There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload?() A.Flash，TFTPserver，ROMB.Flash，NVRAM，ROMC.ROM，NVRAM，TFTPserverD.NVRAM，TFTPserver，ROME.TFTPserver，Flash，NVRAM
There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload?()
A.Flash，TFTPserver，ROM
B.Flash，NVRAM，ROM
C.ROM，NVRAM，TFTPserver
D.NVRAM，TFTPserver，ROM
E.TFTPserver，Flash，NVRAM
相关考题：
What will cause a Ezonexam router to enter setup mode? (Choose two)A. The configuration file is missing in NVRAM.B. The configuration register is set to 0x2100.C. Boot system commands are misconfigured in the running-configuration.D. The setup command was issued from the privileged mode prompt.E. The IOS is missing.F. The IOS is corrupt.
Given the following router output,which configuration file will the router use at its next reload?() A.configB.clientqos.cnfC.startup-configD.running-configuration
During the boot sequence, a Ezonexam 2800 series router needs to locate and load an operating system. What is the default order the router uses to find an operating system?A．ROM, TFTP server, FlashB．Flash, TFTP server, ROMC．Flash, NVRAM, TFTP serverD．Flash, ROM, TFTP serverE．Flash, TFTP server, RAM
If NVRAM lacks boot system commands, where does the router look for the Cisco IOS by default?() A.ROMB.RAMC.FlashD.BootstrapE.Startup-.config
After making changes to the router, you issue the copy running-config startup-config command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）A. The NVRAM is corrupted.B. The boot system commands were omitted in the configuration.C. The configuration register setting is incorrect.D. The upgraded configuration incompatible with the hardware platform.E. The upgraded IOS incompatible with the hardware.
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A. Flash,TFTP server,ROMB. Flash,NVRAM,ROMC. ROM,NVRAM,TFTP serverD. NVRAM,TFTP server,ROME. TFTP server,Flash,NVRAM
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?() A.Flash,TFTPserver,ROMB.Flash,NVRAM,ROMC.ROM,NVRAM,TFTP serverD.NVRAM,TFTP server,ROME.TFTP server,Flash,NVRAM
There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload()。 A.TFTP server, Flash, NVRAMB.ROM, NVRAM, TFTP serverC.NVRAM, TFTP server, ROMD.Flash, TFTP server, ROME.Flash, NVRAM, ROM
What does a configuration Register Setting of 0x2105 indicate to the Router? （）A、The Boot IOS Code is Located in the NVRAM.B、Check NVRAM for boot system Commands.C、Bypass NVRAM Configurations.D、Boot the IOS Code Located in ROM.E、Perform a Password Recovery.F、Bypass The Code In ROM.
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）A、Flash,TFTP server,ROMB、Flash,NVRAM,ROMC、ROM,NVRAM,TFTP serverD、NVRAM,TFTP server,ROME、TFTP server,Flash,NVRAM
Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）A、The router will enter setup mode.B、The router will enter ROM monitor mode.C、The router will enter global configuration mode.D、The boot will hang until an IOS is available.
A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?（）A、It checks the configuration register.B、It attempts to boot from a TFTP server.C、It loads the first image file in flash memory.D、It inspects the configuration file in NVRAM for boot instructions.
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）A、The NVRAM is corrupted.B、The boot system commands were omitted in the configuration.C、The configuration register setting is incorrect.D、The upgraded configuration incompatible with the hardware platform.E、The upgraded IOS incompatible with the hardware.
There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）A、Flash,TFTPserver,ROMB、Flash,NVRAM,ROMC、ROM,NVRAM,TFTP serverD、NVRAM,TFTP server,ROME、TFTP server,Flash,NVRAM
There are no boot system commands in a router configuration in NVRAM.What is the fallback sequencethat router will use to find an ios during reload？（）A、Flash，TFTP server，ROMB、Flash，NVRAM，ROMC、ROM，NVRAM，TFTP serverD、NVRAM，TFTP server，ROME、TFTP server，Flash，NVRAM
There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload?（）A、TFTP server, Flash, NVRAMB、ROM, NVRAM, TFTP serverC、NVRAM, TFTP server, ROMD、Flash, TFTP server, ROME、Flash, NVRAM, ROM
A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next？（）A、It checks the configuration registerB、It attempts to boot from a TFTP serverC、It loads the first image file in flash memoryD、It inspects the configuration file in NVRAM for boot instructions
There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload？（）A、Flash，TFTPserver，ROMB、Flash，NVRAM，ROMC、ROM，NVRAM，TFTPserverD、NVRAM，TFTPserver，ROME、TFTPserver，Flash，NVRAM
单选题Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）AThe router will enter setup mode.BThe router will enter ROM monitor mode.CThe router will enter global configuration mode.DThe boot will hang until an IOS is available.
单选题There are no boot system commands in a router configuration in NVRAM.What is the fallback sequencethat router will use to find an ios during reload？（）AFlash，TFTP server，ROMBFlash，NVRAM，ROMCROM，NVRAM，TFTP serverDNVRAM，TFTP server，ROMETFTP server，Flash，NVRAM
单选题There are no boot system commands in arouter configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）AFlash,TFTPserver,ROMBFlash,NVRAM,ROMCROM,NVRAM,TFTP serverDNVRAM,TFTP server,ROMETFTP server,Flash,NVRAM
单选题If NVRAM lacks boot system commands, where does the router look for the Cisco IOS by default?（）AROMBRAMCFlashDBootstrapEStartup-.config
单选题There are no boot system commands in a router configuration in NVRAM.What is the fallback sequence that router will use to find an ios during reload?（）AFlash,TFTP server,ROMBFlash,NVRAM,ROMCROM,NVRAM,TFTP serverDNVRAM,TFTP server,ROMETFTP server,Flash,NVRAM
单选题There are no boot system commands in a router configuration in NVRAM. What is the fallback sequence that the router will use to find an IOS during reload?（）ATFTP server, Flash, NVRAMBROM, NVRAM, TFTP serverCNVRAM, TFTP server, ROMDFlash, TFTP server, ROMEFlash, NVRAM, ROM
单选题There are no boot system commands in a router configuration in NVRAM.What is the fall back sequence that router will use to find an ios during reload？（）AFlash，TFTPserver，ROMBFlash，NVRAM，ROMCROM，NVRAM，TFTPserverDNVRAM，TFTPserver，ROMETFTPserver，Flash，NVRAM
单选题A cisco router is booting and has just completed the POST process.It is now ready to find and load an IOS image.what function does the router perform next?（）AIt checks the configuration registerBIt attempts to boot from a TFTP serverCIt loads the first image file in flash memoryDIt inspects the configuration file in NVRAM for boot instructions
单选题What does a configuration Register Setting of 0x2105 indicate to the Router? （）AThe Boot IOS Code is Located in the NVRAM.BCheck NVRAM for boot system Commands.CBypass NVRAM Configurations.DBoot the IOS Code Located in ROM.EPerform a Password Recovery.FBypass The Code In ROM.