多选题Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority？ （）APort priority value can be configured between 1 and 65535.BA higher port priority value means a higher priority of LACP.CPort priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.DLACP uses the port priority with the port number to form the port identifier.ELACP Port priority default value should always be changed
多选题
Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority？ （）
A
Port priority value can be configured between 1 and 65535.
B
A higher port priority value means a higher priority of LACP.
C
Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
D
LACP uses the port priority with the port number to form the port identifier.
E
LACP Port priority default value should always be changed
参考解析
解析：
暂无解析
相关考题：
要启用LACP并将交换机端口加入端口信道1,可使用下面哪两个命令之一?() A.Switch(config)#interface port-channel1B.Switch(config)#channel-group 1 mode activeC.Switch#interface port-channel 1D.Switch(config-if)#channel-group 1 mode active
Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port
Anetworkadministratormustconfigure200switchportstoaccepttrafficfromonlythecurrentlyattachedhostdevices.WhatwouldbethemostefficientwaytoconfigureMAC－levelsecurityonalltheseports?() A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.C.Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
You are about to migrate a customer network to use a VSS. Which of these statements is true about a VSS？ （）A、 The VSS switch must be the root bridge for all VLANs and is automatically designatedB、 The VSS switch is defined in RFC 4318 as a managed objectC、 The PAgP+ or LACP protocols are used to maintain the operational state of the VSS devicesD、 A VSS interoperates with a virtual port channelE、 The 802.1Q or ISL protocols are used to maintain the operational state of the VSS devicesF、 A VSS increases the size of the spanning-tree domain
Which three are valid methods to monitor and trend SAN port channels with DCNM？（）A、 use summary view in the device managerB、 from the DCNM-SAN client， view ISLs in real time from the Performance drop-down listC、 for each port channel， select Monitor ContinuallyD、 configure traps for each port channel to utilize RMONE、 set up flows with the DCNM-SAN client and use the Performance Manager web client for performance collections
Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（） A、 Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B、 Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C、 Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D、 Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
在没有乳糖的培养基中，（）种E.coli不产生β-半乳糖苷酶。A、lacI+lacP+lacO+lacZ+B、lacI-lacP+lacO+lacZ+C、lacI+lacP+lacOclacZ+D、lacI-lacP+lacOclacZ+
7342 OLT以下命令配置的是network1，3口的静态LACP？# configure la-agg-port 1 actor-key 1 aggregatable aggregatable active-lacp active-lacp lacp-mode manual# configure la-agg-port 3 actor-key 1 aggregatable aggregatable active-lacp active-lacp lacp-mode manual
# configure la-agg-port 1 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp # configure la-agg-port 5 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp
Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority？ （）A、 Port priority value can be configured between 1 and 65535.B、 A higher port priority value means a higher priority of LACP.C、 Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.D、 LACP uses the port priority with the port number to form the port identifier.E、 LACP Port priority default value should always be changed
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）A、LACP is used to connect to non-Cisco devices.B、LACP packets are sent with the command channel-group 1 mode desirable.C、LACP packets are sent with the command channel-group 1 mode active.D、Standby interfaces should be configured with a higher priority.E、Standby interfaces should be configured with a lower priority.
n1kv-l3（config）# show lacp offload status Current Status ： Enabled Running Config Status ： Enabled Saved Config Status ： Disabled What two facts does the output signify？ （）A、 LACP is enabled on the Nexus 1000v.B、 LACP will be offloaded to the upstream switch.C、 LACP will be negotiated to the VM.D、 LACP is negotiated by the VSM.E、 LACP is negotiated by the VEM in all instances.
When you enable port security on an interface that is also configured with a voice VLAN， what is the maximum number of secure MAC addresses that should be set on the port？（）A、No more than one secure MAC address should be set.B、The default will be set.C、The IP phone should use a dedicated port， therefore only one MAC address is needed per port.D、No value is needed if the switchport priority extend command is configured. E、No more than two secure MAC addresses should be set.
The above bgp configuration has what effect on the configured router？（）A、Allows incoming TCP connections destined to port 179B、Allows incoming TCP connections sourced from port 179C、Allows incoming TCP connections from 1.1.1.1 and destined to，or sourced from port 179D、Allows incoming TCP connections from 1.1.1.1 that are destined to port 179E、Allows incoming TCP connections from 1.1.1.1 that are sourced from port 179
When configuring unified ports on a 5548 switch， which port ordering must be respected？（）A、 Fibre Channel ports must be configured from the first port in the module.B、 Ethernet ports must be configured from the last port in the module.C、 Fibre Channel ports must be configured from the last port in the module.D、 Ethernet ports must be configured from the first port in the module.
