How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。A、If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.B、If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.C、If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.D、If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.E、If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.F、If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。
- A、If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.
- B、If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.
- C、If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.
- D、If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.
- E、If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.
- F、If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
相关考题：
Cisco is the leader in the router market space. What basic functions do their routers perform. in a network? (Choose two)A. The microsegmentation of broadcast domainsB. Path selectionC. Packet switchingD. Bridging between LAN segmentsE. Access layer securityF. VLAN membership assignmentG. Application optimization
How is an RSVP resv message sent back to the ingress router?() A. reverse path of the RROB. least cost to the ingress routerC. shortest path to the egress routerD. reverse path of the path vector TLV
What is the term "ordered control" mean regarding how MPLS LSPs are established?() A. establish starting at the egress router going back to the ingress routerB. establish starting at the ingress router going downstream to the egress routerC. establish when a router learns of a new prefixD. establish when the path correctly matches the reverse path forwarding check
Given the following LSP configuration, which statement is true?（）label-switched-path lsp-xyz { to 10.200.1.1; primary path1; secondary path2; secondary path3; no-cspf; } path path1 { 10.200.10.1 strict; } path path2 { 10.200.20.1 strict; } path path3 { 10.200.30.1 loose; }A. The router will use path1 when it is available and stable.B. The router will use path3 when it is available and stable.C. The router will attempt to establish path2 only when path1 and path3 are down.D. The router will attempt to establish path1 only when path2 and path3 are down.
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? () A. Router A will prefer the path through router B for network 172.20.0.0B. Router A will prefer the path through router C for network 172.20.0.0C. Packets from router D will prefer the path through router B for networks advertised by router AD. Packets from r outer D will prefer the path through router C for networks advertised by router A
What is the purpose using the traceroute command?（）A、to map all the devices on a network.B、to display the current TCP/IP configuration values.C、to see how a device MAC address is mapped to its IP address.D、to see the path a packet will take when traveling to a specified destination.E、to display the MTU values for each router in a specified network path from source to a destination.
Which of these statements accurately identifies how Unicast Reverse Path Forwarding can be employed to prevent the use of malformed or forged IP sources addresses？（）A、It is applied only on the input interface of a router.B、It is applied only on the output interface of a router.C、It can be configured either on the input or output interface of a router.D、It cannot be configured on a router interface.E、It is configured under any routing protocol process.
When the BGP path selection process is being performed on a Cisco router, which BGP attribute is used first when determining the best path?（）A、local preferenceB、MEDC、weightD、or iginE、next - hopF、AS - path
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）A、To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50B、Th e router will prefer the shortest autonomous system pathC、If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MEDD、The router will prefer the route with the lower MED
For a router connected to two ISPs for redundancy， using IPSLA and static routing， how would you configure uRPF on the uplink interface？（）A、ip verify unicast source reachable-via anyB、ip verify unicast reverse-pathC、ip verify unicast reverse-path looseD、ip verify unicast reverse-path strict
Which of the following are shared distribution tree characteristics？ （Choose all that apply.）（）A、Memory requirements are higher for shared distribution tree than for source distribution treeB、Creates a tree from a central RP to all last-hop routersC、Uses a rendezvous pointD、An optimal path is created between each source router and each last-hop routerE、Place （S，G） entry in each router’s multicast routing tableF、Place （*，G） entry in a router’s multicast routing to table
Given the following LSP configuration， which statement is true？（） label-switched-pathlsp-xyz { to 10.2000.1.1； primarypath1； secondarypath2； secondarypath3； no-cspf； } pathpath1 { 10.200.10.1 strict； } pathpath2 { 10.200.20.1 strict； } pathpath3 { 10.200.30.1loose }A、The router will use path1 when it is available and stable.B、The router will use path3 when it is available and stable.C、The router will attempt to establish path2 only when path1 and path3 are down.D、The router will attempt to establish path1 only when path2 and path3 are down.
What is the optimize timer on an RSVP-signaled Label-Switched Path （LSP）？（）A、the time it takes to identify the optimal path for the LSPB、the interval at which the ingress router recalculates the LSP’s pathC、the time the ingress router takes to establish the primary pathD、the maximum number of times the ingress router tries to establish the primary path
What is the optimize timer on an RSVP-signaled Label-Switched Path (LSP)?（）A、The time it takes to identify the optimal path for the LSP.B、The interval at which the ingress router recalculates the LSP's path.C、The time the ingress router takes to establish the primary path.D、The maximum number of times the ingress router tries to establish the primary path.
单选题What is the purpose using the traceroute command?（）Ato map all the devices on a network.Bto display the current TCP/IP configuration values.Cto see how a device MAC address is mapped to its IP address.Dto see the path a packet will take when traveling to a specified destination.Eto display the MTU values for each router in a specified network path from source to a destination.
单选题How is an RSVP resv message sent back to the ingress router？（）A reverse path of the RROB least cost to the ingress routerC shortest path to the egress routerD reverse path of the path vector TLV
单选题Given the following LSP configuration， which statement is true？（） label-switched-pathlsp-xyz { to 10.2000.1.1； primarypath1； secondarypath2； secondarypath3； no-cspf； } pathpath1 { 10.200.10.1 strict； } pathpath2 { 10.200.20.1 strict； } pathpath3 { 10.200.30.1loose }AThe router will use path1 when it is available and stable.BThe router will use path3 when it is available and stable.CThe router will attempt to establish path2 only when path1 and path3 are down.DThe router will attempt to establish path1 only when path2 and path3 are down.
单选题Given the following LSP configuration, which statement is true?（）label-switched-path lsp-xyz { to 10.200.1.1; primary path1; secondary path2; secondary path3; no-cspf; } path path1 { 10.200.10.1 strict; } path path2 { 10.200.20.1 strict; } path path3 { 10.200.30.1 loose; }AThe router will use path1 when it is available and stable.BThe router will use path3 when it is available and stable.CThe router will attempt to establish path2 only when path1 and path3 are down.DThe router will attempt to establish path1 only when path2 and path3 are down.
单选题For a router connected to two ISPs for redundancy， using IPSLA and static routing， how would youconfigure uRPF on the uplink interface？（）Aip verify unicast source reachable-via anyBip verify unicast reverse-pathCip verify unicast reverse-path looseDip verify unicast reverse-path strict
单选题What is the optimize timer on an RSVP-signaled Label-Switched Path (LSP)?（）AThe time it takes to identify the optimal path for the LSP.BThe interval at which the ingress router recalculates the LSP's path.CThe time the ingress router takes to establish the primary path.DThe maximum number of times the ingress router tries to establish the primary path.
单选题What is the term "ordered control" mean regarding how MPLS LSPs are established?（）Aestablish starting at the egress router going back to the ingress routerBestablish starting at the ingress router going downstream to the egress routerCestablish when a router learns of a new prefixDestablish when the path correctly matches the reverse path forwarding check
单选题How is an RSVP resv message sent back to the ingress router?（）Areverse path of the RROBleast cost to the ingress routerCshortest path to the egress routerDreverse path of the path vector TLV
单选题Given the following LSP configuration, which statement is true? （）A The router will use path1 when it is available and stable.B The router will use path3 when it is available and stable.C The router will attempt to establish path2 only when path1 and path3 are down.D The router will attempt to establish path1 only when path2 and path3 are down.
单选题What is the optimize timer on an RSVP-signaled Label-Switched Path （LSP）？（）Athe time it takes to identify the optimal path for the LSPBthe interval at which the ingress router recalculates the LSP’s pathCthe time the ingress router takes to establish the primary pathDthe maximum number of times the ingress router tries to establish the primary path
单选题Which of these statements accurately identifies how Unicast Reverse Path Forwarding can be employed to prevent the use of malformed or forged IP sources addresses？（）AIt is applied only on the input interface of a router.BIt is applied only on the output interface of a router.CIt can be configured either on the input or output interface of a router.DIt cannot be configured on a router interface.EIt is configured under any routing protocol process.
多选题How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。AIf RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.BIf RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.CIf EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.DIf EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.EIf EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.FIf EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
多选题You are troubleshooting a routing issue and need to check the hop-by-hop path to the 10.10.10.10 destination. Which three commands would display the path?（）Auser@router# traceroute 10.10.10.10Buser@router ping record-route 10.10.10.10Cuser@routertraceroute 10.10.10.10Duser@router# run traceroute 10.10.10.10Euser@router# ping record-route 10.10.10.10