单选题Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 1 tunnel source loopback 1 tunnel destination 192.168.1.2 tunnel mode ipv6ip isatap ipv6 address 2000::/64 eui - 64A2000::1311:11F F:FE11:1111B2000::C0A5:101C2000:C0A5:101::D2000::5EFE:C0A5:101
单选题
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 1 tunnel source loopback 1 tunnel destination 192.168.1.2 tunnel mode ipv6ip isatap ipv6 address 2000::/64 eui - 64
A
2000::1311:11F F:FE11:1111
B
2000::C0A5:101
C
2000:C0A5:101::
D
2000::5EFE:C0A5:101
参考解析
解析：
暂无解析
相关考题：
The Ezonexam network administrator wants to ensure that only a single web server can connect to pot Fa0/1 on a catalyst switch. The server is plugged into the switch's Fast Eth. 0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of this server is allowed by switch port Fa0/1? (Choose two)A．Configure port Fa0/1 to accept connections only from the static IP address of the serverB．Configure the MAC address of the server as a static entry associated with port Fa0/1C．Employ a proprietary connector type on Fa0/1 that is incomputable with other host connectorsD．Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the serverE．Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1‘s (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.Which of the following occurs？（）A.Fa0/0 failsB.The command is rejecteDC.The existing three neighbors failD.The neighborship with 172.16.2.20 fails and then reestablishesE.None of the other answers is correct
Refer to the graphic.Host A is communicating with the seiver. What will be the source MAC address of the frames received by Host A from the server?() A.the MAC address of the seiver network interfaceB.the MAC address of host AC.the MAC address of router interface e 1D.the MAC address of router interface e0
If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network()。 A.R1 will forward the packet out all interfaces.B.R1 will drop this packet because this it is not a valid IP address.C.As R1 forwards the frame containing this packet, Sw-A will add 192.168.1.255 to its MAC table.D.R1 will encapsulate the packet in a frame with a destination MAC address of FF-FF-FF-FF-FF-FFE.As R1 forwards the frame containing this packet, Sw-A will forward it to the device assigned the IP address of 192.168.1.255.
Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1（）。A、The MAC address of the NIC in Host 1B、The MAC address of the NIC in server 1C、The MAC address of the Fa0/0 interface of router R1D、The MAC address of the s0/0/0 interface of the router R2
Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100A、The output describes the contents of a Type 5 LSAB、3.3.3.3 identifies a ro uter as being the router performing redistributionC、R1's metric for its best route to reach the router with RID 9.9.9.9 is 100D、The router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。A、The IP address of sever 1.B、The MAC address of NIC in sever 1.C、The IP address of F0/0 interface of router R1.D、The MAC address of the Fa0/0 interface of router R1.E、The IP address of the s0/0/0 interface of router R2F、The MAC address of the s0/0/0 interface of router R2
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）A、Fa0/0 failsB、The command is rejecteDC、The existing three neighbors failD、The neighborship with 172.16.2.20 fails and then reestablishesE、None of the other answers is correct
A network administrator wants to ensure that only the server can connect to port Fa0/1 on a Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of the server is allowed by switch port Fa0/1?（）A、Configure port Fa0/1 to accept connections only from the static IP address of the server.B、Employ a proprietary connector type on Fa0/1 that is incompatible with other host connectors.C、Configure the MAC address of the server as a static entry associated with port Fa0/1.D、Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.E、Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the server.F、Configure an access list on the switch to deny server traffic from entering any port other than Fa0/1.
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）A、172.16.0.1/23B、172.16.1.1/26C、172.16.1.1/24D、172 .16.0.255/23E、None of the other answers is correct.
Which destination addresses will be used by Host A to send data to Host C?（）A、the IP address of Switch 1B、the MAC address of Switch 1C、the IP address of Host CD、the MAC address of Host CE、the IP address of the router's E0 interfaceF、the MAC address of the router's E0 interface
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B、S0/2 may currently be in a state other than up/up.C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D、S0/2 may be configured as a passive inter face.
