Router R1 is configured as shown below:router eigrp 100network 10.0.0.0eigrp stubBased on the information shown above, which two types of routes will be advertised?() A. Receive - onlyB. StubC. StaticD. SummaryE. ConnectedF. Dynamic
Router R1 is configured as shown below:router eigrp 100network 10.0.0.0eigrp stubBased on the information shown above, which two types of routes will be advertised?()
A. Receive - only
B. Stub
C. Static
D. Summary
E. Connected
F. Dynamic
相关考题：
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（）route - map fred deny 10match ip address oneroute - map fred deny 20match ip address tworoute - map fred permit 100A. The third route map clause will allow any routes not already filtered by the first two clausesB. R outes permitted by ACL two will be redistributedC. Routes denied by ACL one will be redistributedD. All routes will be filtereD
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? () A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）A. the routes originating from the RIP routing domainB. the routes originating from the OSPF stub areaC. all OSPF inter and intra - area routesD. all routes originating from RIP and OSPF routing domains
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?() A. The network is stableB. There is a flapping link or interface, and router C knows an alternate path to the networkC. There is a flapping link or interf ace, and router C does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? () A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
The Testking Central and Remote offices are configured as shown below:The remote router can be successfully pinged from the central office but the remote users can‘t access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?（）A. The Frame Relay PVC is down.B. The IP addressing on the Central/Remote serial link is incorrect.C. RIP routing information is not being forwarded.D. Frame Relay inverse-ARP is not properly configured.
Which command will display all the EIGRP feasible successor routes known to a router?() A. Router# show ip eigrp routes *B. Router# show ip eigrp summaryC. Router# show ip eigrp topologyD. Router# show ip eigrp adjacenciesE. Router# show ip eigrp neighbors detail
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet
Which command will display all the EIGRP feasible successor routes known to a router?（）A、Router# show ip eigrp routes *B、Router# show ip eigrp summaryC、Router# show ip eigrp topologyD、Router# show ip eigrp adjacenciesE、Router# show ip eigrp neighbors detail
A router has been configured with an EIGRP variance of 3. Which of the following statements istrue？（）A、An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2B、The successor route will end up in the routing table， and so will any route with a metric at mostthree times greater than the value of the successor’s metricC、EIGRP will only advertise routes that are within three hops of the current routerD、The successor route will end up in the routing table， and so will any route with a metric at leastone third the value of the successor’s metricE、The best three routes with equal cost paths will end up in the routing tableF、The successor route will be any route with three times the value of the advertised distance
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）A、A hub router prevents routes from being advertised to the remote router.B、Only remote routers are configured as stubs.C、Stub routers are not queried for routes.D、Spoke routers connected to hub routers answer the route queries for the stub router.E、A stub router should have only EIGRP hub routers as neighbors.F、EIGRP stub routing should be used on hub routers only.
Router R-1 is configured for BGP routing as shown below： router bgp 65300network 27.0.0.0neighbor 192.23.1.1 remote-as 65300 From the perspective of router R-1， what kind of router is the router with IP address 192.23.1.1？（）A、A peer router running IBGPB、A peer router running EBGPC、A community member running IBGPD、A peer group member running IBGPE、A peer group member running EBGP
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（） route - map fred deny 10 match ip address one route - map fred deny 20 match ip address two route - map fred permit 100A、The third route map clause will allow any routes not already filtered by the first two clausesB、R outes permitted by ACL "two" will be redistributedC、Routes denied by ACL "one" will be redistributedD、All routes will be filtereD
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）A、Receive - onlyB、StubC、StaticD、SummaryE、ConnectedF、Dynamic
单选题Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（） route - map fred deny 10 match ip address one route - map fred deny 20 match ip address two route - map fred permit 100AThe third route map clause will allow any routes not already filtered by the first two clausesBR outes permitted by ACL two will be redistributedCRoutes denied by ACL one will be redistributedDAll routes will be filtereD
多选题For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）AThe router must have one routing protocol configured, but configuration for both routing protocols is not necessaryBThe router must hav e at least one working link connected to each routing domainCThe redistribute command must be configured under EIGRP to send the routes to OSPFDThe redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
多选题Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）AReceive - onlyBStubCStaticDSummaryEConnectedFDynamic
单选题A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0AThe process id is configured improperlyBThe OSPF area is configured improperlyCThe network wildcard mask is configured improperlyDThe network number is configured improperlyEThe AS is configured improperlyFThe network subnet mask is configuerd improperly
多选题What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）AA hub router prevents routes from being advertised to the remote router.BOnly remote routers are configured as stubs.CStub routers are not queried for routes.DSpoke routers connected to hub routers answer the route queries for the stub router.EA stub router should have only EIGRP hub routers as neighbors.FEIGRP stub routing should be used on hub routers only.
单选题Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）ASubnet numberBNext - hop router IP address of the routeCWhether the route is an E1 or E2 routeDThe ro ute's tagEThe number of router hops between the router and the subnet