多选题Half of your network uses RIPv2 and the other half runs OSPF. The networks do not communicate with each other. Which two of these factors describe the impact of activating EIGRP over each separate part？（）AEIGRP will not be accepted when configured on the actual RIPv2 routers.BOSPF will no longer be used in the routing table， because you only have EIGRP internal routes running.COSPF will no longer be used in the routing table， because you only have EIGRP external routes running.DRIPv2 will populate its RIP database but not its routing table， because you only have EIGRP external routes running.ERIPv2 will populate its RIP database but not its routing table， because you only have EIGRP internal routes running.FOSPF database will have RIPv2 routes.
多选题
Half of your network uses RIPv2 and the other half runs OSPF. The networks do not communicate with each other. Which two of these factors describe the impact of activating EIGRP over each separate part？（）
A
EIGRP will not be accepted when configured on the actual RIPv2 routers.
B
OSPF will no longer be used in the routing table， because you only have EIGRP internal routes running.
C
OSPF will no longer be used in the routing table， because you only have EIGRP external routes running.
D
RIPv2 will populate its RIP database but not its routing table， because you only have EIGRP external routes running.
E
RIPv2 will populate its RIP database but not its routing table， because you only have EIGRP internal routes running.
F
OSPF database will have RIPv2 routes.
参考解析
解析：
暂无解析
相关考题：
You want to upgrade the Ezonexam LAN so that all ports operate in full duplex mode. Which statement is true about full-duplex Ethernet when comparing to half-duplex Ethernet?A．Full-duplex Ethernet consists of a shared cable segment. Half-duplex provides a point-to-point linkB．Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receiveC．Full-duplex Ethernet can provide higher throughput than can half-duplex Ethernet of the same bandwidthD．Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex Ethernet uses a jam signalE．None of the above
The Ezonexam LAN is upgrading all devices to operate in full duplex. Which statement is true about full-duplex Ethernet in comparison to half-duplex Ethernet?A．Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receiveB．Full-duplex Ethernet consists of a shared cable segment. Half-duplex Ethernet provides a point-to-point linkC．Full-duplex Ethernet can provide higher throughout than can half-duplex Ethernet of the same bandwidthD．Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex ethernet uses a jam signalE．None of the above
It was ( )ride from the school to the downtown. A、an half hour’sB、half an hourC、half an hour’sD、half a hour’s
How long has your daughter been missing?().A. I miss my daughter a lot.B. We haven't seen each other for two months.C. About half an hour. I've been looking for her everywhere.
One half of the earth is in darkness _______ the other half is bright.A、asB、whileC、sinceD、because
Which of the following statements correctly describe the differences between half-duplex and full-duplex Ethernet? (Select two answer choices.)A．Full-duplex Ethernet uses CSMA/CD to prevent collisions.B．Half-duplex Ethernet uses a loopback circuit to detect collisions.C．A full-duplex Ethernet card allows 20Mbps for data transmission.D．Full-duplex Ethernet makes use of two pairs of wires for data.E．An Ethernet hub can operate both half and full duplex simultaneously.
The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?A．Assign the switch a higher MAC address than the other switches in the network haveB．Establish a direct link from the switch to all other switches in the networkC．Configure the switch full-duplex operation and configure the other switches for half-duplex operationD．Configure the switch so that it has lower priority than other switches in the networkE．None of the above
Which three characteristics apply to IS － IS but not to OSPF?() A. uses a default IOS metric of 10 on each interfaceB. uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDNC. uses a DIS and a backup DIS to present the psuedo - node on the LAND. encapsulates PDUs directly into a data - link frameE. uses stubby areas to improve network scalabilityF. runs PRC (Partial Route Calculations) to calculate IP re achability information
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A. the OSPF routeB. the EIGRP routeC. the RIPv2 routeD. all three routesE. the OSPF and RIPv2 routes
23 I'll spend half of my holiday practicing English and————————half learning drawingA anotherB the otherC other’sD other
Of the people who work here, _________ are French and _________ English.A.half... halfB.the half... the halfC.a half... a halfD.a half... the half
Yesterday we had （） talk.Aone and a half hour’sBone and a half hourCan hour and a half’sDan hour’s and a half
Yesterday we had （） talk.A、one and a half hour’sB、one and a half hourC、an hour and a half’sD、an hour’s and a half
Half of your network uses RIPv2 and the other half runs OSPF. The networks do not communicate with each other. Which two of these factors describe the impact of activating EIGRP over each separate part？ （）A、EIGRP will not be accepted when configured on the actual RIPv2 routers.B、OSPF will no longer be used in the routing table， because you only have EIGRP internal routes running.C、OSPF will no longer be used in the routing table， because you only have EIGRP external routes running.D、RIPv2 will populate its RIP database but not its routing table， because you only have EIGRP external routes running.E、RIPv2 will populate its RIP database but not its routing table， because you only have EIGRP internal routes running.F、OSPF database will have RIPv2 routes.
