Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? () A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
A. frame-relay arp
B. frame-relay map
C. frame-relay interface-dlci
D. frame-relay lmi-type
相关考题：
在封装了帧中继协议的接口上使能动态逆向地址解析协议的命令是：（ ）A.frame-relay inverse-arpB.frame-realy reverse-arpC.inverse-arpD.reverse-arp
Inverse ARP is being used in the TestKing frame relay network. What is the purpose of Inverse ARP?() A. To ma a known IP address to a MAC addressB. To map a known DLCI to a MAC addressC. To ma a known MAC address to an IP addressD. To ma a known DLCI address to a IP addressE. To ma a known IP address to a SPID addressF. To ma a known SPID address to a MAC address
A new frame－relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?() A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-typeE. frame-relay pvc
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?() A. The Gallant router has the wrong LMI type configuredB. Inverse ARP is providing the wrong PVC information to the Gallant routerC. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD. The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE. The IP address on the serial interface of the Attalla router is configured incorrectly
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame－relay map command shown?() A.The Seria l0/0interface is passing traffic.B.The DLCI 100 was dynamic allyallocated by the routerC.The Seria l0/0 interf aceacquired the IP address of 172.16.3.1 from a DHCP serverD.The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudE.The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
Select the 3 best answers describing operation and configuration of Frame-Relay Inverse ARP.（）A、Dynamic address mapping uses Frame Relay Inverse ARP to request the next-hop protocol address for a specific connection on its known DLCIB、Responses to Inverse ARP requests are entered in an address-to-DLCI mapping table on the router or access server which is used to supply the next-hop protoco address or the DLCI for outgoing trafficC、Inverse ARP is enabled by default for all protocols enabled on the physical interfaceD、Inverse ARP is configured using the following command under the Interface configuration ’frame-relaymap dlci （dlci number） protocol protocol-address’E、Inverse ARP in Frame-Relay is synonymous of ARP in Ethernet
Which statement about Frame Relay is not true？（）A、Static mapping is used when the remote router does not support Inverse ARP.B、Frame Relay Inverse ARP requires LMI capability to construct an address to the DLCI mapping tableon the router.C、Frame Relay Inverse ARP is disabled by default in Cisco IOS Software for all protocols that areenabled on the physical interface.D、Inverse ARP does not work when LMI is disabled.E、Frame Relay provides forward and backward congestion notification messages
A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-typeE、frame-relay pvc
Which of the following statements correctly describes the characteristics of a Frame Relay point-to-point subinterface?（）A、Needs to use Inverse ARP.B、Maps a single IP subnet per DLCI.C、Maps a single IP subnet across multiple DLCIs.D、Resolves NBMA (non broadcast multi access) split horizon issues.E、Requires use of the frame-relay map command.F、None of the above
Inverse ARP is being used in the TestKing frame relay network. What is the purpose of Inverse ARP?（）A、To ma a known IP address to a MAC addressB、To map a known DLCI to a MAC addressC、To ma a known MAC address to an IP addressD、To ma a known DLCI address to a IP addressE、To ma a known IP address to a SPID addressF、To ma a known SPID address to a MAC address
在封装了帧中继协议的接口上使能动态逆向地址解析协议的命令是：（）A、frame-relay inverse-arpB、frame-relay reverse-arpC、inverse-arpD、reverse-arp
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly
Refer to the exhibit. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?（）A、The Serial0/0 interface is passing traffic.B、The DLCI 100 was dynamically allocated by the routerC、The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP serverD、The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudE、The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?（）A、show frame-relay end-to-endB、show frame-relay mapC、show frame-relay lmiD、show frame-relay pvc
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-type
在封装了帧中继协议的接口上使能动态逆向地址解析协议的命令是（）。A、frame-relay inverse-arpB、frame-realy reverse-arpC、inverse-arpD、reverse-arp
which command allows you to verify the encapsulation type CISCO OR IETF for a frame relay link?（）A、show frame-relay mapB、show frame-relay lmiC、show inter serialD、show frame-relay pvc
You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A、The Frame Relay encapsulation on the physical interface.B、The local DLCI on each subinterface.C、An IP address on the physical interface.D、The subinterface type as point-to-point.
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。A、This command should be executed from the global configuration modeB、The IP address 10.121.16.8 is the local router port used to forward dataC、102 is the remote DLCI that will receive the informationD、This command is required for all Frame Relay configurationsE、The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC
单选题Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）Aframe-relay arpBframe-relay mapCframe-relay interface-dlciDframe-relay lmi-type
单选题You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）AThe Frame Relay encapsulation on the physical interface.BThe local DLCI on each subinterface.CAn IP address on the physical interface.DThe subinterface type as point-to-point.
单选题Refer to the exhibit. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?（）AThe Serial0/0 interface is passing traffic.BThe DLCI 100 was dynamically allocated by the routerCThe Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP serverDThe DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudEThe mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
单选题Inverse ARP is being used in the TestKing frame relay network. What is the purpose of Inverse ARP?（）ATo ma a known IP address to a MAC addressBTo map a known DLCI to a MAC addressCTo ma a known MAC address to an IP addressDTo ma a known DLCI address to a IP addressETo ma a known IP address to a SPID addressFTo ma a known SPID address to a MAC address
单选题Which statement about Frame Relay is not true？（）AStatic mapping is used when the remote router does not support Inverse ARP.BFrame Relay Inverse ARP requires LMI capability to construct an address to the DLCI mapping tableon the router.CFrame Relay Inverse ARP is disabled by default in Cisco IOS Software for all protocols that areenabled on the physical interface.DInverse ARP does not work when LMI is disabled.EFrame Relay provides forward and backward congestion notification messages
单选题A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）Aframe-relay arpBframe-relay mapCframe-relay interface-dlciDframe-relay lmi-typeEframe-relay pvc
多选题Which of the following statements correctly describes the characteristics of a Frame Relay point-to-point subinterface?（）ANeeds to use Inverse ARP.BMaps a single IP subnet per DLCI.CMaps a single IP subnet across multiple DLCIs.DResolves NBMA (non broadcast multi access) split horizon issues.ERequires use of the frame-relay map command.FNone of the above
多选题Select the 3 best answers describing operation and configuration of Frame-Relay Inverse ARP.（）ADynamic address mapping uses Frame Relay Inverse ARP to request the next-hop protocol address for a specific connection on its known DLCIBResponses to Inverse ARP requests are entered in an address-to-DLCI mapping table on the router or access server which is used to supply the next-hop protoco address or the DLCI for outgoing trafficCInverse ARP is enabled by default for all protocols enabled on the physical interfaceDInverse ARP is configured using the following command under the Interface configuration ’frame-relaymap dlci （dlci number） protocol protocol-address’EInverse ARP in Frame-Relay is synonymous of ARP in Ethernet