You configured an interface with an IP address and committed the change. You then committed a change that added an exception in a firewall filter to allow this network through the filter. You realize that this work was done on the wrong router. How do you undo all these changes?（）A、rollback 2B、rollback 1C、rollback 0D、rollback 3
You configured an interface with an IP address and committed the change. You then committed a change that added an exception in a firewall filter to allow this network through the filter. You realize that this work was done on the wrong router. How do you undo all these changes?（）
- A、rollback 2
- B、rollback 1
- C、rollback 0
- D、rollback 3
相关考题：
You have two IP addresses configured on the ge-0/0/6 interface, as shown in the exhibit. You want to select the 172.16.10.101 address as the source address for packets sent from this interface to hosts on a remote subnet.Which parameter would you add to the 172.16.10.101 address to complete this task?（）A. preferredB. broadcastC. primaryD. arp 172.16.10.101
After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"() A.Layer 1 on the interface is up but Layer 2 is down.B.Layer 2 on the interface is up but Layer 3 has not been configured.C.The interface is administratively up but the link status is down.D.The interface is up but has been administratively turned off.
You work as a network engineer at TestKing.com. TestKing users have noticed extremely slow network performance, intermittent connectivity, and connection loss. After entering the show interfaces command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem?（）A. duplex mismatchB. a routing loopC. trunking mode mismatchD. improperly configured root bridgeE. improperly configured static VLAN
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?() A.There is a mismatch in encapsulation typesB.The wrong type of cable is connected to the interfaceC.The interface has been configured with the shutdown commandD.The interface is not receiving any keepalivesE.The interface needs to be configured as a DTE deviceF.There is no encapsulation type configured
How many IP addresses can be configured in a given interface?（）A、one primary and one secondary IP addressB、one IP addressC、as many IP addresses as you wantD、one primary and multiple secondary IP addresses
Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to an interface（）A、The interface must be configured as a Multilink PPP interface.B、The correct bandwidth should be configured on the interface.C、A QoS policy must not be currently attached to the interface.D、CEF must be enableE、AutoQoS must be enabled globally before it can be enabled on the interface.F、An IP address must be configured on the interface if its speed is equal to or less than 768 kbps.
You are using AutoQoS Enterprise and realize that the results are not what you expected. Whichof the following are possible reasons for AutoQoS not functioning correctly？（Choose all thatapply.）（）A、The interface you configured for AutoQoS is set to half-duplexB、AutoQoS was configured on only one end of the linkC、The interface you configured for AutoQoS has no IP addressD、The interface’s bandwidth is not correctly configuredE、CEF is not enabled on the interfaceF、You enabled AutoQoS on the interface but forgot to enable globally first
You use Microsoft .Net Framework 4 to create a Windows Form application. You created a new application, you then wrote the code below: Thread.CurrentThread.CurrentUICulture = Thread.CurrentThread.CurrentCulture Which of the following options are TRUE? （）A、The user interface will make use of the currently configured culture settings in the Control Panel at present.B、The user interface will make use of new culture settings.C、The user interface will make use of the culture settings that were installed with the operating system.
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）A、There is a mismatch in encapsulation typesB、The wrong type of cable is connected to the interfaceC、The interface has been configured with the shutdown commandD、The interface is not receiving any keepalivesE、The interface needs to be configured as a DTE deviceF、There is no encapsulation type configured
You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A、The Frame Relay encapsulation on the physical interface.B、The local DLCI on each subinterface.C、An IP address on the physical interface.D、The subinterface type as point-to-point.
Which command will allow you to display the configured QoS group and the ingress buffer allocated to each QoS group？（）A、 show interface priority-flow-controlB、 show interface queuingC、 show queuing interfaceD、 show policy-map system type queuingE、 show policy-map interface ethernet type queuing
Which two statements are true about the primary address on an interface?（）A、It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface.B、You use the primary address when you have multiple IP addresses belonging to the same subnet on the same interface.C、It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface.D、By default, the primary address on an interface is selected as the numerically highest local address configured on the interface.
You use Microsoft .NET Framework 4 to create a Windows Forms application. You created a new application, you then wrote the code below: Thread.CurrentThread.CurrentUICulture = Thread.CurrentThread.CurrentCulture; Which of the following options are TRUE?（）A、The user interface will make use of the currently configured culture settings in the Control Panel at present.B、The user interface will make use of new culture settings.C、The user interface will have no culture settings.D、The user interface will make use of the culture settings that were installed with the operating system.
单选题After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"（）ALayer 1 on the interface is up but Layer 2 is down.BLayer 2 on the interface is up but Layer 3 has not been configured.CThe interface is administratively up but the link status is down.DThe interface is up but has been administratively turned off.
单选题You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）AThe Frame Relay encapsulation on the physical interface.BThe local DLCI on each subinterface.CAn IP address on the physical interface.DThe subinterface type as point-to-point.
