Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（）router ospf 1redistribute ospf 2 external 2 route - map fred!route - map fred permit 10match ip address 1set metric - type type - 1A. No routes are redistributed because a route cannot be both E1 and E2.B. Only OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.C. Inside the OSPF 2 domain, any formerly E2 routes will become E1 routes.D. Routes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（）router ospf 1redistribute ospf 2 external 2 route - map fred!route - map fred permit 10match ip address 1set metric - type type - 1
A. No routes are redistributed because a route cannot be both E1 and E2.
B. Only OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.
C. Inside the OSPF 2 domain, any formerly E2 routes will become E1 routes.
D. Routes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
相关考题：
What type of OSPF router is responsible for redistributing routes into OSPF?() A. ABRB. ASBRC. internal routerD. backbone router
Router R1 sets a route tag for subnet 10.1.1.0／24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?() A. Kilobits/seconDB. Tens of microsecondsC. CostD. Hop countE. No unit is assigneD
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（）route - map fred deny 10match ip address oneroute - map fred deny 20match ip address tworoute - map fred permit 100A. The third route map clause will allow any routes not already filtered by the first two clausesB. R outes permitted by ACL two will be redistributedC. Routes denied by ACL one will be redistributedD. All routes will be filtereD
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）A. the routes originating from the RIP routing domainB. the routes originating from the OSPF stub areaC. all OSPF inter and intra - area routesD. all routes originating from RIP and OSPF routing domains
Refer to the exhibit. AS 65500 is not advertising the prefix 192.168.12.0/22 to its provider. AS 65500 is running OSPF as its IGP. Whi ch of the following additions to the configuration is most likely to solve the problem?（）A. RouterA(config)#ip cefB. RouterA(config)#ip route 192.168.12.0 255.255.255.252 null 0C. RouterA(config - router)#ebgp multihop 1D. RouterA(config - router)#re distribute ospf 1E. RouterA(config - router)#neighbor 192.168.14.253 next - hop - selfF. RouterA(config - router)#neighbor 192.168.14.253 local - as 65500
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Router R1 is configured as shown below:router eigrp 100network 10.0.0.0eigrp stubBased on the information shown above, which two types of routes will be advertised?() A. Receive - onlyB. StubC. StaticD. SummaryE. ConnectedF. Dynamic
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A、R1 will always create and flood a default route into the OSPF domain.B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0A、OSPF works on F0/0 and S0/0/0 without further configurationB、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC、OSPF works with the addition of one command: an router - id command in OSPF router configuration modED、OSPFv3 needs at least two more configuration commands before it works on R1
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
You have just completed an OSPF implementation. While executing your verification plan, you determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem?（）A、DR and BDR election errors between R1 and R2.B、The R2 router has not received the OSPF hello packets from the R1 router.C、Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.D、Mismatched OSPF hello interval configuration between the R1 and R2E、Corrupted LSAs exchanges between the R1 and R2.
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（） route - map fred deny 10 match ip address one route - map fred deny 20 match ip address two route - map fred permit 100A、The third route map clause will allow any routes not already filtered by the first two clausesB、R outes permitted by ACL "two" will be redistributedC、Routes denied by ACL "one" will be redistributedD、All routes will be filtereD
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）A、Receive - onlyB、StubC、StaticD、SummaryE、ConnectedF、Dynamic
单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）AABRBASBRCinternal routerDbackbone router
单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0AOSPF works on F0/0 and S0/0/0 without further configurationBOSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modECOSPF works with the addition of one command: an router - id command in OSPF router configuration modEDOSPFv3 needs at least two more configuration commands before it works on R1
单选题Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）AKilobits/seconDBTens of microsecondsCCostDHop countENo unit is assigneD
多选题For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）AThe router must have one routing protocol configured, but configuration for both routing protocols is not necessaryBThe router must hav e at least one working link connected to each routing domainCThe redistribute command must be configured under EIGRP to send the routes to OSPFDThe redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
单选题Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1ANo routes are redistributed because a route cannot be both E1 and E2.BOnly OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.CInside the OSPF 2 domain, any formerly E2 routes will become E1 routes.DRoutes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
多选题Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）AReceive - onlyBStubCStaticDSummaryEConnectedFDynamic
单选题A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0AThe process id is configured improperlyBThe OSPF area is configured improperlyCThe network wildcard mask is configured improperlyDThe network number is configured improperlyEThe AS is configured improperlyFThe network subnet mask is configuerd improperly
多选题Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?（）ALet the metrics default.BUse each redistributed route's OSPF metric using the redistribute command's metric transparent keywords.CSet the metric using the default - metric router subcommand.DRedistribution is not allowed between two OSPF p rocesses.
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router