Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2‘s F0/0 interface. Which of the following is true about R1‘s route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64A. The next hop is 2000::1311:11FF:FE11:1111B. The next hop is FE80::1311:11FF:FE11:1111C. The next hop is FE80::5111:11FF:FE11:1111D. The next hop is 2001::1
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2‘s F0/0 interface. Which of the following is true about R1‘s route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
A. The next hop is 2000::1311:11FF:FE11:1111
B. The next hop is FE80::1311:11FF:FE11:1111
C. The next hop is FE80::5111:11FF:FE11:1111
D. The next hop is 2001::1
相关考题：
There are three routers on a Gigabit Ethernet LAN: Router A, Router B, and Router C. Router A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A‘s DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80.Which statement is true?（）A. Router A remains the DIS and generates a new pseudonode LSP for that LANB. Router A remains the DIS and NO new pseudonode LSP is generated for that LANC. Router D becomes the new DIS, generates a new pseudonode LSP for that LAN, and purges the old pseudonode LSP generated by Router AD. Router D becomes the new DIS, does NOT generate a new pseudonode LSP for that LAN, and does NOT purge the old pseudonode LSP generated by Router A
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router‘s logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interfaceB. When routing the packet, matching a route whose outgoing interface is the GRE tunnel interfaceC. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interfaceD. When permitted by an ACL that was referenced in the associated crypto map
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200?() A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5B. None of the BGP updates that are received on router R2 will ever be received by router R5C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4D. All BGP updates that are received on router R2 will be sent directly to router R5
The Dev － 1 and Dev －3 routers are OSPF neighbors over the Ethernet 0／0 connection. Based on the show ip ospf neighbor output from the Dev － 1 and Dev － 3 routers, which statement is true?() A. Dev - 1 is the DR because it has a lower OSPF router IDB. Dev - 3 is the DR because it has a higher OSPF router priorityC. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priorityD. Dev - 3 is the DR because it has a lower OSPF router IDE. Dev - 1 is the DR because it has a higher OSPF router priority
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? () A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）A、router bgp 2B、router bgp 1C、neighbor 10.1 .1.2 remote - as 2D、neighbor 10.1.1.2 Update - source 10.1.1.1E、neighbor 10.1.1.2 Update- source S0/0
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
You are given a PC, a router, and a cable. Select the correct combination that will allow you to log into the router locally using a terminal emulation program such as HyperTerminal.（）A、Connect the PC's COM port to the router's console port using a straight-through cable.B、Connect the PC's COM port to the router's console port using a rollover cable.C、Connect the PC's COM port to the router's ethernet port using a straight-through cable.D、Connect the PC's ethernet port to the router's ethernet port using a rollover cable.E、Connect the PC's ethernet port to the router's ethernet port using a straight- through cable.
In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64A、The next hop is 2000::1311:11FF:FE11:1111B、The next hop is FE80::1311:11FF:FE11:1111C、The next hop is FE80::5111:11FF:FE11:1111D、The next hop is 2001::1
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A、The Popcorn router is not forwarding RIP updates.B、The Popcorn router did not include network 192.168.12.0 in its routing configuration.C、The Ethernet1 interface of the Popcorn router is shutdown.D、The clockrate is not present in the configuration of one of the routers.E、The Serial interface of the Popcorn router is not operating.
There are three routers on a Gigabit Ethernet LAN: Router A, Router B, and Router C. Router A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A's DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80. Which statement is true?（）A、Router A remains the DIS and generates a new pseudonode LSP for that LANB、Router A remains the DIS and NO new pseudonode LSP is generated for that LANC、Router D becomes the new DIS, generates a new pseudonode LSP for that LAN, and purges the old pseudonode LSP generated by Router AD、Router D becomes the new DIS, does NOT generate a new pseudonode LSP for that LAN, and does NOT purge the old pseudonode LSP generated by Router A
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A physical layer issuesB no spanning tree loopsC use of non-default HSRP timersD failure to set the command standby 35 preempt
多选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）Arouter bgp 2Brouter bgp 1Cneighbor 10.1 .1.2 remote - as 2Dneighbor 10.1.1.2 Update - source 10.1.1.1Eneighbor 10.1.1.2 Update- source S0/0
多选题The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）AThe Popcorn router is not forwarding RIP updates.BThe Popcorn router did not include network 192.168.12.0 in its routing configuration.CThe Ethernet1 interface of the Popcorn router is shutdown.DThe clockrate is not present in the configuration of one of the routers.EThe Serial interface of the Popcorn router is not operating.
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）Aphysical layer issuesBno spanning tree loopsCuse of non-default HSRP timersDfailure to set the command standby 35 preempt
单选题There are three routers on a Gigabit Ethernet LAN: Router A, Router B, and Router C. Router A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A's DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80. Which statement is true?（）ARouter A remains the DIS and generates a new pseudonode LSP for that LANBRouter A remains the DIS and NO new pseudonode LSP is generated for that LANCRouter D becomes the new DIS, generates a new pseudonode LSP for that LAN, and purges the old pseudonode LSP generated by Router ADRouter D becomes the new DIS, does NOT generate a new pseudonode LSP for that LAN, and does NOT purge the old pseudonode LSP generated by Router A
单选题Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network. Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）AWhen the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interfaceBWhen routing the packet, matching a route whose outgoing interface is the GRE tunnel interfaceCWhen routing the packet, matching a route whose outgoing interface is the IPsec tunnel interfaceDWhen permitted by an ACL that was referenced in the associated crypto map
单选题Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64AThe next hop is 2000::1311:11FF:FE11:1111BThe next hop is FE80::1311:11FF:FE11:1111CThe next hop is FE80::5111:11FF:FE11:1111DThe next hop is 2001::1
多选题Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command. Which of the following commands must have been configur ed on R1's Fa0/0 interface?（）Aip ospf authentication nullBip ospf authentication message - digestCip ospf authentication -key whatever- it - isDip ospf message - digest - key 1 md5 whatever - it - isEip ospf md5 1 key whatever - it - is
单选题There are three IS-IS routers on a Gigabit Ethernet segment: Router A, Router B, and Router C. Each router is configured in the same area and each routers Gigabit Ethernet interface is configured for Level 1-only. Router A is the Designated Intermediate System (DIS). Each routers IP address on that segment is: Router A: 10.1.1.1/24 Router B: 10.1.1.2/24 Router C: 10.2.2.1/26 Which statement is true about all the adjacencies that exist on that LAN?（）ANo routers are adjacent with each other.BOnly Router A and Router B are adjacent at Level 1.COnly Router A and Router B are adjacent at Level 2.DAll three routers are adjacent with each other at Level 1.