Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? () A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? ()
A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
相关考题：
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B
Refer to the exhibit. EIGRP has been configured on al l routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A?（）A. R 4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network AB. R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected a s the advertised distance from R2 is higher than the feasible distanceC. R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network AD. R2 becomes the successor and will be placed in the routing t able. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）A. the routes originating from the RIP routing domainB. the routes originating from the OSPF stub areaC. all OSPF inter and intra - area routesD. all routes originating from RIP and OSPF routing domains
Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing ta ble. You are also not able to see the R4 Ethernet subnet on the R1 routing table.Which configuration change should be made to resolve this issue? Select the routers where the configuration change will be required, and select the required EIGRP configur ation command(s).（）A. R1 and R4B. R2 and R3C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary - address eigrp 110.2.2.0 255.255.255.0D. variance 2E. eigrp stub connectedF. no auto - summary
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）A. The redistribution command should be reentered with the match route - type parameter included.B. The redistribution command should be reentered wit h the route - map map - tag parameter included.C. The redistribution command should be reentered with the metric metric - value parameter included.D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?() A. Interface authentication must be configuredB. The routing processes must be configured with an area IDC. IP unicast routing must be enabledD. IPv4 ad dresses must be applied to the interfaces
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?() A. DHCP requests from the host will be rebroadcasted to R2.B. To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.C. To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.D. R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.E. R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
Refer to the exhibit. On the basis of the output, what two conclusions can be reached?() A. The default administrative distance has been changed.B. IS - IS is not enabled.C. Three physical interfaces are taking part in integrated IS - IS.D. IS - IS is not redistributing any oth er routing protocols.E. There are two neighboring routers sending IS - IS routing information.F. Address summarization is configured.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. IP multicast configuration changes have been made on several routers.However, the IP multicast table displayed in the exhibit still does not reflect the changes. What should be done to display the new routing table information? （）A. Issue the clear ip route * privileged EXEC command.B. Issue the clear ip igmp group privileged EXEC command.C. Issue the no ip mroute - cache privileged EXEC command.D. Issue the clear ip mroute privileged EXEC command.
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）A. The ip ospf network broadcast command should be configured on each Frame Relay interfaceB. The ip ospf network non -broadcast command should be configured on each Frame Relay interfaceC. Th e ip ospf priority value on the spoke routers should be set to 0D. The ip ospf priority value on the hub router should be set to 0E. The neighbor command should be configured under the OSPF routing process on all routers
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? () A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?（）A. 10.0.0.0/8B. 172.16.10.0/24C. 172.16.0.0/24D. 10.10.10.0/24E. 172.16.0.0/16F. 10.10.0.0/16
Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192／26 network to a host on the LAN attached to router R1?() A.The path of the packets will be R3 to R2 to R1.B.The path of the packets will be R3 to R1 to R2.C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.D.The path of the packets will be R3 to R1
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?（）A.Configure the no ip subnet-zero command on R1, R2, and R3.B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）A、R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1B、R1 can send IP packets to R2, but R2 cannot send IP packets to R1C、R2 no longer learns EIGRP routes from R1 for routes not connected to R1D、R1 no longer replies to R2's Query messagesE、R2n o longer sends to R1 Query messages
Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A、Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B、R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C、R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D、All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
Refer to the exhibit. Which statement is correct based on the show login command output shown？（）A、When the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.B、The login block-for command is configured to block login hosts for 93 seconds.C、All logins from any sources are blocked for another 193 seconds.D、Three or more login requests have failed within the last 100 seconds.
多选题Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）AAll of the routers need to be configured for backbone Area 1.BR1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.CA static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.DThe hello and dead interval timers are not set to the same values on R1 and R3.EEIGRP is also configured on these routers with a lower administrative distance.FR1 and R3 are configured in different areas.
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A physical layer issuesB no spanning tree loopsC use of non-default HSRP timersD failure to set the command standby 35 preempt
多选题Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）AR1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1BR1 can send IP packets to R2, but R2 cannot send IP packets to R1CR2 no longer learns EIGRP routes from R1 for routes not connected to R1DR1 no longer replies to R2's Query messagesER2n o longer sends to R1 Query messages