S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?（）A.Configure the no ip subnet-zero command on R1, R2, and R3.B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?（）
A.Configure the no ip subnet-zero command on R1, R2, and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
相关考题：
● 要进入以太端口配置模式，下面的路由器中命令，哪一条是正确的？（57）（57）A. R1 (config)# interface e0B. R1 interface e0C. R1 line e0D. R1 (config)# line s0
下表是该系统中路由器的IP地址分配表。请根据上图完成以下R3路由器的配置：R3(config)interface e0/1(进入接口e0/1配置模式)R3(coafig-if) ip address 202.115.13.254(4)(设置IP地址和掩码)R3(config) interface s0/0(进入串口配置模式)R3(config-if) ip address(5)255.255.255.0(设置IP地址和掩码)R3(config) interface s0/1R3(config-if)ip address(6)255.255.255.0R3(config) interface s0/2R3(eonfig-if)ip address(7)255.255.255.0R3(config) interface s0/3R3(eonfig-if)ip address(8)255.255.255.0R3(config) interface s0/4R3(config-if)ip address(9)255.255.255.0R3(config) interface s0/5R3(config-if) ip address(10)255.255.255.0
已知R0＝0x10,R1＝0x20,R2=0x08,R3=0xFFFFFFF3,则指令LSL R0,R0,R2执行后，R0＝___【13】___，指令MVN R1,R3执行后R1＝___【14】___。
阅读以下说明，回答问题1和问题2，将解答填入答题纸对应的解答栏内。 【说明】 某公司有3个分支机构，网络拓扑结构及地址分配如图4-1所示。【问题1】（每空1分，共11分） 公司申请到202.111.1.0/29的公有地址段，采用NAPT技术实现公司内部访问互联网的要求，其中，192.168.16.0/22网段禁止访问互联网。 R1、R2和R3的基本配置已正确配置完成，其中R1的配置如下。请根据拓扑结构，完成下列配置代码。 R1的基本配置及NAPT配置如下： R1enable Rlconfig tenrunal R1(config)interface fastenthemet 0/0 R1(config-if)ip address 192.168.0.1 255.255.255.252 R1(config-if)no shutdown Rl(config-if)exit R1(config)interface fastenthemet 0/1 R1(config-if)ip address 192.168.0.9 255.255.255.252 R1(config-if)no shutdown R1(config-if)exit R1(config)interface fastenthernet 0/2 R1(config-if)ip address （1） 255.255.252.0 //使用网段中最后一个地址 R1(config-if)no shutdown R1(config-if)exit R1(config)interface serial 0 R1(config-if)ip address 202.111.1.1 255.255.255.248 R1(config-if)no shutdown R1(corffig)ip nat pool ss 202.111.1.1 （2） netmask （3） R1(corffig) interface （4） fastenthernet 0/0-1 R1(config-if)ip nat （5） R1(config-if)interface serial 0 Rl(config-if)ip nat （6） R1(config-if)exit R1(config)access-Iist l permit 192.168.0.0 （7） Rl(config)ip nat inside （8） list （9） pool （10） （11） 【问题2】．（每空2分，共4分） 在R1、R2和R3之间运行OSPF路由协议，其中R1、R2和R3的配置如下。 行号 配置代码 1 R1(config)router ospf 1 2 R1(config-router)network 192.168.4.0 0.0.3.255 area 0 3 Rl(config-router)network 192.168.0.0 0.0.0.3 area 0 4 Rl(config-router)network 192.168.0.8 0.0.0.3 area 0 5 R2enable 6 R2config terminal 7 R2(config)router ospf 2 8 R2(config-router)netvrork 192.168.8.0 0.0.3.255 area 0 9 R2 (config-router)network 192.168.12.0 0.0.3.255 area 0 1 0 R2 (config-router)network 192.168.0.4 00.0.3 area 0 1 1 R3enable 1 2 R3config terminal 1 3 R3(config)router ospf 3 1 4 R3(config-router)netvrork 192168.0.8 00.0.3 area 0 1 5 R3(config-router)network 192.168.0.4 0.0.0.3 area 0 1．配置完成后，在R1和R2上均无法ping通R3的局域网，可能的原因是（12）。 （12）备选答案： A．在R3上未宣告局域网路由 B．以上配置中第7行和第13行配置错误 C．第1行配置错误 D．R1、R2未宣告直连路由． 2．在OSPF中重分布默认路由的命令是：（13）。 （13）备选答案： A．Rldefault-informaton originate B．R1(config-if)default-information originate C．R1(config-router)default-information originate D．Rl(config)default-information originate
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?() A. DHCP requests from the host will be rebroadcasted to R2.B. To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.C. To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.D. R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.E. R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? () A.S1(config)# interface fastethernet 0/1S1(config - if)# ip helper - address 10.0.0.2B.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1C.R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1D.R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1E.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192／26 network to a host on the LAN attached to router R1?() A.The path of the packets will be R3 to R2 to R1.B.The path of the packets will be R3 to R1 to R2.C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.D.The path of the packets will be R3 to R1
R1(AS1)－－－－－－R2(AS2)－－－－－R3(AS2)－－－－R4(AS2),R1在AS1,R2,R3,R4在AS2,R1和R2建EBGP,R2和R3IBGP,R3和R4IBGP,产生BGP路由从R1传给R2,问这条路有会不会在R4上出现,如果不会,怎么解决.
