Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）A、Receive - onlyB、StubC、StaticD、SummaryE、ConnectedF、Dynamic
Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
- A、Receive - only
- B、Stub
- C、Static
- D、Summary
- E、Connected
- F、Dynamic
相关考题：
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1 show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best 1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, bestA. R1 has a neighbor 1.1.1.1 command configured.B. R1 has a neighbor 2.2.2.2 command configured.C. The show ip bgp command lists a line for 190.1.0.0/16 with both an and an i on the left.D. R1 is in ASN 1.
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Based on the show ip route isis output on R1, which statement is true? () A. The i su 10.1.0.0/23 route is a suppressed route.B. The i su 10.1. 0.0/23 route is a summary route.C. The i su 10.1.0.0/23 route is an IS - IS external route.D. The R1 IS - IS router is an ASBR.E. The R1 IS - IS router is an ABR that belongs to multiple IS - IS areas.F. The R1 IS - IS router is performing route aggregation and is suppressing the more specific 10.1.0.0/23 prefix.
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. EIGRP is configured on all routers in the network. On a basis of the show ip eigrp topology output provided, what conclusion can be deri ved? () A.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24B.Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0C.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachableD.Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent out about network 10 .6.1.0/24
Based on the exhibited output, which three statements are true?() A. The route to 10.2.0.0/16 was redistributed into EIGRP.B. A default route has been redistributed into the EIGRP autonomous system.C. R1 is configured with the ip summary - address command.D. R1 is sourcing a n external EIGRP route from Null0.E. The router at 10.1.1.2 is configured with the ip default - network 0.0.0.0 command.F. R1 is configured with the variance command.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）A. The OSPF area is not configured properly.B. The priority on R1 should be set higher.C. The cost on R1 should be set higher.D. The hello and dead timers are not configured properly.E. A backup designated router needs to be added to the network.F. The OSPF process ID numbers must match.
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes. Which commands will accomplish these options?（）A、show hostsB、show sessionsC、show connectionsD、disconnectE、CTRL+SHIFT+6xF、exit
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
In which Cisco IOS configuration mode is the route distinguisher （RD） configured？（）A、R1（config-route-at）#B、R1（config-route-map）#C、R1（config-it）#D、R1（config-vrf）#E、R1（config）#F、R1（router）#
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A、show ip routeB、show ip eigrp topologyC、show ip ospf topologyD、show ip eigrp topology 10.1.1.0/24
A network administrator has configured access list 172 to prevent Telnet and ICMP traffic from reaching a server with the address if 192.168.13.26. Which command can the administrator issue to verify that the access list is working properly?（）A、Router# ping 192.168.13.26B、Router# debug access-list 172C、Router# show open ports 192.168.13.26D、Router# show access-listE、Router# show ip interface
Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3A、R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.B、The ping 4.4.4.4 command on R1 must currently be successful.C、R1's Fa0/0 OSPF cost is 3.D、4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）A、 InitB、 IdleC、 ActiveD、 StandbyE、 EstablishedF、 Backup
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
what is the cause of this problem?（）A、The OSPF area is not configured properly.B、The priority on R1 should be set higher.C、The cost on R1 should be set higher.D、The hello and dead timers are not configured properly.E、A backup designated router needs to be added to the network.F、The OSPF process ID numbers must match.
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（） R1# show ip bgp 190.1.0.0/16 BGP routing table entry for 190.1.0.0/16, version 121 Paths: (1 available, best #1, table Default - IP - Routing - Table) Advertised to update - groups: 1 1 2 3 4 1.1.1.1 from 2.2.2.2 (3.3.3.3) Origin IGP, metric 0, localpref 100, valid, internal, bestA、R1 has a neighbor 1.1.1.1 command configured.B、R1 has a neighbor 2.2.2.2 command configured.C、The show ip bgp command lists a line for 190.1.0.0/16 with both a n and an i on the left.D、R1 is in ASN 1.
Which command would display OSPF parameters such as filters， default metric， maximum paths，and number of areas configured on a router？（）A、show ip protocolB、show ip routeC、show ip ospf interfaceD、show ip ospfE、show ip interfaceF、None of the other alternatives apply
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
单选题Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3AR1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command.BThe ping 4.4.4.4 command on R1 must currently be successful.CR1's Fa0/0 OSPF cost is 3.D4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.
多选题Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）AReceive - onlyBStubCStaticDSummaryEConnectedFDynamic
单选题How can you verify that you have correctly configured SSH access to your Junos device?（）Auser@router# show system servicesBuser@router show configuration servicesCuser@router# show configuration system servicesDuser@router# show system login
单选题Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）AR1 has been configured with an ip default- network 2.0.0.0 command.BR1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.CR1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.DAnother router has been configured with an ip default - network 2.0.0.0 command.EAnother router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
多选题Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）AInitBIdleCActiveDStandbyEEstablishedFBackup