Why would a network administrator configure port security on a switch?() A. To prevent unauthorized Telnet access to a switch port.B. To limit the number of Layer 2 broadcasts on a particular switch port.C. To prevent unauthorized hosts from accessing the LAN.D. To protect the IP and MAC address of the switch and associated ports.E. To block unauthorized access to the switch management interfaces over common TCP ports.

Why would a network administrator configure port security on a switch?()

A. To prevent unauthorized Telnet access to a switch port.

B. To limit the number of Layer 2 broadcasts on a particular switch port.

C. To prevent unauthorized hosts from accessing the LAN.

D. To protect the IP and MAC address of the switch and associated ports.

E. To block unauthorized access to the switch management interfaces over common TCP ports.


相关考题:

The network administrator has configured port security on a Ezonexam switch. Why would a network administrator configure port security on this Ezonexam device?A.To prevent unauthorized hosts from getting access to the LANB.To limit the number of Layer 2 broadcasts on a particular switch portC.To prevent unauthorized Telnet or SSH access to a switch portD.To prevent the IP and MAC address of the switch and associated portsE.None of the above

The Ezonexam network administrator wants to ensure that only a single web server can connect to pot Fa0/1 on a catalyst switch. The server is plugged into the switch's Fast Eth. 0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of this server is allowed by switch port Fa0/1? (Choose two)A.Configure port Fa0/1 to accept connections only from the static IP address of the serverB.Configure the MAC address of the server as a static entry associated with port Fa0/1C.Employ a proprietary connector type on Fa0/1 that is incomputable with other host connectorsD.Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the serverE.Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address

Why would a network administrator configure port security on a switch()。 A.to prevent unauthorized Telnet access to a switch portB.to limit the number of Layer 2 broadcasts on a particular switch portC.to prevent unauthorized hosts from accessing the LAND.to protect the IP and MAC address of the switch and associated portsE.to block unauthorized access to the switch management interfaces over common TCP ports

You are the network administrator of a small Layer 2 network with 50 users. Lately, users have been complaining that the network is very slow. While troubleshooting, you notice that the CAM table of your switch is full, although it supports up to 12,000 MAC addresses. How can you solve this issue and prevent it from happening in the future?()A、Upgrade the switchesB、Configure BPDU guardC、Configure VLAN access listsD、Configure port securityE、Configure Dynamic ARP inspection

Why would a network administrator configure port security on a switch?()A、To prevent unauthorized Telnet access to a switch port.B、To limit the number of Layer 2 broadcasts on a particular switch port.C、To prevent unauthorized hosts from accessing the LAN.D、To protect the IP and MAC address of the switch and associated ports.E、To block unauthorized access to the switch management interfaces over common TCP ports.

Why would a network administrator configure port security on a switch?()A、to prevent unauthorized Telnet access to a switch portB、to limit the number of Layer 2 broadcasts on a particular switch portC、to prevent unauthorized hosts from accessing the LAND、to protect the IP and MAC address of the switch and associated portsE、to block unauthorized access to the switch management interfaces over common TCP ports

The network security policy requires that only one host be permitted to attach dynamically to each switch interfacE.If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy? ()A、Switch1(config-if)# switchport port-security maximum 1B、Switch1(config)# mac-address-table secureC、Switch1(config)# access-list 10 permit ip hostD、Switch1(config-if)# switchport port-security violation shutdownE、Switch1(config-if)# ip access-group 10

When using Cisco Network Assistant to configure a WS-CE500-24LC switch, which three are available choices in the port settings window?()A、Duplex mode selectionsB、Auto MDIX selectionsC、Status SelectionsD、Group mode selectionsE、Port security selections

A network administrator needs to configure port security on a switch.which two statements are true?()A、The network administrator can apply port security to dynamic access portsB、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.C、The sticky learning feature allows the addition of dynamically learned addresses to the runningconfiguration.D、The network administrator can apply port security to EtherChannels.E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.

The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy (Choose two.)()。A、Switch1(config-if)# switchport port-security maximum 1B、Switch1(config)# mac-address-table secureC、Switch1(config)# access-list 10 permit ip hostD、Switch1(config-if)# switchport port-security violation shutdownE、Switch1(config-if)# ip access-group 10

A network administrator needs to configure port security on a switch.which two statements are true?()A、The network administrator can apply port security to dynamic access portsB、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.C、The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.D、The network administrator can apply port security to EtherChannels.E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.

