单选题When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network, how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port? （）Aby snooping the CoS marking on the incoming framesBby using RTP hello messages between the switch port and the Cisco IP PhoneCby using CDPDby using DHCP snoopingEby snooping the incoming 802.1Q VLAN tag
单选题
When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network, how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port? （）
A
by snooping the CoS marking on the incoming frames
B
by using RTP hello messages between the switch port and the Cisco IP Phone
C
by using CDP
D
by using DHCP snooping
E
by snooping the incoming 802.1Q VLAN tag
参考解析
解析：
暂无解析
相关考题：
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A. using DHCP snoopingB. snooping the incoming 802.1Q VLAN tagC. using CDPD. snooping the CoS marking on the incoming frames
Which three route filtering statements are true?() A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Which two Cisco AutoQoS configuration statements are true？ （）A、the auto discovery qos command is supported on serial interfaces， subinterfaces， and virtual interfacesB、CEF must be enabled before configuring the auto discovery qos commandC、the auto discovery qos privilege EXEC command must be configured on a router for several days to collect a sampling of data trafficD、the auto qos trust command relies on NBAR to provide VoIP classificationE、the auto qos voip command configures the voip classification on routers and switches
Which two statements or sets of statements are true about the application of the qos pre-classify command？（）A、 If the classification policy is based upon the ToS byte， the qos pre-classify command is required because the ToS byte only appears in the inner IP header.B、 The ToS byte is copied to the outer header by default. Therefore， the qos pre-classify command is not necessary.C、 With GRE encapsulation， the qos pre-classify command is applied on the tunnel interface. This practice allows for different OoS configurations on each tunnel.D、 With GRE encapsulation， the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.E、 With IPsec encapsulation， the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.
When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network,how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port?（）A、by snooping the CoS marking on the incoming framesB、by using RTP hello messages between the switch port and the Cisco IP PhoneC、by using CDPD、by using DHCP snoopingE、by snooping the incoming 802.1Q VLAN tag
When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）A、Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.B、Enter the no switchport command to disable Layer 2 functionality at the interface level.C、Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.D、Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
What does the mac packet-classify command do when applied to an interface configuration？（）A、 It enables MAC ACLs to be applied to only IP packets that enter the interface.B、 It enables MAC ACLs to be applied to only non-IP packets that enter the interface.C、 It enables MAC ACLs to be applied to all packets that enter the interface.D、 It enables MAC ACLs to be used for QoS settings.
Which configuration command dynamically detects and configures a PPPoA interface?（）A、auto-configure ipB、auto-configure pppC、auto-configure pppoeD、auto-configure bridgedethernet
Which configuration command dynamically detects and configures a Bridged 1483 interface?（）A、auto-configure ipB、auto-configure pppC、auto-configure pppoeD、auto-configure bridgedethernet
You are an administrator of a network that uses PPP for CHAP authentication over ever WAN link. What command would you enter to display the CHAP authentication as it occurs in real time?（）A、show ppp authenticationB、debug PAP authenticationC、debug PPP authenticationD、show interface serial0E、show CHAP authentication
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A、using DHCP snoopingB、snooping the incoming 802.1Q VLAN tagC、using CDPD、snooping the CoS marking on the incoming frames
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）A、show ip access-listB、show access-listC、list ip interfaceD、show interfaceE、show ip interface
What accurately describes the usage of a Cisco AutoQoS command？（）A、on Catalyst switches， the show auto discovery qos command is used to display the data collected during the Auto-Discovery phaseB、on Catalyst switches， the show auto qos command is used to display packet statistics of all classes that are configured for all service policiesC、on Cisco routers， the show mls qos maps command is used to verify the CoS-to-DSCP maps for egress packet queuingD、on Cisco routers， the show auto qos command is used to display the AutoQoS interface templates， policy maps， class maps， and ACLs
Which command will allow you to display the configured QoS group and the ingress buffer allocated to each QoS group？（）A、 show interface priority-flow-controlB、 show interface queuingC、 show queuing interfaceD、 show policy-map system type queuingE、 show policy-map interface ethernet type queuing
Your database is running in the ARCHIVELOG mode. You have configured RMAN for backup and recovery operations. You execute the following command from the RMAN prompt： RMAN CONFIGURE CONTROLFILE AUTOBACKUP ON； After executing this command， in which of the following cases will RMAN make an auto-backup of the control file？ （）A、 when you change the name of a datafileB、 when you drop a table from the databaseC、 when you take an export of the databaseD、 when you back up the database using OS utilitiesE、 when you issue an ALTER SYSTEM SWITCH LOGFILE statementF、 when you issue a BACKUP command from inside the RMAN run block
You install Windows Server 2008 R2 （Server Core I nstallation） on a server. You install the Hyper-V role and Windows PowerShell 2.0 on the server. When you attempt to run an iscsicli command， the command fails. You need to be able to immediately run the iscsicli command successfully. What should you do？（）A、Run the ocsetup MultiPathIo command.B、Run the sc config msiscsi start= auto command.C、Run the start-service msiscsi PowerShell cmdlet.D、Run the set-service msiscsi CstartupType auto PowerShell cmdlet.