The Company LAN switches are being configured to support the use of Dynamic VLANs. What should be considered when implementing a dynamic VLAN solution？（）A、Each switch port is assigned to a specific VLAN.B、Dynamic VLANs require a VLAN Membership Policy Server.C、Devices are in the same VLAN regardless of which port they attach to.D、Dynamic VLAN assignments are made through the command line interface.
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）A、 The fabric interconnects must be in end-host mode.B、 A pin group must be configured on the server tab in Cisco UCS Manager.C、 In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.D、 Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.E、 Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
You need to configure port security on switch R1. Which two statements are true about this technology？ （）A、 Port security can be configured for ports supporting VoIP.B、 With port security configured， four MAC addresses are allowed by default.C、 The network administrator must manually enter the MAC address for each device in order for the switch to allow connectivity.D、Withsecurity configured， only one MAC addresses is allowed by default. E、 Port security cannot be configured for ports supporting VoIP.
You are the network administrator for your company. The network consists of a single Active Directory domain. All computers on the network are members of the domain. You administer a Network Load Balancing cluster that consists of three nodes. Each node runs Windows Server 2003 and contains a single network adapter. The Network Load Balancing cluster can run only in unicast mode. The Network Load Balancing cluster has converged successfully. To increase the utilization of the cluster， you decide to move a particular application to each node of the cluster. For this application to run， you must add a Network Load Balancing port rule to the nodes of the cluster. You start Network Load Balancing Manager on the second node of the cluster. However， Network Load Balancing Manager displays a message that it cannot communicate with the other two nodes of the cluster. You want to add the port rule to the nodes of the cluster. What should you do？ （）A、 Use Network Load Balancing Manager on the Network Load Balancing default host to add the port rule.B、 Change the host priority of the second node to be the highest in the cluster， and then use Network Load Balancing Manager to add the port rule.C、 Run the nlb.exe drain command on each node， and then use Network Load Balancing Manager to add the port rule.D、 Add the port rule through Network Connections Properties on each node.
You are the Exchange administrator of the Xxx Corporation’s Exchange 2010 organization.You have configured a Database Availability Group （DAG） named DAG01.You need to change the replication port used by the DAG.What are two things that you must do？（）A、Use the Exchange Management Console （EMC） to change the TCP port used for replication.B、Use the Exchange Management Shell to change the TCP port used for replication.C、Modify the Windows Firewall exceptions on each member of the DAG to open the replication port.D、Modify the Windows Firewall exceptions on the witness server of the DAG to open the replication port.E、Use the Exchange Management Shell to configure the DAG IP address of 0.0.0.0.F、Use the Exchange Management Shell to change the DAG IP address to 127.0.0.1.
多选题Each port that is configured to use LACP has an LACP port priority. Which statements are true about LACP port priority？ （）APort priority value can be configured between 1 and 65535.BA higher port priority value means a higher priority of LACP.CPort priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.DLACP uses the port priority with the port number to form the port identifier.ELACP Port priority default value should always be changed
单选题Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（）A Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
多选题Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch？（）ASW1#show swithport port-security interface FastEthernet 0/12BSW1# show swithport port-secure interface FastEthernet 0/12CSW1# show port-secure interface FastEthernet 0/12DSW1#show running-configESW1#show port-security interface FastEthernet 0/12
单选题Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）ATrunkBIsolatedCPrimaryDCommunityEPromiscuousFNone of the other alternatives apply
单选题在没有乳糖的培养基中，（）种E.coli不产生β-半乳糖苷酶。AlacI+lacP+lacO+lacZ+BlacI-lacP+lacO+lacZ+ClacI+lacP+lacOclacZ+DlacI-lacP+lacOclacZ+
单选题When you enable port security on an interface that is also configured with a voice VLAN， what is the maximum number of secure MAC addresses that should be set on the port？（）ANo more than one secure MAC address should be set.BThe default will be set.CThe IP phone should use a dedicated port， therefore only one MAC address is needed per port.DNo value is needed if the switchport priority extend command is configured. ENo more than two secure MAC addresses should be set.