What will a router do during startup if a configuration file is not located in NVRAM?() A. it will search for the configuration file in the locations specified by boot system commands.B. it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D. it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
What will a router do during startup if a configuration file is not located in NVRAM?()
A. it will search for the configuration file in the locations specified by boot system commands.
B. it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.
C. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.
D. it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.
E. it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
相关考题：
After working all night and successfully configuring a Cisco router for the Ezonexam network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?A．Hardware failure in NVRAM prevents the router from loading the configB．Startup-config in flash is corrupt and cannot be analyzedC．Router configuration-register set to bypass startup configurationD．Startup-config in NVRAM is corrupt and cannot be analyzedE．None of the above
What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?A．It will search for the configuration file in the locations specified by boot system commands.B．It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D．It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
You just purchased a refurbished router that contains a configuration from a previous deployment. What should you do, before entering a new configuration into the router?() A. RAM should be erased and the router restarted.B. Flash should be erased and the router restarted.C. NVRAM should be erased and the router restarted.D. The new configuration should be entered and saved.
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A. Flash,TFTP server,ROMB. Flash,NVRAM,ROMC. ROM,NVRAM,TFTP serverD. NVRAM,TFTP server,ROME. TFTP server,Flash,NVRAM
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A.Flash,TFTPserver,ROMB.Flash,NVRAM,ROMC.ROM,NVRAM,TFTP serverD.NVRAM,TFTP server,ROME.TFTP server,Flash,NVRAM
There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload?() A.Flash，TFTPserver，ROMB.Flash，NVRAM，ROMC.ROM，NVRAM，TFTPserverD.NVRAM，TFTPserver，ROME.TFTPserver，Flash，NVRAM
There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload()。 A.TFTP server, Flash, NVRAMB.ROM, NVRAM, TFTP serverC.NVRAM, TFTP server, ROMD.Flash, TFTP server, ROME.Flash, NVRAM, ROM
Refer to the exhibit. What can be determined about the router from the console output?() A.No configuration file was found in NVRAM.B.No configuration file was found in flash.C.No configuration file was found in the PCMCIA card.D.Configuration file is normal and will load in 15 seconds.
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）A、Because of damaged flash memory， the router will fail the POSTB、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROMD、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM
What does a configuration Register Setting of 0x2105 indicate to the Router? （）A、The Boot IOS Code is Located in the NVRAM.B、Check NVRAM for boot system Commands.C、Bypass NVRAM Configurations.D、Boot the IOS Code Located in ROM.E、Perform a Password Recovery.F、Bypass The Code In ROM.
During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。A、Because of damaged flash memory, the router will fail the POST.B、It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.C、It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.D、It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.E、It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
What will a router do during startup if a configuration file is not located in NVRAM?（）A、it will search for the configuration file in the locations specified by boot system commands.B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.
After working all night and successfully configuring a Cisco router for the TestKing network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode! Which of the choices below indicates the source of your problem?（）A、Hardware failure in NVRAM prevents the router from loading the configB、Startup-config in flash is corrupt and cannot be analyzedC、Router configuration-register set to bypass startup configurationD、Startup-config in NVRAM is corrupt and cannot be analyzedE、None of the above
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）A、Flash,TFTPserver,ROMB、Flash,NVRAM,ROMC、ROM,NVRAM,TFTP serverD、NVRAM,TFTP server,ROME、TFTP server,Flash,NVRAM
You just purchased a refurbished router that contains a configuration from a previous deployment. What should you do, before entering a new configuration into the router?（）A、RAM should be erased and the router restarted.B、Flash should be erased and the router restarted.C、NVRAM should be erased and the router restarted.D、The new configuration should be entered and saved.
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequencethat router will use to find an ios during reload？（）A、Flash，TFTP server，ROMB、Flash，NVRAM，ROMC、ROM，NVRAM，TFTP serverD、NVRAM，TFTP server，ROME、TFTP server，Flash，NVRAM
There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload?（）A、TFTP server, Flash, NVRAMB、ROM, NVRAM, TFTP serverC、NVRAM, TFTP server, ROMD、Flash, TFTP server, ROME、Flash, NVRAM, ROM
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next？（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload？（）A、Flash，TFTPserver，ROMB、Flash，NVRAM，ROMC、ROM，NVRAM，TFTPserverD、NVRAM，TFTPserver，ROME、TFTPserver，Flash，NVRAM
单选题During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。ABecause of damaged flash memory, the router will fail the POST.BIt will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.CIt will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.DIt will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.EIt will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.
单选题There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）AFlash,TFTPserver,ROMBFlash,NVRAM,ROMCROM,NVRAM,TFTP serverDNVRAM,TFTP server,ROMETFTP server,Flash,NVRAM
单选题There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）AFlash,TFTP server,ROMBFlash,NVRAM,ROMCROM,NVRAM,TFTP serverDNVRAM,TFTP server,ROMETFTP server,Flash,NVRAM
单选题There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload?（）ATFTP server, Flash, NVRAMBROM, NVRAM, TFTP serverCNVRAM, TFTP server, ROMDFlash, TFTP server, ROMEFlash, NVRAM, ROM
单选题There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload？（）AFlash，TFTPserver，ROMBFlash，NVRAM，ROMCROM，NVRAM，TFTPserverDNVRAM，TFTPserver，ROMETFTPserver，Flash，NVRAM
单选题A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next?（）AIt checks the configuration registerBIt attempts to boot from a TFTP serverCIt loads the first image file in flash memoryDIt inspects the configuration file in NVRAM for boot instructions
单选题A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOSimage.what function does the router perform next?（）AIt checks the configuration registerBIt attempts to boot from a TFTP serverCIt loads the first image file in flash memoryDIt inspects the configuration file in NVRAM for boot instructions
单选题What does a configuration Register Setting of 0x2105 indicate to the Router? （）AThe Boot IOS Code is Located in the NVRAM.BCheck NVRAM for boot system Commands.CBypass NVRAM Configurations.DBoot the IOS Code Located in ROM.EPerform a Password Recovery.FBypass The Code In ROM.