单选题You have just configured the network interface on systemA . The following information is From systemB， you test the network connectivity by sending ICMP ECHO_REQUEST packets to systemA. The following message is displayed： no answer from systemA What is most likely the problem？（）A The interface is not plumbed.B The interface is not configured.C The interface does not have valid routes configured.D The interface is not marked as
多选题Youe just configured the network interface on You？e just configured the network interface on systemA and the following information is displayed pertaining to systemA’s network interface： You have been instructed to change the name of this system to systemB. Which four files need to be modified to change the name of this system from systemA to systemB？ （）A/etc/nodenameB/etc/hostname.rtls0C/etc/hostnameD/etc/inet/hostsE/etc/domainnameF/etc/inet/ipnodesG/etc/inetd.conf
单选题You use Microsoft .NET Framework 4 to create a Windows Forms application. You created a new application, you then wrote the code below: Thread.CurrentThread.CurrentUICulture = Thread.CurrentThread.CurrentCulture; Which of the following options are TRUE?（）AThe user interface will make use of the currently configured culture settings in the Control Panel at present.BThe user interface will make use of new culture settings.CThe user interface will have no culture settings.DThe user interface will make use of the culture settings that were installed with the operating system.
单选题You use Microsoft .Net Framework 4 to create a Windows Form application. You created a new application, you then wrote the code below: Thread.CurrentThread.CurrentUICulture = Thread.CurrentThread.CurrentCulture Which of the following options are TRUE? （）AThe user interface will make use of the currently configured culture settings in the Control Panel at present.BThe user interface will make use of new culture settings.CThe user interface will make use of the culture settings that were installed with the operating system.
单选题Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）AThere is a mismatch in encapsulation typesBThe wrong type of cable is connected to the interfaceCThe interface has been configured with the shutdown commandDThe interface is not receiving any keepalivesEThe interface needs to be configured as a DTE deviceFThere is no encapsulation type configured
单选题You work as a network engineer at TestKing.com. TestKing users have noticed extremely slow network performance, intermittent connectivity, and connection loss. After entering the show interfaces command, you notice that the Ethernet interface is configured as 100 Mbps full-duplex and that there is evidence of late collisions. What could be the cause of this problem?（）Aduplex mismatchBa routing loopCtrunking mode mismatchDimproperly configured root bridgeEimproperly configured static VLAN
多选题Which two statements are true about the primary address on an interface? （）AIt is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interfaceBYou use the primary address when you have multiple IP addresses belonging to the same subnet on the same intefaceCIt can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interfaceDBy default, the primary address on an interface is selected as the nmerically highest local address configured on the interface
多选题Which two statements are true about the primary address on an interface?（）AIt is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface.BYou use the primary address when you have multiple IP addresses belonging to the same subnet on the same interface.CIt can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface.DBy default, the primary address on an interface is selected as the numerically highest local address configured on the interface.
单选题You configured an interface with an IP address and committed the change. You then committed a change that added an exception in a firewall filter to allow this network through the filter. You realize that this work was done on the wrong router. How do you undo all these changes?（）Arollback 2Brollback 1Crollback 0Drollback 3
单选题Which command will allow you to display the configured QoS group and the ingress buffer allocated to each QoS group？（）A show interface priority-flow-controlB show interface queuingC show queuing interfaceD show policy-map system type queuingE show policy-map interface ethernet type queuing
单选题Your network contains a single Active Directory domain. All servers run Windows Server 2008 R2. A DHCP server is deployed on the network and configured to provide IPv6 prefixes.You need to ensure that when you monitor network traffic,you see the interface identifiers derived from the Extended Unique Identifier (EUI)-64 address.Which command should you run?（）Anetsh.exe interface ipv6 set global addressmaskreply=disabledBnetsh.exe interface ipv6 set global dhcpmediasense=enabledCnetsh.exe interface ipv6 set global randomizeidentifiers=disabledDnetsh.exe interface ipv6 set privacy state=enabled
多选题You are using AutoQoS Enterprise and realize that the results are not what you expected. Whichof the following are possible reasons for AutoQoS not functioning correctly？（Choose all thatapply.）（）AThe interface you configured for AutoQoS is set to half-duplexBAutoQoS was configured on only one end of the linkCThe interface you configured for AutoQoS has no IP addressDThe interface’s bandwidth is not correctly configuredECEF is not enabled on the interfaceFYou enabled AutoQoS on the interface but forgot to enable globally first
多选题You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）AEIGRP for IPv6 is directly configured on the interfaces over which it runs.BEIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.CThere is a network statement configuration in EIGRP for IPv6， the same as for IPv4.DThere is no network statement configuration in EIGRP for IPv6.EWhen a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.FWhen a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive