router's BGP table lists this route as an iBGP route.C、This router's MED has been set to 10.D、This router's BGP table lists an AS_Path length of 10 for this route.
The output of s how ip eigrp topology on Router R1 shows the following output, which is all the output related to subnet 10.11.1.0/24. How many feasible successor routes does R1 have for 10.11.1.0/24?（） P 10.11.1.0/24, 2 successors, FD is 2172419 via 10.1.1.2 (2172423/2 8167), Serial0/0/0.1 via 10.1.1.6 (2172423/28167), Serial0/0/0.2A、0B、1C、2D、3
单选题During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。ABecause of damaged flash memory, the router will fail the POST.BIt will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.CIt will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.DIt will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.EIt will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
单选题Given the following router output,which configuration file will the router use at its next reload?（）A configB clientqos.cnfC startup-configD running-configuration
单选题An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fredAThe configuration is missing one authentication - related configuration commandBThe configuration is missing two authentication - related configuration commandsCAuthentication type 9 is not supported; type 5 should be u sed insteaDDThe key numbers must begin with key 1, so change the key 3 command to key 1
单选题The following output occurs on Router R1. Which of the following cannot be determine d from this output?（） R1# show ip route 180.1.1.0 255.255.255.240 Routing entry for 180.1.1.0/28 Known via "bgp 2", distance 20, metric 0 Tag 3, type external Last update from 192.168.1.2 00:10:27 ago Routing Descriptor Blocks: * 192.168.1.2, from 19 2.168.1.2, 00:10:27 ago Route metric is 0, traffic share count is 1 AS Hops 2 Route tag 3AThe type of BGP peer (iBGP or eBGP) that advertised this route to R1BR1's ASNCThe next - hop router's ASNDThe AS_Path length
单选题Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100AThe output describes the contents of a Type 5 LSAB3.3.3.3 identifies a ro uter as being the router performing redistributionCR1's metric for its best route to reach the router with RID 9.9.9.9 is 100DThe router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
单选题The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（） B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18AThis router has set the Weight of this route to 10.BThis router's BGP table lists this route as an iBGP route.CThis router's MED has been set to 10.DThis router's BGP table lists an AS_Path length of 10 for this route.
单选题Which of the following should an administrator do after running a command from the console onthe perimeter router?（）AUpdate the configuration logsBUpdate the network wiring schematicsCUpdate the network configuration proceduresDCompare the configuration with the baseline
多选题The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1AAn a uto - cost reference - bandwidth 1000 command in router ospf modeBAn auto - cost reference - bandwidth 2000 command in router ospf modeCAn ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeDAn auto - cost reference - bandwidth 64700 command i n router ospf mode
单选题The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?（） Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 1.1.1.1 4 1 60 61 26 0 0 00:45:01 0 2.2.2.2 4 3 153 159 26 0 0 00:38:13 1AIdleBOpensentCActiveDEstablished
单选题The fol lowing line of output was extracted from the output of the show ip bgp command on Router R1. Which of the following can be determined from this output?（） Network Next Hop Metric LocPrf Weight Path * 130.1.1.0/28 1.1.1.1 0 1 2 3 4 iAThe route is learne d from an eBGP peerBThe route has no more than three ASNs in the AS_PatHCThe route is the best route for this prefixDNone of these facts can be positively determined by this output
单选题You need to design a method to monitor the security configuration of the IIS server to meet the requirements in the written security policy. What should you do？（）ALog on to a domain controller and run the Resultant Set of Policy wizard in planning mode on the IIS server computer accountBRun the Microsoft Baseline Security Analyzer （MBSA） on the IIS server and scan for vulnerabilities in Windows and IIS checksCRun Security Configuration and Analysis to analyze the IIS server’s security settings by using a custom security templateDOn the IIS server， run the gpresult command from a command prompt and analyze the output
单选题What best describes processing delay？（）Athe time required from receipt of the incoming frame， until the frame/packet has been queued for transmissionBthe time taken for a single packet to traverse the physical medium from one end to the otherCthe time taken to place a frame on the physical medium for transportDthe time spent for a packet to reside in the output queue of a router