Which statement about OSPF authentication is true？（）A、To enable OSPF authentication in a network， OSPF area 0 authentications must be enabled firstB、The payload of OSPF version 3 packets contains no authentication informationC、OSPF version 3 supports Advanced Encryption StandardD、OSPF version 3 uses router ID as a key to encrypt OSPF hello packetsE、OSPF MD5 authentication uses TCP， and Plan Test authentication uses UDP
Which three characteristics apply to IS - IS but not to OSPF?（）A、uses a default IOS metric of 10 on each interfaceB、uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDNC、uses a DIS and a backup DIS to present the psuedo - node on the LAND、encapsulates PDUs directly into a data - link frameE、uses stubby areas to improve network scalabilityF、runs PRC (Partial Route Calculations) to calculate IP re achability information
Which of the following statements correctly describe the differences between half-duplex and full-duplex Ethernet?（）A、Full-duplex Ethernet uses CSMA/CD to prevent collisions.B、Half-duplex Ethernet uses a loopback circuit to detect collisions.C、A full-duplex Ethernet card allows 20Mbps for data transmission.D、Full-duplex Ethernet makes use of two pairs of wires for data.E、An Ethernet hub can operate both half and full duplex simultaneously.
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A、Establish a direct link from the switch to all other switches in the network.B、Assign the switch a higher MAC address than the other switches in the network have.C、Configure the switch so that it has a lower priority than other switches in the network.D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A、the OSPF routeB、the EIGRP routeC、the RIPv2 routeD、all three routesE、the OSPF and RIPv2 routes
A co-worker is developing an implementation plan for a design that uses OSPF 2 and RIPv2 routing domains, with two routers redistributing between the two domains.The co- worker asks your help in choosing how to prevent domain loops by setting administrative distance. Assuming all other related settings use defaults, which of the following would solve the domain loop problem?（）A、The distance ospf intra - area 80 inter - area 80 OSPF subcommandB、T he distance ospf external 80 OSPF subcommandC、The distance ospf intra - area 180 inter - area 180 OSPF subcommandD、The distance ospf external 180 OSPF subcommand
You are the network administrator for .Your network consists of a single Active Directory domain named . The Default Domain Group Policy object (GPO) uses all default settings. The network contains five servers running Windows Server 2003 and 800 client computers. Half of the client computers are portable computers. The other half are desktop computers. Users of portable computers often work offline, but users of desktop computers do not. You install Windows XP Professional on all client computers with default settings. Then you configure user profiles and store them on the network. Some users of portable computers now report that they cannot log on to their computers. Other users of portable computers do not experience this problem. You need to ensure that all users of portable computers can log on successfully,whether they are working online or offline. What should you do?（）A、Configure all portable computers to cache user credentials locally.B、Ensure that all users of portable computers log on to the network at least once before working offline.C、In all portable computers, rename Ntuser.dat to Ntuser.man.D、For all portable computers, configure the Loopback policy setting.
You have a file server named Server1 that runs Windows Server 2003 Service Pack (SP2). Server1 has a 10-gigabit network adapter and is connected to a 100-Mb switch. You replace the 100-Mb switch by using a 1-GB switch. You discover that copying files to Server1 over the network is slow. You need to reduce the amount of time it takes to copy files to Server1 over the network. Which connection type should you specify for the network adapter? （）A、1-gigabit half-duplexB、1-gigabit full-duplexC、10-gigabit half-duplexD、10-gigabit full-duplex
单选题A co-worker is developing an implementation plan for a design that uses OSPF 2 and RIPv2 routing domains, with two routers redistributing between the two domains.The co- worker asks your help in choosing how to prevent domain loops by setting administrative distance. Assuming all other related settings use defaults, which of the following would solve the domain loop problem?（）AThe distance ospf intra - area 80 inter - area 80 OSPF subcommandBT he distance ospf external 80 OSPF subcommandCThe distance ospf intra - area 180 inter - area 180 OSPF subcommandDThe distance ospf external 180 OSPF subcommand
单选题You need to design a configuration for the mailbox servers. What should you do？（）ACreate two Exchange Server 2003 computers. Place the mailboxes for main office users on one server， and place the mailboxes for remote users on the other serverBCreate a Network Load Balancing cluster that contains two Exchange Server 2003 computers. Place half of the user mailboxes on one server， and place half of the user mailboxes on the other serverCCreate a Microsoft Cluster Server cluster that contains two Exchange Server 2003 computers. Place all of the user mailboxes on one server and configure the other server as a failover nodeDCreate a Microsoft Cluster Server cluster that contains two Exchange Server 2003 computers. Place half of the user mailboxes on one server， and place half of the user mailboxes on the other server
单选题Which statement about OSPF authentication is true？（）ATo enable OSPF authentication in a network， OSPF area 0 authentications must be enabled firstBThe payload of OSPF version 3 packets contains no authentication informationCOSPF version 3 supports Advanced Encryption StandardDOSPF version 3 uses router ID as a key to encrypt OSPF hello packetsEOSPF MD5 authentication uses TCP， and Plan Test authentication uses UDP
多选题Half of your network uses RIPv2 and the other half runs OSPF. The networks do not communicate with each other. Which two of these factors describe the impact of activating EIGRP over each separate part？（）AEIGRP will not be accepted when configured on the actual RIPv2 routers.BOSPF will no longer be used in the routing table， because you only have EIGRP internal routes running.COSPF will no longer be used in the routing table， because you only have EIGRP external routes running.DRIPv2 will populate its RIP database but not its routing table， because you only have EIGRP external routes running.ERIPv2 will populate its RIP database but not its routing table， because you only have EIGRP internal routes running.FOSPF database will have RIPv2 routes.
单选题Which statement is true about full-duplex Ethernet in comparison to half-duplex Ethernet?（）AFull-duplex Ethernet consists of a shared cable segment. Half-duplex Ethernet provides a point-to-point link.BFull-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex Ethernet uses a jam signal.CFull-duplex Ethernet can provide higher throughput than can half-duplex Ethernet of the same bandwidth.DFull-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receive.