If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network（）。A、R1 will forward the packet out all interfaces.B、R1 will drop this packet because this it is not a valid IP address.C、As R1 forwards the frame containing this packet, Sw-A will add 192.168.1.255 to its MAC table.D、R1 will encapsulate the packet in a frame with a destination MAC address of FF-FF-FF-FF-FF-FFE、As R1 forwards the frame containing this packet, Sw-A will forward it to the device assigned the IP address of 192.168.1.255.
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 1 tunnel source loopback 1 tunnel destination 192.168.1.2 tunnel mode ipv6ip isatap ipv6 address 2000::/64 eui - 64A、2000::1311:11F F:FE11:1111B、2000::C0A5:101C、2000:C0A5:101::D、2000::5EFE:C0A5:101
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）A、The show ip ospf neighbors command lists two neighbors off Fa0/0.B、The show ip ospf neighbors command lists four neighbors off Fa0/0.C、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
单选题Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（）AFEA0::200:FF:FE11:0BFE80::200:FF:FE11:1111CFE80::0213:19FF:FE7B:0:1DFEB0::211:11FF:FE11: 1111
单选题Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。AThe Mac address of the NIC in Sever1BThe IP address of Server 1.CThe MAC address of the s0/0/0 interface of router R2DThe IP address of the s0/0/0 interface of router R1EThe IP address of the Fa0/0 interface of router R1
单选题Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100AThe output describes the contents of a Type 5 LSAB3.3.3.3 identifies a ro uter as being the router performing redistributionCR1's metric for its best route to reach the router with RID 9.9.9.9 is 100DThe router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
单选题Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1（）。AThe MAC address of the NIC in Host 1BThe MAC address of the NIC in server 1CThe MAC address of the Fa0/0 interface of router R1DThe MAC address of the s0/0/0 interface of the router R2
单选题R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1（）。AThe frame does not have MAC addresses.BThe source MAC address in the frame is the MAC address of the NIC of Host 1.CThe source MAC address in the frame is the MAC address of the s0/0/0 interface of R1.DThe destination MAC address in the frame is the MAC address of the NICof server 1.EThe destination MAC address in the frame is the MAC address of the s0/0/0 interface of R2
单选题Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。AThe IP address of sever 1.BThe MAC address of NIC in sever 1.CThe IP address of F0/0 interface of router R1.DThe MAC address of the Fa0/0 interface of router R1.EThe IP address of the s0/0/0 interface of router R2FThe MAC address of the s0/0/0 interface of router R2
多选题A network administrator wants to ensure that only the server can connect to port Fa0/1 on a Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is about to bring the server onlinE.What can the administrator do to ensure that only the MAC address of the server is allowed by switch port Fa0/1? （）AConfigure port Fa0/1 to accept connections only from the static IP address of the server.BEmploy a proprietary connector type on Fa0/1 that is incompatible with other host connectors.CConfigure the MAC address of the server as a static entry associated with port Fa0/1.DBind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.EConfigure port security on Fa0/1 to reject traffic with a source MAC address other than that of the server.FConfigure an access list on the switch to deny server traffic from entering any port other than Fa0/1.
多选题Which destination addresses will be used by Host A to send data to Host C?（）Athe IP address of Switch 1Bthe MAC address of Switch 1Cthe IP address of Host CDthe MAC address of Host CEthe IP address of the router's E0 interfaceFthe MAC address of the router's E0 interface
多选题Host 1 has just started up and requests a web page from web server 2. Which two statements describe steps in the process Host 1 uses to send the request to web server 2 (choose two)（）。AHost 1 addresses the frames to the MAC address of router R1BHost 1 looks in its ARP cache for the MAC address of router R1CHost 1 addresses the frames to the MAC address of web server 2DHost 1 sends the packets to router R1 to be forwarded to web server 2EHost 1 sends a broadcast ARP request to obtain the MAC address of webserver2
多选题Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）AThe show ip ospf neighbors command lists two neighbors off Fa0/0.BThe show ip ospf neighbors command lists four neighbors off Fa0/0.CThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.DThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
多选题Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command. Which of the following commands must have been configur ed on R1's Fa0/0 interface?（）Aip ospf authentication nullBip ospf authentication message - digestCip ospf authentication -key whatever- it - isDip ospf message - digest - key 1 md5 whatever - it - isEip ospf md5 1 key whatever - it - is