要进入以太网端口配置模式，下面的路由器命令中，哪一条是正确的？ （ ） 。A.[R1] interface e0B. interface e0C.[R1] line e0D. line s0
Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）A、R1 limi ts EIGRP to around 250Kbps on DLCI 102B、R1 limits EIGRP to around 250Kbps on DLCI 104C、R1 limits EIGRP to around 150Kbps on every DLCID、R1 does not limit EIGRP because noWAN bandwidth control has been configured
r1 is the hub ， multipoint mode subinterface， r2 and r3 is spoke， when r2 down at the spoke， What will r1 react？how about r3？
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B、S0/2 may currently be in a state other than up/up.C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D、S0/2 may be configured as a passive inter face.
Examine the following configuration on Router R1. R1's show ip route 172.16.4.1 command list s a route with outgoing interface S0/1/1. Host 172.16.3.3 uses telnet to connect to host 172.16.4.1.What will Router R1 do with the packets generated by host 172.16.3.3 because of the telnet,assuming the packets enter R1's F0/0 interface?（） interface Fastethernet 0/0 ip address 172.16.1.1 255.255.255.0 ip policy route - map Q2 ! route - map Q2 permit match ip address 101 set interface s0/0/1 ! access - list 101 permit tcp host 172.16.3.3 172.16.4.0 0.0.0.255A、The packet will be forwarded out S0/0 /1, or not at all.B、The packet will be forwarded out S0/0/1 if it is up.C、The packet will be forwarded out S0/1/1 if it is up.D、The packet will be forwarded out S0/1/1 if it is up, or if it is not up, out s0/0/1.E、The packet will be forwarded o ut S0/0/1 if it is up, or if it is not up, out s0/1/1.
对由三层平壁组成的多层平壁稳定热传导而言，若三层的传热推动力△t1＞△t2＞△t3，则三层平壁的传热阻力R1，R2，R3之间的关系是（）。 A、R1＞R2＞R3B、R1＜R2＜R3C、R1＞R3＞R2D、R2＞R1＞R3
多选题Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）AAll of the routers need to be configured for backbone Area 1.BR1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.CA static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.DThe hello and dead interval timers are not set to the same values on R1 and R3.EEIGRP is also configured on these routers with a lower administrative distance.FR1 and R3 are configured in different areas.
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A physical layer issuesB no spanning tree loopsC use of non-default HSRP timersD failure to set the command standby 35 preempt
单选题R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1（）。AThe frame does not have MAC addresses.BThe source MAC address in the frame is the MAC address of the NIC of Host 1.CThe source MAC address in the frame is the MAC address of the s0/0/0 interface of R1.DThe destination MAC address in the frame is the MAC address of the NICof server 1.EThe destination MAC address in the frame is the MAC address of the s0/0/0 interface of R2
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）Aphysical layer issuesBno spanning tree loopsCuse of non-default HSRP timersDfailure to set the command standby 35 preempt
问答题r1 is the hub ， multipoint mode subinterface， r2 and r3 is spoke， when r2 down at the spoke， What will r1 react？how about r3？
单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enableARIPng will be enabled on no interfaces.BRIPng will be enabled on one interface.CRIPng will be enabled on two interfaces.DRIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.