多选题Which two Cisco AutoQoS configuration statements are true？ （）Athe auto discovery qos command is supported on serial interfaces， subinterfaces， and virtual interfacesBCEF must be enabled before configuring the auto discovery qos commandCthe auto discovery qos privilege EXEC command must be configured on a router for several days to collect a sampling of data trafficDthe auto qos trust command relies on NBAR to provide VoIP classificationEthe auto qos voip command configures the voip classification on routers and switches
多选题Which two statements are true about the various methods of implementing QoS？（）ACisco AutoQoS can be used repeatedly to apply a single QoS policy to multiple interfaces.BCisco AutoQoS includes an optional web-based GUI for automating the configuration of QoS services.CCisco AutoQoS provides capabilities to automate VoIP deployments.DThe auto qos global configuration command is used to configure Cisco AutoQoS.EThe Modular QoS CLI （MQC） is the best way to fine tune QoS configurations.FThe SDM QoS wizard is the fastest way to implement QoS.
多选题The Cisco AutoQoS feature is being used throughout the Company VOIP network. Which three statements about this feature are true？（）AThe mls qos global configuration command must be entered before configuring AutoQoS.BCEF must be enabled.CThe no auto qos voip command is used to disable Cisco AutoQos and revoke all configurations generated by Cisco AutoQos.DCDP must be enabled.ESNMP must be enabled.
多选题Which two statements or sets of statements are true about the application of the qos pre-classify command？（）AIf the classification policy is based upon the ToS byte， the qos pre-classify command is required because the ToS byte only appears in the inner IP header.BThe ToS byte is copied to the outer header by default. Therefore， the qos pre-classify command is not necessary.CWith GRE encapsulation， the qos pre-classify command is applied on the tunnel interface. This practice allows for different OoS configurations on each tunnel.DWith GRE encapsulation， the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.EWith IPsec encapsulation， the qos pre-classify command is applied on the physical interface. This practice allows for different OoS configurations on each interface.
多选题You need to configure a new Cisco router to be installed in the Company VOIP network. Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached？ （）Aswitchport voice vlan vlan-idBmls qos trust device cisco-phoneCswitchport priority extend cos_valueDmls qos trust cosEmls qos trust override cos
单选题When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）Ashow ip access-listBshow access-listClist ip interfaceDshow interfaceEshow ip interface
单选题Which command will allow you to display the configured QoS group and the ingress buffer allocated to each QoS group？（）A show interface priority-flow-controlB show interface queuingC show queuing interfaceD show policy-map system type queuingE show policy-map interface ethernet type queuing
单选题What accurately describes the usage of a Cisco AutoQoS command？（）Aon Catalyst switches， the show auto discovery qos command is used to display the data collected during the Auto-Discovery phaseBon Catalyst switches， the show auto qos command is used to display packet statistics of all classes that are configured for all service policiesCon Cisco routers， the show mls qos maps command is used to verify the CoS-to-DSCP maps for egress packet queuingDon Cisco routers， the show auto qos command is used to display the AutoQoS interface templates， policy maps， class maps， and ACLs
单选题What does the mac packet-classify command do when applied to an interface configuration？（）A It enables MAC ACLs to be applied to only IP packets that enter the interface.B It enables MAC ACLs to be applied to only non-IP packets that enter the interface.C It enables MAC ACLs to be applied to all packets that enter the interface.D It enables MAC ACLs to be used for QoS settings.