单选题Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）ASubnet numberBNext - hop router IP address of the routeCWhether the route is an E1 or E2 routeDThe ro ute's tagEThe number of router hops between the router and the subnet
单选题
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）
A
Subnet number
B
Next - hop router IP address of the route
C
Whether the route is an E1 or E2 route
D
The ro ute's tag
E
The number of router hops between the router and the subnet
参考解析
解析：
暂无解析
相关考题：
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Based on the exhibited output, which three statements are true?() A. The route to 10.2.0.0/16 was redistributed into EIGRP.B. A default route has been redistributed into the EIGRP autonomous system.C. R1 is configured with the ip summary - address command.D. R1 is sourcing a n external EIGRP route from Null0.E. The router at 10.1.1.2 is configured with the ip default - network 0.0.0.0 command.F. R1 is configured with the variance command.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A、R1 will always create and flood a default route into the OSPF domain.B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0A、OSPF works on F0/0 and S0/0/0 without further configurationB、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC、OSPF works with the addition of one command: an router - id command in OSPF router configuration modED、OSPFv3 needs at least two more configuration commands before it works on R1
Enterprise Router R1 connects an Enterprise to the Internet. R1 needs to create and advertise a default route into the Enterprise using EIGRP. The engineer creating the implementation plan has chosen to base this default route on the ip route command, rather than using i p default - network. Which of the following is not a useful step with this style of default route configuration?（）A、Create the default route on R1 using the ip route 0.0.0.0 0.0.0.0 outgoinginterface command.B、Redistribute the statically configured defa ult route.C、Disable auto - summary.D、Configure the network 0.0.0.0 command.E、Ensure R1 has no manually configured summary routes using the ip summary- address eigrp command.
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
what is the cause of this problem?（）A、The OSPF area is not configured properly.B、The priority on R1 should be set higher.C、The cost on R1 should be set higher.D、The hello and dead timers are not configured properly.E、A backup designated router needs to be added to the network.F、The OSPF process ID numbers must match.
You have just completed an OSPF implementation. While executing your verification plan, you determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem?（）A、DR and BDR election errors between R1 and R2.B、The R2 router has not received the OSPF hello packets from the R1 router.C、Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.D、Mismatched OSPF hello interval configuration between the R1 and R2E、Corrupted LSAs exchanges between the R1 and R2.
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
多选题Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?（）AAll of the routers need to be configured for backbone Area 1.BR1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.CA static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.DThe hello and dead interval timers are not set to the same values on R1 and R3.EEIGRP is also configured on these routers with a lower administrative distance.FR1 and R3 are configured in different areas.
单选题An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）AEnsure that an interface has been configured with an IP addressBEnsure that IP classless is enabledCEnsure that the interfaces can ping their directly connected neighborsDEnsure that an interface has been configured with an IP address and is up
单选题Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）AR1 will always create and flood a default route into the OSPF domain.BR1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.CR1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.DR1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
多选题For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）AThe router must have one routing protocol configured, but configuration for both routing protocols is not necessaryBThe router must hav e at least one working link connected to each routing domainCThe redistribute command must be configured under EIGRP to send the routes to OSPFDThe redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
单选题Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）AR1 has been configured with an ip default- network 2.0.0.0 command.BR1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.CR1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.DAnother router has been configured with an ip default - network 2.0.0.0 command.EAnother router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
单选题Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）AR1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.BFor any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.CFor any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.DNo subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.