A network administrator wants to ensure that only the server can connect to port Fa0/1 on a Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of the server is allowed by switch port Fa0/1?()A、Configure port Fa0/1 to accept connections only from the static IP address of the server.B、Employ a proprietary connector type on Fa0/1 that is incompatible with other host connectors.C、Configure the MAC address of the server as a static entry associated with port Fa0/1.D、Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.E、Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the server.F、Configure an access list on the switch to deny server traffic from entering any port other than Fa0/1.

A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices.What would be the most efficient way to configure MAC-level security on all these ports? ()A、Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.B、Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.C、Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.D、Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?()A、Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address commandB、Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address commandC、Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to themD、Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security

The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy?()A、TestKing1(config-if)# switchport port-security maximum 1B、TestKing1(config)# mac-address-table secureC、TestKing1(config)# access-list 10 permit ip hostD、TestKing1(config-if)# switchport port-security violation shutdownE、TestKing1(config-if)# ip access-group 10

The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy?()A、Switch1(config-if)# switchport port-security maximum 1B、Switch1(config)# mac-address-table secureC、Switch1(config)# access-list 10 permit ip hostD、Switch1(config-if)# switchport p ort-security violation shutdownE、Switch1(config-if)# ip access-group 10

You need to configure port security on switch R1.  Which two statements are true about this  technology? ()A、 Port security can be configured for ports supporting VoIP.B、 With port security configured, four MAC addresses are allowed by default.C、 The network administrator must manually enter the MAC address for each device in order for  the switch to allow connectivity.D、Withsecurity configured, only one MAC addresses is allowed by default.  E、 Port security cannot be configured for ports supporting VoIP.

An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check?()A、 Default gatewayB、 The ports on the switchC、 Port security on the servers switch portD、 Ethernet cable

An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check?()A、Default gatewayB、The ports on the switchC、Port security on the server's switch portD、Ethernet cable

Multiple users call from the same location saying that they have no network connectivity. The administrator is unable to ping the main switch at that IDF. Which of the following configuration management documents would the administrator MOST likely consult to troubleshoot the issue?()A、Baseline configurationB、Security policyC、Performance and transaction logsD、Physical network diagram

多选题When using Cisco Network Assistant to configure a WS-CE500-24LC switch, which three are available choices in the port settings window?()ADuplex mode selectionsBAuto MDIX selectionsCStatus SelectionsDGroup mode selectionsEPort security selections

多选题As a network administrator, you are required to configure a switch port for a private Virtual LAN. In such a situation, which three of the following connection modes will be available during the configuration process? ()(Choose three.)Aisolated modeBmodular modeCcommunity modeDpromiscuous modeEnon-isolatedFpermanent

多选题The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy (Choose two.)()。ASwitch1(config-if)# switchport port-security maximum 1BSwitch1(config)# mac-address-table secureCSwitch1(config)# access-list 10 permit ip hostDSwitch1(config-if)# switchport port-security violation shutdownESwitch1(config-if)# ip access-group 10

单选题An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check?()A Default gatewayB The ports on the switchC Port security on the servers switch portD Ethernet cable

多选题You need to configure port security on switch R1.  Which two statements are true about this  technology? ()APort security can be configured for ports supporting VoIP.BWith port security configured, four MAC addresses are allowed by default.CThe network administrator must manually enter the MAC address for each device in order for  the switch to allow connectivity.DWithsecurity configured, only one MAC addresses is allowed by default.EPort security cannot be configured for ports supporting VoIP.

多选题The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy?()ASwitch1(config-if)# switchport port-security maximum 1BSwitch1(config)# mac-address-table secureCSwitch1(config)# access-list 10 permit ip hostDSwitch1(config-if)# switchport p ort-security violation shutdownESwitch1(config-if)# ip access-group 10

单选题Why would a network administrator configure port security on a switch()。Ato prevent unauthorized Telnet access to a switch portBto limit the number of Layer 2 broadcasts on a particular switch portCto prevent unauthorized hosts from accessing the LANDto protect the IP and MAC address of the switch and associated portsEto block unauthorized access to the switch management interfaces over common TCP ports

单选题Why would a network administrator configure port security on a switch?()ATo prevent unauthorized Telnet access to a switch port.BTo limit the number of Layer 2 broadcasts on a particular switch port.CTo prevent unauthorized hosts from accessing the LAN.DTo protect the IP and MAC address of the switch and associated ports.ETo block unauthorized access to the switch management interfaces over common TCP ports.