A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?() A. The switch port link lights will be off on both switches indicating the ports are not connected.B. The switch port link light will be off on one switch indicating that STP has disabled the port.C. The switch port link lights will flash amber indicating an error.D. The switch port link lights will be green indicating normal operation.
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?()
A. The switch port link lights will be off on both switches indicating the ports are not connected.
B. The switch port link light will be off on one switch indicating that STP has disabled the port.
C. The switch port link lights will flash amber indicating an error.
D. The switch port link lights will be green indicating normal operation.
相关考题：
The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?() A.StraightB.ConsoleC.CrossoverD.Loopback
After connecting a PC to an available port on a switch, you find that the PC can not access any of the resources on the LAN. No other PC's connected to the switch appear to be having any issues. What is the most likely cause for this problem?A．The router lacks a routing table entry for the new hostB．The host switch port is assigned to the incorrect VLANC．The host MAC address is incorrectly configuredD．A STP instance for the new host has not been initializedE．The switch does not have the MAC address hard coded in the CAM table.
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?() A. Switch(config-if)# vlan allB. Switch(config-if)# switchport trunk encapsulation dot1qC. Switch(config-if)# switchport access vlan allD. Switch(config-if)# switchport mode trunkE. Switch(config-if)# switchport access vlan 303
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0／10 is not the root port for VLAN 2?() A.This switch has more than one interface connected to the root network segment in VLAN 2.B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.C.This switch interface has a higher path cost to the root bridge than another in the topology.D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?（）A、StraightB、ConsoleC、CrossoverD、Loopback
When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network,how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port?（）A、by snooping the CoS marking on the incoming framesB、by using RTP hello messages between the switch port and the Cisco IP PhoneC、by using CDPD、by using DHCP snoopingE、by snooping the incoming 802.1Q VLAN tag
A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails. What is the problem with the switch？（）A、The power supply has inadequate wattage.B、Power is incorrectly configured on the port.C、It does not support 802.3af Poe.D、Power is not enabled on the port.
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A、The switch port link lights will be off on both switches indicating the ports are not connected.B、The switch port link light will be off on one switch indicating that STP has disabled the port.C、The switch port link lights will flash amber indicating an error.D、The switch port link lights will be green indicating normal operation.
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）A、Switch(config-if)# vlan allB、Switch(config-if)# switchport trunk encapsulation dot1qC、Switch(config-if)# switchport access vlan allD、Switch(config-if)# switchport mode trunkE、Switch(config-if)# switchport access vlan 303
You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function normally， and the new workstation obtains an address when manually forced to renew its address. What should be configured on the switch to allow the workstation to obtain an IP address at boot？（）A、UplinkFast on the switch port connected to the serverB、BackboneFast on the switch port connected to the serverC、PortFast on the switch port connected to the workstationD、trunking on the switch
A cisco aironet 1020 controller-based access point has been connected to a catalyst 3550-24 pwr switch. however， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）A、The switch must be configured with an IP address,subnet mask,and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch port.F、The switch must be fully configured as an SNMP agent.
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）A、The switch must be configured with an IP address, subnet mask, and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch
Which statement is correct about RSTP port roles？（）A、The designated port is the switch port on every nonroot bridge that is the chosen path to theroot bridge. There can be only one designated port on every switch. The designated portassumes the forwarding state in a stable active topology. All switches connected to a given segment listen to all BPDUs and determine the switch that will be the root switch for a particular segment.B、The disabled port is an additional switch port on the designated switch with a redundant link to the segment for which the switch is designated. A disabled port has a higher port ID than the disabled port on the designated switch. The disabled port assumes the discarding state in astable active topology.C、The backup port is a switch port that offers an alternate path toward the root bridge. The backup port assumes a discarding state in a stable， active topology. The backup port will be present on nondesignated switches and will make a transition to a designated port if the current designated path fails.D、The root port is the switch port on every nonroot bridge that is the chosen path to the root bridge. There can be only one root port on every switch. The root port assumes the forwarding state in a stable active topology.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR Switch. However， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller
When configuring port security on a Cisco Catalyst switch port， what is the default action taken by the switch if a violation occurs？ （）A、protect （drop packets with unknown source addresses）B、restrict （increment SecurityViolation counter）C、shut down （access or trunk port）D、transition （the access port to a trunking port）
单选题A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）AThe switch port link lights will be off on both switches indicating the ports are not connected.BThe switch port link light will be off on one switch indicating that STP has disabled the port.CThe switch port link lights will flash amber indicating an error.DThe switch port link lights will be green indicating normal operation.
单选题Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。Aa switch with a trunk link that is configured between the switchesBa router with an IP address on the physical interface that is connected to the switchCa switch with an access link that is configured between the switchesDa router with subinterfaces configured on the physical interface that is connected to the switch
单选题An administrator has an existing HMC and POWER6 570 connected to a network switch. The administrator is planning to install two POWER6 570s with a dedicated HMC. Which infrastructure is required for the new HMC？（）AAn additional switch for the new HMc BAsynchronous adapters on the new HMcCThe two 570 servers are directly connected to the new HMc DOne 570 is directly connected to the new HMC and the other is directly connected to the existing HMc
单选题A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails. What is the problem with the switch？（）AThe power supply has inadequate wattage.BPower is incorrectly configured on the port.CIt does not support 802.3af Poe.DPower is not enabled on the port.
单选题When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network, how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port? （）Aby snooping the CoS marking on the incoming framesBby using RTP hello messages between the switch port and the Cisco IP PhoneCby using CDPDby using DHCP snoopingEby snooping the incoming 802.1Q VLAN tag
单选题An administrator has an existing HMC and POWER6 570 connected to a network switch. The administrator is planning to install two POWER6 570s with a dedicated HMC. Which infrastructure is required for the new HMC?（）AAn additional switch for the new HMCBAsynchronous adapters on the new HMCCThe two 570 servers are directly connected to the new HMCDOne 570 is directly connected to the new HMC and the other is directly connected to the existing HMC
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）AThe switch must be configured with an IP address,subnet mask,and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch port.FThe switch must be fully configured as an SNMP agent.
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）AThe switch must be configured with an IP address, subnet mask, and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch