A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）A、To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50B、Th e router will prefer the shortest autonomous system pathC、If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MEDD、The router will prefer the route with the lower MED
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）
- A、To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
- B、Th e router will prefer the shortest autonomous system path
- C、If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
- D、The router will prefer the route with the lower MED
相关考题：
Which two conditions, when met, allow an IS－IS Level 2 router to be considered attached?() A. You can reach other Level 2 routers.B. It can reach at least one other defined area.C. The router is reachable by at least two ES-IS nodes.D. It has at least one enabled reachable prefix with a valid metric defined.
Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol
Refer to the exhibit. Which two statements are true?() A. DHCPDISCOVER packets will reach the DHCP server.B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.C. This configuration is applied to interface Fa0/1.D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.F. This configuration is applied to interface Fa0/0.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A. the OSPF routeB. the EIGRP routeC. the RIPv2 routeD. all three routesE. the OSPF and RIPv2 routes
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）A、The central site router has 100 fully adjacent neighborships with the 100 branchesB、The central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesC、The central site router has a neighborship with the Frame Relay switcHD、None of the other answers is correct
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
The Testking network is utilizing RIP as the IP routing protocol. Router TK1 learns how to reach the same destination via 6 different paths. All paths have the same metric and administrative distance. With all routers using the default operation,which of the paths will be chosen to reach the destination?（）A、Only the first two paths that are learned.B、Four of the paths.C、All six routes in a routed robin fashion.D、The oldest two paths in the routing table.E、The first path learned to the destination network.
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
Companycom is implementing a pair of Virtual IO Servers to service four LPARs. If each operating system image requires 15GB of disk space, what is the minimum amount of SCSI resource necessary?（）A、Two SCSI paths and two 73GB SCSI disksB、Two SCSI paths and two 36GB SCSI disksC、Four SCSI paths and four 73GB SCSI disksD、Two dual port SCSI RAID adapters with two 73GB SCSI disks
A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How can you accomplish this task,using the fewest physical interfaces and without decreasing network performance?（）A、Add two more FastEthernet interfaces.B、Add a second router to handle the vlan traffic.C、Use a hub to connect the four vlans with a FastEthernet interface on router.D、Implement a router-on-a-stick configuration.
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A、the OSPF routeB、the EIGRP routeC、the RIPv2 routeD、all three routesE、the OSPF and RIPv2 routes
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
Which two conditions, when met, allow an IS-IS Level 2 router to be considered attached?（）A、You can reach other Level 2 routers.B、It can reach at least one other defined area.C、The router is reachable by at least two ES-IS nodes.D、It has at least one enabled reachable prefix with a valid metric defined.
单选题A router has two FastEthernet interfaces and needs to connect to four vlans in the local network.How canyou accomplish this task，using the fewest physical interfaces and withoutdecreasing networkperformance？（）AAdd two more FastEthernet interfaces.BAdd a second router to handle the vlan traffic.CUse a hub to connect the four vlans with a FastEthernet interface on router.DImplement a router-on-a-stick configuration.
多选题HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？ （）AHSRP provides redundancy and fault toleranceBHSRP allows one router to automatically assume the function of the second router if the second router failsCHSRP allows one router to automatically assume the function of the second router if the second router startsDHSRP provides redundancy and load balancing
单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）AoneBthreeCtwoDzero
单选题Two Label-Switched Paths called LSP A and LSP B have been configured on a router. LSP A has been configured with a hold-priority of 3. There is insufficient reservable bandwidth along the path to accomodate both LSPs reservation requirements. Which setup priority must LSP B have to pre-empt LSP A and use its bandwidth?（）A2B3C4D7
单选题A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）ATo influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50BTh e router will prefer the shortest autonomous system pathCIf the command bgp always - compare - med has been given, then the router will prefer the route with the highest MEDDThe router will prefer the route with the lower MED
多选题Which two conditions, when met, allow an IS-IS Level 2 router to be considered attached?（）AYou can reach other Level 2 routers.BIt can reach at least one other defined area.CThe router is reachable by at least two ES-IS nodes.DIt has at least one enabled reachable prefix with a valid metric defined.
单选题A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）AThe central site router has 100 fully adjacent neighborships with the 100 branchesBThe central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesCThe central site router has a neighborship with the Frame Relay switcHDNone of the other answers is correct
单选题You have two EBGP peers connected via two parallel serial lines. What should you do to be able to load-balance between two EBGP speakers over the parallel serial lines in both directions？ （）Anothing，BGP automatically load-balances the traffic between different autonomous systems on all available linksBpeer between the eBGP speaker’s loopbacks， configuring eBGP multihop as required， and use an IGP to load-share between the two equal-cost paths between the loopback addressesCconfigure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the EBGP peer loopback address；it is also necessary to use the next-hop-self commandDuse the ebgp-load-balance command on the neighbor statement on both sidesEconfigure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the peer loopback address；it is also necessary to use the ebgp-multihop and next-hop-self commands
单选题Companycom is about to purchase a POWER5 Enterprise server which requires two Ethernet ports and two disks for each of the four LPARs. It has been configured and validated using the IBM eConfig tool. Which of the following is very important to verify in addition to the eConfig validation?（）ATotal number of SCSI adaptersBTotal number of Ethernet adaptersCTotal number of Ethernet adapters and number of SCSI paths per LPARDTotal number of SCSI paths available and total number of SCSI adapters
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router